Hp T2200 Manual de usuario

HP R/T2200 UPS User Guide Part Number 404314-004 August 2008 (Fourth Edition)

Component identification 10 Item Description 3 Load segment 3 (one IEC-320-C13 output receptacle for surge and battery backup protection) 4 Load s

Component identification 11 • The REPO feature shuts down UPS units operating under either utility or battery power. Option 2: User supplied norma

Installation 12 Installation Precautions Save these instructions. This document contains important safety instructions that should be followed during

Installation 13 • Elevated operating ambient temperature—If the equipment is installed in a closed or multi-unit rack assembly, the operating ambien

Installation 14 1. Remove the UPS front bezel. 2. Attach the logo badge above the LED/Control panel.

Installation 15 3. From inside the bezel, gently push out the LED/Control panel, rotate it 90 degrees, and then replace it in the bezel. 4. Replace

Installation 16 WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling feet are extended to the f

Installation 17 3. Insert screws through the rack into the mounting rail and the front of each mounting bracket. Do not completely tighten the screws

Installation 18 Connecting the batteries WARNING: The unit contains sealed lead-acid battery modules. To prevent fire or chemical burns: • Do no

Installation 19 2. Connect the battery lead to the battery terminal. NOTE: A small amount of arcing may occur when connecting the batteries. Th

© Copyright 2006, 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warra

Installation 20 When using an ERM, set the Battery Charge Level switch (DIP switch 3) to the down position, increasing the UPS charger output and cha

Installation 21 CAUTION: Use only the computer interface cable supplied with the UPS to connect the communications port to the host computer.

Installation 22 CAUTION: Using a USB to serial converter cable will damage the UPS. Connecting the REPO port WARNING: To meet the requireme

Installation 23 Connecting the ground bonding cable The ground bonding screw is provided as an attachment point for conductors. Use a ground bond

Installation 24 Before connecting devices, verify that the UPS will not overload by checking that the ratings of the devices do not exceed the UPS ca

Installation 25 1. Attach the logo badge above the LED/Control panel. 2. Stand the unit on its side with the LED/Control panel at the top. Instal

Installation 26 NOTE: Mounting hardware for square- and round-holed racks is included in the UPS kit. 1. Attach the 2U side-mounting brackets t

Installation 27 3. Insert screws through the rack into the mounting rail and the front of each mounting bracket. Do not tighten. 4. Insert screws t

Installation 28 Connecting the ERM to the UPS This symbol indicates the presence of electric shock hazards. The area contains no user or field s

Installation 29 Charging the ERM batteries Connect the UPS to a grounded utility power outlet. When the UPS is plugged in, the unit automatically ent

Contents 3 Contents Component identification...

UPS operations 30 UPS operations Initiating a self-test A self-test can be performed with equipment connected to the UPS output receptacles. To init

UPS operations 31 different settings for this dial. As the dial is turned clockwise, the UPS becomes more tolerant of variations in the input power&

Power management 32 Power management Power management software HP Power Manager software ensures maximum power reliability of computer systems throu

Maintenance 33 Maintenance Updating the UPS firmware To update the UPS firmware, see the HP website (http://www.hp.com/go/rackandpower). CAUTION:

Maintenance 34 Battery care and storage guidelines CAUTION: Because of the short shelf life of the batteries, avoid storing a battery spare as a

Maintenance 35 3. Disconnect the battery leads. 4. Remove the battery bracket. 5. Remove the UPS battery modules. IMPORTANT: Do not pull the

Maintenance 36 To replace the component, reverse the removal procedure. IMPORTANT: Charge the batteries for at least 24 hours before supplying

Troubleshooting 37 Troubleshooting UPS does not start Action: 1. Be sure that the power cord is plugged in to a utility power receptacle. 2. Check

Troubleshooting 38 1. Save your work. 2. Power down the load devices connected to the UPS output receptacles. 3. Remove one or more load devices to

Troubleshooting 39 a. Consider saving your work and powering down the UPS (on page 31). If the blackout or brownout is prolonged, the Battery Charge

Contents 4 UPS does not communicate with the host computer ... 37

Specifications 40 Specifications UPS physical specifications Parameter Value Height 8.9 cm (3.5 in) Depth 48.3 cm (19 in) Width 44.5 cm (17.5

Specifications 41 Power protection specifications UPS model VA Nominal power rating (W) Nominal voltage setting R/T2200 NA/JPN/TWN 2200 1600 1

Specifications 42 Feature Specification Charging Complete charge takes no more than 24 hours. After approximately 4 hours, the batteries reach 90% c

Spares 43 Spares Ordering spares To order a spare, visit the HP website (http://h61003.www6.hp.com). To replace parts under warranty, contact an HP a

Technical support 44 Technical support Before you contact HP Be sure to have the following information available before you call HP: • Technical su

Warranty information 45 Warranty information Limited warranty To back up the wide range of features offered with the UPS, a 3-year limited warranty

Regulatory compliance notices 46 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance

Regulatory compliance notices 47 energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

Regulatory compliance notices 48 Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Cana

Regulatory compliance notices 49 This symbol on the product or on its packaging indicates that this product must not be disposed of with your other

Contents 5 Battery replacement notice...

Regulatory compliance notices 50 Class B equipment Battery replacement notice WARNING: Power products contain sealed lead-acid battery modules

Electrostatic discharge 51 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Acronyms and abbreviations 52 Acronyms and abbreviations EPO emergency power off ERM extended runtime module HPPM Hewlett-Packard Power Manager I

Index 53 A alarm conditions 30 alarms, silencing 30 authorized reseller 44 B backup time, insufficient 38 batteries, care and storage 34 ba

Index 54 insufficient backup time 38 International model 9 J Japanese notice 49 L LED, power button 7 LEDs 6, 7 LEDs, troubleshooting 37

Index 55 UPS, installing 12, 13 USB connectors 21 V Voltage Correction LED, location 7 Voltage Correction LED, troubleshooting 39 voltage spe

Component identification 6 Component identification UPS front panel Item Description 1 Battery compartment 2 Control buttons and LED display

Component identification 7 UPS front panel controls and LED indicators Item Description Function 1 Power On/Standby button Turns the UPS power

Component identification 8 Item Description Function 5 Battery Charge LED When the UPS is operating from utility power (the Power LED is green),

Component identification 9 Item Description 1 Load segment 1 (one NEMA 5-15 output receptacle for surge and battery backup protection) 2 Loa