HP ProLiant DL370 G6 Especificaciones

HP ProLiant DL/ML370 G6 Server Maintenance and Service Guide Abstract This guide is for an experienced service technician. HP assumes you are qualif

Customer self repair 10 enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que l

Cabling 100 Cabling Storage device cabling guidelines CAUTION: To prevent damage to the equipment, be sure that the server is powered down, all

Cabling 101 Item Description 3 SAS connector B 4 DVD-ROM drive 5 Hard drive cage 1, SAS connector 2 6 Hard drive cage 1, SAS connector 1 SAS hard

Cabling 102 Two-bay LFF drive cage cabling • Two-bay LFF drive cage cabling to an optional six-bay LFF backplane Item Description 1 Drive cag

Cabling 103 Six-bay LFF backplane cabling • Drive cage bay 1 • Drive cage bay 2

Cabling 104 Eight-bay SFF drive cage cabling • Drive cage bay 1 • Drive cage bay 2

Cabling 105 • Drive cage bay 3 SAS expander cabling The colors are shown for illustration purposes only. Item Description 1 SAS expander ca

Cabling 106 Item Description 2 SAS expander card, connectors E and F 3 SAS expander card, connectors G and H 4 SAS expander card, connectors A and

Cabling 107 DVD-ROM drive cabling Slimline optical drive cabling

Cabling 108 Power cabling Server power cabling (basic configuration) Item Description 1 Power supply backplane connector 2 24-pin power connec

Cabling 109 Server power cabling (maximum configuration) The colors are shown for illustration purposes only. Item Description 1 Video card, sl

Customer self repair 11 Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma van HP. Informatie over

Cabling 110 Hard drive cage power cabling Item Description 1 24-pin power connector 2 Power supply backplane connector 3 Hard drive bay 1 (must u

Cabling 111 Front panel cabling Item Description 1 Front USB connector 2 Front video connector 3 Systems Insight Display connector 4 Front panel

Cabling 112 BBWC battery pack and FBWC capacitor pack cabling

Specifications 113 Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) Shi

Specifications 114 Specification Value Input requirements Rated input voltage 100 to 120 VAC, 200 to 240 VAC Rated input frequency 50 Hz to 60 Hz

Specifications 115 Rated input power 526 W at 100V AC input 505 W at 200V AC input BTUs per hour 1794 at 100V AC input 1725 at 200V AC input Power s

Acronyms and abbreviations 116 Acronyms and abbreviations AMP Advanced Memory Protection BBWC battery-backed write cache CSR Customer Self Repair

Acronyms and abbreviations 117 RBSU ROM-Based Setup Utility RDIMM registered dual in-line memory module SAS serial attached SCSI SATA serial ATA

Documentation feedback 118 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documenta

Index 119 A access panel 31 additional information 80 air baffle 26, 34 B battery 89 battery cabling for BBWC 112 battery pack LEDs 96 b

Customer self repair 12 No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua essas peças, serão cobradas

Index 120 HP Insight Diagnostics survey functionality 80 HP Insight Remote Support software 81 HP NC375i adapter 63 HP NC524SFP Dual Port 10Gb

Index 121 server specifications 113 side panels, removing 38 six-bay LFF backplane 47, 103 slimline optical drive 43, 107 Smart Array P410i

Customer self repair 13

Customer self repair 14

Customer self repair 15

Illustrated parts catalog 16 Illustrated parts catalog Mechanical components Item Description Spare part number Customer self repair (on

Illustrated parts catalog 17 Item Description Spare part number Customer self repair (on page 6) 5 Miscellaneous hardware kit 519560-001 Mandat

Illustrated parts catalog 18 sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de servicio de garantía correspondiente al p

Illustrated parts catalog 19 System components Item Description Spare part number Customer self repair (on page 6) System components 9 Po

© Copyright 2009, 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warr

Illustrated parts catalog 20 Item Description Spare part number Customer self repair (on page 6) c) 2.00-GHz Intel Xeon processor E5504, 80W* **

Illustrated parts catalog 21 Item Description Spare part number Customer self repair (on page 6) X5677, 130W* ** cc) 3.33-GHz Intel Xeon process

Illustrated parts catalog 22 Item Description Spare part number Customer self repair (on page 6) e) Systems Insight Display sideband cable — — 2

Illustrated parts catalog 23 Item Description Spare part number Customer self repair (on page 6) 40 FBWC capacitor pack* 587324-001 Mandatory1 41

Illustrated parts catalog 24 3No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que el usuario haga v

Removal and replacement procedures 25 Removal and replacement procedures Required tools You need the following items for some procedures: • T-10/T-

Removal and replacement procedures 26 This symbol on an RJ-45 receptacle indicates a network interface connection. WARNING: To reduce the risk o

Removal and replacement procedures 27 • Extend the server from the rack (on page 28). If you are performing service procedures in an HP, Compaq bra

Removal and replacement procedures 28 4. Press the server rail-release latches and remove the server from the rack. 5. Place the server on a st

Removal and replacement procedures 29 2. After performing the installation or maintenance procedure, slide the server into the rack by pressing the

Contents 3 Contents Customer self repair ...

Removal and replacement procedures 30 2. Swing open the cable management arm. 3. Remove the cables from the cable trough. 4. Remove the cable mana

Removal and replacement procedures 31 2. Remove the tower bezel. To replace the component, reverse the removal procedure. Access panel WARNING:

Removal and replacement procedures 32 IMPORTANT: When replacing one failed fan only in a redundant configuration, powering down the server is not

Removal and replacement procedures 33 4. Remove the cache module. To replace the component, reverse the removal procedure. BBWC battery pack or FB

Removal and replacement procedures 34 5. Remove the battery pack. To replace the component, reverse the removal procedure. Air baffle To remove th

Removal and replacement procedures 35 6. Remove the air baffle. To replace the component, reverse the removal procedure. Fan cage IMPORTANT: W

Removal and replacement procedures 36 7. Remove the fan cage. To replace the component, reverse the removal procedure. Fan blank CAUTION: To p

Removal and replacement procedures 37 7. Remove the fan blank. To replace the component, reverse the removal procedure. Fans 1-4 CAUTION: To p

Removal and replacement procedures 38 5. Remove the fan. To replace the component, reverse the removal procedure. Tower side panels To remove the

Removal and replacement procedures 39 o Rear (1) o Front (2) 4. Remove the chassis from the tower side panels:

Contents 4 HP NC524SFP Dual Port 10GbE Module ... 65

Removal and replacement procedures 40 a. Disengage the chassis from the tower side panels by pushing the bottom side panel back and by pulling the c

Removal and replacement procedures 41 3. Remove the feet. To replace the component, slide it back into the locking slot. Be sure that the foot clic

Removal and replacement procedures 42 2. Back up all server data on the hard drive. 3. Remove the hard drive. To replace the component, reverse th

Removal and replacement procedures 43 To remove the component: 1. Power down the server (on page 27). 2. Do one of the following: o Open or remov

Removal and replacement procedures 44 6. Remove the air baffle ("Air baffle" on page 34). 7. Remove the fan cage ("Fan cage" on

Removal and replacement procedures 45 Remove the component as indicated. To replace the component, reverse the removal procedure. Hard drive cages

Removal and replacement procedures 46 8. Disconnect the data and power cables from the two-bay LFF drive cage. 9. Remove all LFF drives installed i

Removal and replacement procedures 47 12. Using a T-15 Torx screwdriver, remove the backplane from the drive cage. CAUTION: To prevent improper

Removal and replacement procedures 48 10. Using a T-15 Torx screwdriver, remove the six-bay LFF backplane. CAUTION: To prevent improper cooling

Removal and replacement procedures 49 9. Using a T-10 Torx screwdriver, remove the eight-bay SFF drive cage from drive cage bay 1. 10. Using a T-1

Contents 5 Server specifications ...

Removal and replacement procedures 50 o Extend the server from the rack (on page 28). 3. Remove the access panel ("Access panel" on page

Removal and replacement procedures 51 CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are popul

Removal and replacement procedures 52 11. Remove the eight-bay SFF drive cage from bay 3. 12. Using a T-15 Torx screwdriver, remove the backplane

Removal and replacement procedures 53 o If only one hot-plug power supply is installed, power down and remove the power cord from the server ("

Removal and replacement procedures 54 9. Remove the heatsink. To replace the heatsink: 1. Use the alcohol swab to remove all the existing thermal

Removal and replacement procedures 55 3. Install the heatsink. and close the heatsink retaining latches. 4. Install the air baffle. 5. If removed

Removal and replacement procedures 56 Locate and download the latest ROM version from the HP website (http://www.hp.com/support). Follow the instruc

Removal and replacement procedures 57 c. Release the tabs, and then carefully lift the processor and tool straight up. 12. Carefully rotate the to

Removal and replacement procedures 58 To replace a processor: 1. Carefully insert the processor into the processor installation tool. Handle the pr

Removal and replacement procedures 59 2. Be sure the tool is oriented correctly. Align the processor installation tool with the socket, and then ins

Customer self repair 6 Customer self repair HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow fo

Removal and replacement procedures 60 3. Press and hold the tabs on the processor installation tool to separate it from the processor, and then remo

Removal and replacement procedures 61 5. Install the heatsink, and then close the heatsink retaining latches. 6. Install the air baffle. 7. If re

Removal and replacement procedures 62 8. Remove the DIMM. To replace the component, reverse the removal procedure. For DIMM configuration informati

Removal and replacement procedures 63 5. Open the expansion board retainer. 6. Remove the expansion board. To replace the component, reverse the

Removal and replacement procedures 64 5. If installed, remove the BBWC battery pack or the FBWC capacitor pack ("BBWC battery pack or FBWC capa

Removal and replacement procedures 65 11. Remove the mini-DIMM, if installed. 12. Remove the HP NC524SFP Dual Port 10GbE Module ("HP NC524SFP

Removal and replacement procedures 66 Save the retaining screw. 9. Open the expansion board slot retainer. 10. Remove the HP NC375i adapter (&quo

Removal and replacement procedures 67 3. Remove the access panel ("Access panel" on page 31). 4. Remove fan 5 ("Fan 5" on page

Removal and replacement procedures 68 9. Remove the Systems Insight Display cables from the system board. To replace the component, reverse the remo

Removal and replacement procedures 69 o Open or remove the tower bezel, as needed ("Tower bezel" on page 30). o Extend the server from th

Customer self repair 7 Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièc

Removal and replacement procedures 70 7. Remove the battery. IMPORTANT: Replacing the system board battery resets the system ROM to its default

Removal and replacement procedures 71 3. Remove the access panel ("Access panel" on page 31). 4. Remove all expansion boards ("PCIe

Removal and replacement procedures 72 c. Release the tabs, and then carefully lift the processor and tool straight up. 15. Carefully rotate the to

Removal and replacement procedures 73 17. Using the system board tray handles, slide the tray forward and remove the failed system board. To replac

Removal and replacement procedures 74 2. Open the processor locking lever and the processor socket retaining bracket. Do not remove the processor so

Removal and replacement procedures 75 4. Align the processor installation tool with the socket, and then install the processor. THE PINS ON THE SYST

Removal and replacement procedures 76 5. Press the tabs on the processor installation tool to separate it from the processor, and then remove the to

Removal and replacement procedures 77 9. Apply all the grease to the top of the processor in the following pattern to ensure even distribution. 10.

Removal and replacement procedures 78 19. Power up the server. After you replace the system board, you must re-enter the server serial number and th

Removal and replacement procedures 79 The cables are not shown for clarity. To replace the component, reverse the removal procedure.

Customer self repair 8 In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il giorno lavorativo s

Diagnostic tools 80 Diagnostic tools Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving commo

Diagnostic tools 81 Survey functionality is installed with every SmartStart-assisted HP Insight Diagnostics installation, or it can be installed thr

Diagnostic tools 82 USB support HP provides both standard USB 2.0 support and legacy USB 2.0 support. Standard support is provided by the OS through

Component identification 83 Component identification Front panel components Item Description 1 USB connectors (2) 2 Drive cage blank 3 SAS/SATA

Component identification 84 Front panel LEDs and buttons Item Description Status 1 Power On/Standby button and system power LED Green = Normal

Component identification 85 Systems Insight Display LEDs The HP Systems Insight Display LEDs represent the system board layout. Item Description

Component identification 86 Systems Insight Display LED and color Health LED System power LED Status Processor (amber) Red Amber One or mor

Component identification 87 Rear panel components Item Description 1 Mouse connector 2 Keyboard connector 3 Serial connector 4 iLO 2 connecto

Component identification 88 Rear panel LEDs Item Description Status 1 UID LED Blue = Activated Flashing blue = System is being managed remotely

Component identification 89 System board components Item Description 1 SD card slot 2 Power backplane connector 3 Processor 1 DIMM slots 4 Power

Customer self repair 9 defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer Self Repair kommt

Component identification 90 Item Description 26 Slot 10 PCIe2 x8 (8, 4, 2, 1) 27 Internal USB connector 28 Processor socket 2 29 Processor 2 DIMM s

Component identification 91 The memory subsystem may be populated with either RDIMMs or UDIMMs, but mixing the two types is not supported. To determ

Component identification 92 Position Description Function S5 Password protection override Off = No function On = Clears power-on password and admi

Component identification 93 • SFF hard drives • LFF hard drives

Component identification 94 SAS and SATA hard drive LEDs Item Description Status 1 Fault/UID LED Amber = Drive failure Flashing amber = Fault

Component identification 95 Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation Flashing regularly (1 Hz) Off Do not remove the dr

Component identification 96 Battery pack LEDs Item Color Description 1 Green System Power LED. This LED is on when the system is powered up

Component identification 97 LED3 pattern LED4 pattern Interpretation Off Flashing (1 Hz) The battery pack is below the minimum charge level and i

Component identification 98 1 Green LED 2 Amber LED Interpretation Off Off The flash code is corrupt. Power supply backplane connectors Conn

Component identification 99 • Six-bay LFF backplane • Eight-bay SFF backplane Drive cage Installation Pin setting 1 Standard No jumper 2 Opt