HP NF758LA Point of Sale Guía de usuario

Busca en linea o descarga Guía de usuario para Terminales Punto De Venta HP NF758LA Point of Sale. HP NF758LA Point of Sale Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir

Indice de contenidos

Pagina 1 - Hardware Reference Guide

Hardware Reference GuideHP rp5700

Pagina 2

KeyboardTable 1-3 Keyboard Components1 Function Keys Perform special functions depending on the software application being used.2 Editing Keys Includ

Pagina 3 - About This Book

Using the Windows Logo KeyUse the Windows Logo key in combination with other keys to perform certain functions available in theWindows operating syste

Pagina 4

Special Mouse FunctionsMost software applications support the use of a mouse. The functions assigned to each mouse buttondepend on the software applic

Pagina 5 - Table of contents

2 Hardware UpgradesServiceability FeaturesThe computer includes features that make it easy to upgrade and service. No tools are needed for mostof the

Pagina 6

Using the Computer in a Tower OrientationThe computer can be configured in a tower orientation using the tower stand. The HP logo plate on thefront be

Pagina 7 - 1 Product Features

9. Lift the computer so that its right side is facing down (1) and place it on the stand (2). Be sure thatthe arrow on the stand is pointing toward th

Pagina 8 - Front Panel Components

Removing the Computer Cover1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact

Pagina 9 - Rear Panel Components

Replacing the Computer CoverPlace the computer cover on the chassis about 1.3 cm (½ inch) in front of the final position and slide itback into place u

Pagina 10 - Keyboard

Removing the Bezel BlankOn some models, a bezel blank covering the 5.25-inch external drive bay must be removed beforeinstalling a drive. To remove a

Pagina 11 - Using the Windows Logo Key

Installing Additional MemoryThe computer comes with double data rate 2 synchronous dynamic random access memory (DDR2-SDRAM) dual inline memory module

Pagina 12 - Serial Number Location

© Copyright 2007 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Microsoft and Windows are

Pagina 13 - 2 Hardware Upgrades

Populating DIMM SocketsThere are four DIMM sockets on the system board, with two sockets per channel. The sockets arelabeled DIMM 1, DIMM 2, DIMM 3, a

Pagina 14

should be populated with the two 512MB DIMMs. With this configuration, 2 GB will run as dualchannel and 256 MB will run as single channel.●In any mode

Pagina 15

8. Raise the drive cage to the upright position.Figure 2-7 Rotating the Drive Cage Up9. Rotate the fan duct out of the chassis.Figure 2-8 Rotating t

Pagina 16 - Removing the Computer Cover

10. Press the latch release on the front of the power supply (1), and then raise the power supply to theupright position (2).Figure 2-9 Releasing and

Pagina 17 - Replacing the Computer Cover

15. Return the fan duct to the down position.16. Return the drive cage to the down position.17. Replace the computer cover.18. If the computer was on

Pagina 18 - Removing the Bezel Blank

Removing or Installing an Expansion CardThe computer has the following expansion slots:●one ADD2/SDVO expansion slot●one low-profile PCI Express x1 ex

Pagina 19 - Installing Additional Memory

To install an ADD2/SDVO card or a PCI Express card:1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable

Pagina 20 - Populating DIMM Sockets

8. Remove the expansion slot cover or the existing expansion card.a. If you are installing an expansion card in a vacant socket, remove the appropriat

Pagina 21 - Installing DIMMs

CAUTION: After removing an expansion card, you must replace it with a new card or expansionslot cover for proper cooling of internal components during

Pagina 22

16. Lock any security devices that were disengaged when the computer cover was removed.17. Reconfigure the computer, if necessary. Refer to the Comput

Pagina 23

About This BookThis guide provides basic information for upgrading this computer model.WARNING! Text set off in this manner indicates that failure to

Pagina 24

9. Open the slot cover retainer that secures the slot covers by turning the retainer to the side.Figure 2-18 Opening the Riser Card Expansion Slot Re

Pagina 25 - 1 ADD2/SDVO expansion slot

b. If you are replacing an existing card, hold the PCI card at each end, and carefully rock it backand forth until the connectors pull free from the s

Pagina 26

13. To install a new expansion card in the riser card, align the bracket on the expansion card with theopen slot on the rear of the chassis and press

Pagina 27

20. Lock any security devices that were disengaged when the computer cover was removed.21. Reconfigure the computer, if necessary. Refer to the Comput

Pagina 28

Installing and Removing DrivesWhen installing additional drives, follow these guidelines:●The primary Serial ATA (SATA) hard drive must be connected t

Pagina 29

Removing and Replacing the Optical Drive (some models)CAUTION: All removable media should be taken out of a drive before removing the drive from theco

Pagina 30

8. Pull out the lever on the left side of the drive (1) to release the drive, and then slide the drive forwardout of the drive bay (2).Figure 2-25 Re

Pagina 31

3. Align the guide screws on the drive with the slots on the chassis. Slide the drive into the opticaldrive bay all the way back until it locks.Figure

Pagina 32

Removing and Replacing the Primary 3.5-inch Internal SATA Hard DriveNOTE: The system does not support Parallel ATA (PATA) hard drives.Before you remov

