Hp ProLiant BL465c Gen8 Server Blade Manual de usuario Pagina 39
- Pagina / 89
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Hardware options installation 39
• When one processor is installed, install DIMMs in sequential alphabetic order: A, B, C, D, E, F, and so
forth.
• When two processors are installed, install the DIMMs in sequential alphabetic order balanced between
the two processors: P1-A, P2-A, P1-B, P2-B, P1-C, P2-C, and so forth.
• For DIMM spare replacement, install the DIMMs per slot number as instructed by the system software.
For detailed memory configuration rules and guidelines, use the Online DDR3 Memory Configuration Tool
on the HP website (http://www.hp.com/go/ddr3memory-configurator).
DIMM speeds are supported as indicated in the following table.
Populated slots
(per channel)
Rank Speeds supported
(MT/s)
1, 2
Single or dual 1600, 1333, 1066
1, 2
Quad* 1333
*LRDIMMs are the only supported quad-rank DIMMs for this server blade.
Advanced ECC population guidelines
For Advanced ECC mode configurations, observe the following guidelines:
• Observe the general DIMM slot population guidelines (on page 38).
• DIMMs may be installed individually.
Online spare population
For Online Spare memory mode configurations, observe the following guidelines:
• Observe the general DIMM slot population guidelines (on page 38).
• Each channel must have a valid online spare configuration.
• Each channel can have a different valid online spare configuration.
• Each populated channel must have a spare rank:
o A single dual-rank DIMM is not a valid configuration.
o LRDIMMs are treated as dual-rank DIMMs.
Population order
For memory configurations with a single processor or multiple processors, populate the DIMM slots in the
following order:
• LRDIMM: Sequentially in alphabetical order (A through H)
• RDIMM: Sequentially in alphabetical order (A through H)
After installing the DIMMs, use RBSU to configure Advanced ECC or online spare memory support.
Installing DIMMs
To install the component:
1. Power down the server blade (on page 12).
2. Remove the server blade (on page 13).
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- Drive LED definitions 8
- System board components 8
- System maintenance switch 9
- DIMM slot locations 10
- Tool location 11
- HP c-Class Blade SUV Cable 11
- Operations 12
- Remove the server blade 13
- Remove the access panel 14
- Install the access panel 14
- Remove the DIMM baffle 14
- Install the DIMM baffle 15
- Operations 17 17
- Remove the SAS controller 18
- Install the SAS controller 19
- Remove all drives 20
- Remove drive 2 21
- Overview 22
- Connecting to the network 24
- Installing a server blade 25
- Completing the configuration 26
- Introduction 27
- Drive option 27
- Prepare the drive 28
- 6. Install the drive 29
- Processor option 30
- Memory options 34
- HP SmartMemory 35
- DIMM identification 37
- Memory configurations 37
- Installing DIMMs 39
- Mezzanine card option 40
- Capacitor pack option 42
- Cabling 48
- Drive cabling 49
- USB devices 49
- USB mouse 51
- Item Description 51
- Server mode 52
- Server QuickSpecs 52
- HP iLO Management Engine 52
- Active Health System 53
- Intelligent Provisioning 54
- HP Insight Diagnostics 55
- Erase Utility 55
- Scripting Toolkit 56
- HP Service Pack for ProLiant 57
- HP ROM-Based Setup Utility 57
- Using RBSU 58
- Auto-configuration process 58
- Boot options 59
- Configuring AMP modes 59
- Utilities and features 60
- ROMPaq utility 61
- Automatic Server Recovery 61
- USB support 61
- Keeping the system current 62
- Software and firmware 63
- Version control 63
- ProLiant Servers 63
- Troubleshooting 64
- Battery replacement 65
- FCC rating label 66
- Modifications 67
- • EMC Directive 2004/108/EC 68
- Japanese notice 69
- BSMI notice 69
- Korean notice 69
- Chinese notice 70
- Ukraine notice 70
- Laser compliance 70
- Battery replacement notice 71
- Electrostatic discharge 73
- Specifications 74
- Support and other resources 75
- Customer Self Repair 77
- Reparo feito pelo cliente 79
- Acronyms and abbreviations 83
- Documentation feedback 85
- Index 86 86
- Index 87 87
- Index 88 88
- Index 89 89
Relacionado con productos y manuales para Hardware De La Computadora Hp ProLiant BL465c Gen8 Server Blade
(9 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.126 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales