HP Server tc2110 Manual de instalación descargar pdf

Setting Up the HP Server

HP Server

Installation Sheet

Notice

) ) ) )

tc2110

The information contained in this document is subject to change

without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the

furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability

of its software on equipment that is not furnished by

Hewlett-Packard.

This document contains proprietary information that is protected by

photocopied, reproduced, or translated to another language without

the prior written consent of Hewlett-Packard Company.

Intel and Pentium are registered trademarks of Intel Corporation.

Microsoft , Windows NT , and Windows 2000 are registered

trademarks of Microsoft in the U.S. and other countries.

Torx is a registered trademark of CamCar/Textron, Incorporated.

Hewlett-Packard Company

Network Server Division

Technical Communications

10955 Tantau Avenue

Cupertino, California 95014 USA

P5498-90005

Printed in February 2002 Printed on recycled paper

Audience Assumptions

This guide is for the person who installs, administers, and troubleshoots

LAN servers. Hewlett-Packard Company assumes you are qualified in the

servicing of computer equipment and trained in recognizing hazards in

products with hazardous energy levels. The instructions in this document

are provided in greater detail in the HP Server tc2110 Operation and

Maintenance Guide.

Configuring the HP Server

1. Check/set the Power Supply Input Voltage Switch:

 ❑ The input voltage switch is located above the power connector.

  The default setting is 230 volts.

2. Connect all peripherals:

 ❑ Connect the keyboard, mouse, monitor, and UPS to the

  HP Server.

3. Run Diagtools (Optional):

 ❑ Insert the HP Startup CD-ROM in the CD-ROM drive.

 ❑ Press F2 to continue, and then verify the hardware configuration.

 ❑ Verify the HP Server's BIOS version against the latest BIOS

  version listed on HP's web site for this server at:

  http:\\www.hp.com.

 ❑ If you do not have the latest BIOS, update the BIOS now. Refer

  to the HP Server tc2110 Operations and Maintenance Guide

  for instructions.

 ❑ Save the support ticket to a diskette for future reference.

4. Install the desired Network Operating System (NOS).

 ❑ Refer to the HP Server tc2110 NOS Installation Guide

  for instructions on installing the NOS.

NOTE: If you are using an optional tape backup device, install and

  configure the tape backup software now. Refer to the Tape

  Backup Getting Started Guide for instructions.

5. Refer to the HP Server Documentation CD-ROM:

 ❑Use this CD-ROM for updated information about your HP Server,

  and as a reference for any additional information not provided in

  this Installation Sheet.

1 2 3 4

Indice de contenidos

Pagina 1 - HP Server

Setting Up the HP Server HP Server Installation SheetNotice) ) ) )tc2110The information contained in this document is subject to change without notice

Pagina 2 - Familiarize Yourself

Familiarize Yourself (continued)Opening the HP ServerFamiliarize YourselfCAUTIONsThe keyboard and mouse PS/2 ports are not interchangeable. If a devic

Pagina 3 - (continued)

Installing Mass Storage DevicesReplacing the ProcessorCAUTION Drives can be damaged by static electricity. Before   handling drives, touch an unpai

Pagina 4 - Installing Memory

Replacing the Processor (continued)Boot PriorityCAUTION Align pin 1 on the processor with pin 1 on the   processor socket, or pin damage will occur