HP ProLiant ML110 Guía de usuario

HP ProLiant ML110 G7 Server User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and storage sys

Component identification 10 System board components Item Description 1 HP dedicated iLO management connector 2 System maintenance switch 3 RPS ca

Specifications 100 Rated input frequency 50 Hz to 60 Hz Rated input current 5.5 A at 100 VAC 2.6 A at 200 VAC Rated input power 526 W at 100V AC inp

Technical support 101 Technical support Before you contact HP Be sure to have the following information available before you call HP: • Technical s

Technical support 102 • Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, howe

Technical support 103 Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzion

Technical support 104 CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standort

Technical support 105 Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedo

Technical support 106 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente

Technical support 107

Technical support 108

Acronyms and abbreviations 109 Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility AMP Advanced Memory Protection ASR A

Component identification 11 Item Description 27 Rear USB connectors (4) System maintenance switch Position Default Function 1 Off Off = iL

Acronyms and abbreviations 110 NMI non-maskable interrupt NVRAM non-volatile memory ORCA Option ROM Configuration for Arrays PCIe peripheral comp

Acronyms and abbreviations 111 SIM Systems Insight Manager TMRA recommended ambient operating temperature TPM trusted platform module UDIMM Unreg

Index 112 A access panel 20, 21 air baffle 21, 22 Array Configuration Utility (ACU) 65 ASR (Automatic Server Recovery) 67 authorized reselle

Index 113 firmware 71 front bezel 19, 20 front panel buttons 7 front panel components 7 front panel LEDs 7 G general diagnosis flowchart

Index 114 POST problems flowchart 84 power cord 74, 97 power distribution unit (PDU) 26 Power On button 19, 27 power requirements 26 power

Component identification 12 Item LED description Status 1 Power supply 1 failure Red = Power supply 1 failed Off = Normal 2 Power supply 2 (redun

Component identification 13 SAS and SATA device numbering LFF device bay numbering SFF device bay numbering

Component identification 14 SAS and SATA hard drive LEDs Item Description 1 Fault/UID LED (amber/blue) 2 Online LED (green) SAS and SATA h

Component identification 15 Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation Off Steadily amber A critical fault condition has

Component identification 16 BBWC module LEDs Item ID Color Description 1 Green System Power LED. This LED illuminates steadily when the syst

Component identification 17 LED3 pattern LED4 pattern Interpretation — One blink per second The battery pack is below the minimum charge level and

Component identification 18 Green LED Amber LED Interpretation Flashing (2 Hz) Alternating with amber LED Flashing (2 Hz) Alternating with green L

Operations 19 Operations Power up the server To power up the server, press the Power On/Standby button. Power down the server WARNING: To reduc

© Copyright 2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties

Operations 20 3. Pull out the bezel. Installing the front bezel 1. Insert the bezel. 2. Close and lock the bezel. 3. Power on the server (&quo

Operations 21 CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed.

Operations 22 4. Remove the air baffle. Installing the air baffle CAUTION: For proper cooling do not operate the server without the access pan

Operations 23 Removing the full-length expansion board retainer 1. Power down the server (on page 19). 2. Remove the access panel ("Removing

Operations 24 5. Install the full-length expansion board retainer, and then close the PCIe slot cover retainer latch. 6. Install the access panel

Setup 25 Setup Optional installation services Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and

Setup 26 Temperature requirements To ensure continued, safe, and reliable equipment operation, install or position the system in a well-ventilated,

Setup 27 Identifying the contents of the server shipping carton Unpack the server shipping carton and locate the materials and documentation necessa

Setup 28 Registering the server To register the server, refer to the HP Registration website (http://register.hp.com).

Hardware options installation 29 Hardware options installation Introduction If more than one option is being installed, read the installation instru

Contents 3 Contents Component identification ...