Pagina 33 - Drive Positions

8. If an optical drive is installed, disconnect the power cable (1) and data cable (2) from the back ofthe optical drive.Figure 2-30 Disconnecting th

Pagina 34

iv About This Book ENWW

Pagina 35

10. Pull out the lever on the left side of the primary hard drive (1) to release the drive, and then slidethe drive up out of the drive cage (2).Figur

Pagina 36

2. Insert the primary hard drive “upside down.” Align the hard drive with the primary hard drive bay inthe drive cage so that the bottom of the hard d

Pagina 37

4. Connect the power cable (1) and data cable (2) to the back of the optical drive, if applicable.Figure 2-36 Connecting the Optical Drive Power and

Pagina 38

7. Raise the drive cage to the upright position.Figure 2-37 Rotating the Drive Cage Up8. Press the latch release on the front of the power supply (1)

Pagina 39

9. Disconnect the power cable (1) and data cable (2) from the back of the secondary hard drive.Figure 2-39 Disconnecting the Secondary Hard Drive Pow

Pagina 40

To install a secondary hard drive:1. Install two 6–32 standard guide screws in the lower holes on each side of the drive.NOTE: When replacing the seco

Pagina 41

3. Connect the hard drive power and data cables to the back of the secondary hard drive.NOTE: The primary hard drive data cable must be connected to t

Pagina 42

A SpecificationsDesktop DimensionsHeightWidthDepth3.94 in13.40 in15.00 in10 cm34 cm38 cmApproximate Weight 19.6 lb 8.9 kgTemperature RangeOperatingNon

Pagina 43

B USB PlusPower Ports (some models)Some models have a USB PlusPower expansion card installed. This card provides one red-colored 24–volt USB+ connecto

Pagina 44

CAUTION: Regardless of the power-on state, voltage is always present on the system board aslong as the system is plugged into an active AC outlet. You

Pagina 45

Table of contents1 Product FeaturesStandard Configuration Features ...

Pagina 46

8. Install the new USB PlusPower Expansion Card in the lower socket of the riser card.a. Align the bracket on the card with the open slot on the rear

Pagina 47 - A Specifications

C Powered Serial PortsTwo powered serial ports, COM 1 and COM 2, are standard on the computer. Some models have apowered serial port expansion card in

Pagina 48

Removing the Powered Serial Port CapsThese powered serial ports have been protected with plastic caps. Turn off the computer and removethe caps before

Pagina 49

Configuring Power to a Serial PortThe serial ports on the HP Point of Sale System computer can be configured as standard (non-powered)serial ports or

Pagina 50

Item Port Name1 COM 42COM 3To configure power to the serial ports:1. Remove/disengage any security devices that prohibit opening the computer.2. Remov

Pagina 51 - C Powered Serial Ports

7. Press the latch release on the front of the power supply (1), and then raise the power supply to theupright position (2)Figure C-6 Releasing and R

Pagina 52

10. Install the new Powered Serial Port Expansion Card in the upper socket of the riser card.a. Align the bracket on the card with the open slot on th

Pagina 53 - 3P17 COM 2

Table C-1 Configuring Serial Port PowerENWW Configuring Power to a Serial Port 51

Pagina 54 - Item Port Name

52 Appendix C Powered Serial Ports ENWW

Pagina 55

D Battery ReplacementThe battery that comes with the computer provides power to the real-time clock. When replacing thebattery, use a battery equivale

Pagina 56

Installing a Security Lock ... 56Cabl

Pagina 57

8. Depending on the type of battery holder on the system board, complete the following instructionsto replace the battery.Type 1a. Lift the battery ou

Pagina 58

b. Insert the new battery and position the clip back into place.Figure D-3 Removing a Coin Cell Battery (Type 3)NOTE: After the battery has been repl

Pagina 59 - D Battery Replacement

E External Security DevicesNOTE: For information on data security features, refer to the Computer Setup (F10) Utility Guide andthe Desktop Management

Pagina 60

PadlockFigure E-2 Installing a PadlockENWW Installing a Security Lock 57

Pagina 61

F Electrostatic DischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

Pagina 62 - E External Security Devices

G Computer Operating Guidelines,Routine Care and Shipping PreparationComputer Operating Guidelines and Routine CareFollow these guidelines to properly

Pagina 63

Optical Drive PrecautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation●Do not move the drive dur

Pagina 64 - F Electrostatic Discharge

IndexAADD2/SDVO card 19audio connectors 3Bbackup and recovery 36battery replacement 53Ccomputer coverlocking and unlocking 56removing 10replacing 11co

Pagina 65

shipping preparation 60specificationscomputer 41memory 13Ttower orientation 8Uunlocking computer cover 56USB portsrear panel 3Vventilation guidelines

Pagina 66 - Shipping Preparation

1 Product FeaturesStandard Configuration FeaturesThe HP Point of Sale System rp5700 features may vary depending on the model. For a complete listingof

Pagina 67

Front Panel ComponentsDrive configuration may vary by model.Table 1-1 Front Panel Components1 5.25-inch Optical Drive (some models)15 Dual-State Powe

Pagina 68

Rear Panel ComponentsTable 1-2 Rear Panel Components1 Power Cord Connector 6 RJ-45 Network Connector2 PS/2 Mouse Connector (green) 7 Parallel Connect

Comentarios a estos manuales

Sin comentarios