Hardware options installation 30 The server memory control subsystem selects the proper rank within the DIMM when writing to or reading from the DIM

Hardware options installation 31 CAUTION: To avoid damage to the hard drives, memory, and other system components, the air baffle, drive blanks, a

Hardware options installation 32 General DIMM slot population guidelines • The HP ProLiant ML110 G7 Server has four memory slots. • The HP ProLian

Hardware options installation 33 CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated

Hardware options installation 34 3. Remove the hard drive. Installing a hard drive The server supports up to four non-hot-plug SATA hard drives, f

Hardware options installation 35 3. Prepare the hard drive. 4. Install the hard drive. Hot-plug LFF hard drive cage option 1. Power down the se

Hardware options installation 36 6. Using a T-15 Torx screwdriver, remove the four screws, and then remove the hard drive cage from the drive cage b

Hardware options installation 37 o Connect the cable to an HP Smart Array SAS RAID controller. Item Description 1 Connect the power cable 2 Con

Hardware options installation 38 11. Install the access panel. ("Installing the access panel" on page 21) 12. Install the front bezel

Hardware options installation 39 6. Using a T-15 Torx screwdriver, remove the four screws, and then remove the hard drive cage from the drive cage b

Contents 4 Single- and dual-rank DIMMs ... 29

Hardware options installation 40 9. Slide the drive cage assembly fully into the server chassis and install the four screws. 10. Install the hard

Hardware options installation 41 3. Remove the access panel ("Removing the access panel" on page 20). 4. Remove the optical drive blank.

Hardware options installation 42 6. Connect the optical drive and power cables to the optical drive. 7. Install the access panel ("Installing

Hardware options installation 43 5. Remove the nonredundant power supply. 6. Disconnect and remove all devices from the two media drive bays. o R

Hardware options installation 44 o Remove the EMI shield, if installed. 7. Install the redundant power supply cage. 8. Insert the redundant powe

Hardware options installation 45 9. Install one or two redundant power supplies into the redundant power supply cage. When fully inserted, the r

Hardware options installation 46 10. Remove the four screws, and then loosen the drive cage. 11. Route and connect the redundant power supply cabl

Hardware options installation 47 Installing the BBWC battery/FBWC capacitor pack and cache module CAUTION: To prevent a server malfunction or da

Hardware options installation 48 9. Install the cache module on the controller. 10. Connect the battery/capacitor pack cable to the connector on t

Hardware options installation 49 11. Connect the battery/capacitor pack cable to the pack. 12. Install the battery/capacitor pack. 13. Install t

Contents 5 HP Insight Diagnostics ...

Hardware options installation 50 Removing an expansion slot cover CAUTION: For proper cooling do not operate the server without the access panel

Hardware options installation 51 6. Install the expansion board. 7. Connect any required internal or external cables to the expansion board. See t

Hardware options installation 52 3. Enabling the Trusted Platform Module (on page 54). Enabling the TPM requires accessing the ROM-Based Setup Utili

Hardware options installation 53 6. Install the TPM board. Press down on the connector to seat the board. 7. Install the TPM security rivet by pre

Hardware options installation 54 • Always store copies of the recovery key/password away from the server. • Do not save the recovery key/password

Cabling 55 Cabling Storage cabling Non-hot-plug four LFF SATA hard drive cabling Item Description 1 Optical drive bay (1 to 2) 2 Non-hot-plug

Cabling 56 Hot-plug four LFF SAS hard drive cabling Item Description 1 Optical drive bay 2 Hot-plug LFF hard drive bay (1 to 4) 3 LFF backpla

Cabling 57 Item Description 1 Optical drive bay 2 Hot-plug SFF hard drive bay (1 to 8) 3 SFF backplane 4 Optical drive bay cable 5 I2C cable 6

Cabling 58 Eight SFF Smart Array SAS RAID controller card cabling Item Description 1 Optical drive bay 2 Hot-plug SFF hard drive bay (1 to 8) 3 S

Cabling 59 Power cabling Four LFF hard drive non-hot-plug, nonredundant power cabling Item Description 1 Optical drive bay power cable 2 Optio

Contents 6 Acoustics statement for Germany (Geräuschemission) ... 97

Cabling 60 Four LFF hard drive hot-plug, redundant power cabling Item Description 1 Optical drive bay power cable 2 LFF backplane power cable

Cabling 61 Eight SFF hard drive hot-plug, redundant power cabling Item Description 1 Optical drive bay power cable 2 SFF backplane power cable

Cabling 62 Optical drive cabling Item Description 1 Optical drive bay 2 Optional optical drive bay 3 Optical drive bay cable 4 Optional optica

Configuration and utilities 63 Configuration and utilities Configuration tools SmartStart software SmartStart is a collection of software that optim

Configuration and utilities 64 • Displaying system information • Selecting the primary boot controller • Configuring memory options • Language s

Configuration and utilities 65 For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD or the HP website

Configuration and utilities 66 Option ROM Configuration for Arrays Before installing an operating system, you can use the ORCA utility to create the

Configuration and utilities 67 Management tools Automatic Server Recovery ASR is a feature that causes the system to restart when a catastrophic ope

Configuration and utilities 68 • Send alerts from iLO 3 regardless of the state of the host server. • Access advanced troubleshooting features thr

Configuration and utilities 69 HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and other related

Component identification 7 Component identification Front panel components Item Description 1 Optical drive bay 2 USB connectors (4) Front pane

Configuration and utilities 70 service level. Notifications may be sent to your authorized HP Channel Partner for on-site service, if configured and

Configuration and utilities 71 • VCRM manages the repository for Windows and Linux PSPs as well as online firmware. Administrators can browse a gra

Configuration and utilities 72 • Deploys software and firmware on Windows and Linux operating systems • Performs local or remote (one-to-many) onl

Troubleshooting 73 Troubleshooting Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common

Troubleshooting 74 Symbols on equipment The following symbols may be placed on equipment to indicate the presence of potentially hazardous condition

Troubleshooting 75 WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The

Troubleshooting 76 2. Record any error messages displayed by the system. 3. Remove all diskettes, CD-ROMs, DVD-ROMs, and USB drive keys. 4. Power

Troubleshooting 77 When requested to break the server down to the minimum configuration, uninstall the following components, if installed: • All ad

Troubleshooting 78 Service notifications To view the latest service notifications, refer to the HP website (http://www.hp.com/go/bizsupport). Select

Troubleshooting 79 General diagnosis flowchart The General diagnosis flowchart provides a generic approach to troubleshooting. If you are unsure o

Component identification 8 Item Description Status 1 System health LED Green = Normal Amber = System degraded Red = System critical 2 NIC 1 li

Troubleshooting 80 Item See 5 "General memory problems are occurring" in the HP ProLiant Servers Troubleshooting Guide located on the Doc

Troubleshooting 81 Server power-on problems flowchart Symptoms: • The server does not power on. • The system power LED is off or amber.

Troubleshooting 82 • The external health LED is red or amber. • The internal health LED is red or amber. NOTE: For the location of server LED

Troubleshooting 83

Troubleshooting 84 POST problems flowchart Symptoms: • Server does not complete POST NOTE: The server has completed POST when the system att

Troubleshooting 85 Item See 13 • "Server information you need" in the HP ProLiant Servers Troubleshooting Guide located on the Documenta

Troubleshooting 86 OS boot problems flowchart Symptoms: • Server does not boot a previously installed operating system • Server does not boot Smar

Troubleshooting 87 Server fault indications flowchart Symptoms: • Server boots, but a fault event is reported by Insight Management Agents • Ser

Troubleshooting 88 Possible causes: • Improperly seated or faulty internal or external component • Unsupported component installed • Redundancy f

Troubleshooting 89 POST error messages and beep codes For a complete listing of error messages, refer to the "POST error messages" in th

Component identification 9 4 Slot 1 PCIe2x16 (16, 8, 4, 1) 5 Slot 2 PCIe2x8 (4, 1) 6 Slot 3 PCIe2x8 (4, 1) 7 Slot 4 PCIe2x4 (1) 8 USB connectors (4)

Troubleshooting 90 WARNING: To avoid potential problems, ALWAYS read the warnings and cautionary information in the server documentation before re

Battery replacement 91 Battery replacement If the server no longer automatically displays the correct date and time, you might have to replace the b

Regulatory compliance notices 92 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance

Regulatory compliance notices 93 Declaration of conformity for products marked with the FCC logo, United States only This device complies with Part

Regulatory compliance notices 94 European Union regulatory notice Products bearing the CE marking comply with the following EU Directives: • Low Vo

Regulatory compliance notices 95 Japanese notice BSMI notice Korean notice Class A equipment Class B equipment

Regulatory compliance notices 96 Chinese notice Class A equipment Laser compliance This product may be provided with an optical storage device (th

Regulatory compliance notices 97 Taiwan battery recycling notice The Taiwan EPA requires dry battery manufacturing or importing firms in accordance

Electrostatic discharge 98 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Specifications 99 Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) Ship