HP AWSXCIG-1A Manual de usuario

HP Workgroup System and XC SoftwareInstallation GuideVersion 1.0HP Part Number: A-WSXCIG-1APublished: August 2008Edition: 1

CommandA command name or qualified command phrase.Computer outputText displayed by the computer.Ctrl+x A key sequence. A sequence such as Ctrl+x indic

1 HP Workgroup System OverviewThe HP Workgroup System is delivered to you factory assembled and ready for deployment.HP Workgroup System solutions off

IMPORTANT: Be sure there is a blade in Bay 1. See Figure 1-2 for enclosure bay numbering.Figure 1-2 Enclosure Bay NumberingFigure 1-3 shows an example

2 Hardware PrerequisitesGather the following information before starting the installation process. HP recommend thatyou download all device drivers, f

• For information on displaying the installed version of firmware, see the service guide forthe hardware component.• For the supported firmware versio

3 Hardware SetupFor more information about the HP Workgroup System specifications and thermal stabilization,see Appendix B (page 47).3.1 Unpack the En

5. Remove the front section of the bottom cushion (Callout 2) and the ramp. (callout 1,Figure 3-3)Figure 3-3 Removing the Ramp and Front Cushion6. Att

Figure 3-5 Rolling the Unit Down the RampFigure 3-6 Rolling the Unit to the Installation Location8. Plug the unit into a power source.3.2 Installing a

Figure 3-7 Interconnect SwitchThe following list describes the callouts in Figure C-1:1. Port 20 RJ-45 connector for 10/100/1000 Mb uplink2. Port 21 R

d. For Bay 1, specify the IP addresses 172.31.15.1. Click Autofill to populate the remainingIP addresses.e. Wait 60 seconds for the assignments to tak

© Copyright 2008 Hewlett-Packard Development Company, L.P.Confidential computer software. Valid license from HP required for possession, use or copyin

NOTE: The OA automatically creates user accounts for itself (prefixed with the letters OA)to provide single sign-on capabilities. Do not remove these

6. Use the virtual power functions to turn off power to the server blade.7. Close the iLO2 utility web page.8. Repeat this procedure from every active

22

4 Software PrerequisitesHave the following information ready before starting the installation process. Because it isassumed that you will not have an

NOTE: An internal DVD drive is included in the HP Workgroup System enclosure.4.2 Downloading XC Software PatchesFor each supported version of the HP X

If you have not received the license key file, contact your HP representative.4.4 Associating the Enclosure DVD to the Head NodeTo associate the enclo

26

5 XC Software InstallationFor more details on the following steps, see the HP XC System Software Installation Guide, Section2.3.2.NOTE: The XC Softwar

5.2 Running the cluster_prep CommandIMPORTANT: Some HP XC patches might need to be run before cluster_prep. Check theReadme file of all patches for mo

NOTE: Enter the letter R to change a response.Restarting network ... done5.3 Installing Patches from Your LaptopTo install the XC Software patches fro

Table of ContentsAbout This Document...9Intended

6. To install the patches, change into each directory using cd. Follow the instructions in theReadme file.For more information on how to install the p

3. Enter the following command:# cd /opt/hptc/config/sbin4. Enter the following command:# ./discover --enclosurebased --single --ic=AdminNet5. Enter t

Example 5-2 cluster_config Command Output 1Given that there are # nodes in this cluster, enter the number ofNFS daemons that shall be configured to su

Example 5-3 cluster_config Command Output 2[O]k, [R]especify Interfaces: OInterfaces over which traps will be accepted: loopback Admin[O]k, [R]espec

The Golden Image will be created next. [P]roceed, [Q]uit: PCAUTION: Do not interrupt or stop the golden image creation. Do not browse or touchfiles. D

2. Enter the following command:# manage_enclosure listtrap[root@n1 sbin] manage_enclosure listtrapn-enc09CN8734016G: 172.31.15.240[root@n1 sbin]#5.9

# lsidPlatform LSF HPC 6.2 for SLURM, LSF_build_dateCopyright 1992-2005 Platform Computing CorporationMy cluster name is hptclsfMy master name is lsfh

• The run number, which represents the number of times the OVP has been run. The runnumber is not included for the first run.For example, the log file

Slurm Monitor 1-Ok 0-Warn 0-Crit 0-Pend 0-UnkSlurm Status 10-Ok 0-Warn 0-Crit 0-Pend 0-Unk

# export SYS_CHECK_SYSWIDE=1# sys_check > /tmp/filename.htmlBy default, the sys_check utility creates the report in HTML format, but there is an op

6 Troubleshooting...416.1 Unable to Manually

>> VLAN 2 add 7>> VLAN 2 add 8>> VLAN 2 add 21>> VLAN 2 add 23>> VLAN 2 ena6. Assuming that the switch ssh or telnet man

6 Troubleshooting6.1 Unable to Manually Set IP Addresses for the iLOs1. Verify that the iLOs are set to DHCP enabled.2. Power down the node.3. Then po

Example 6-2 Modify Database4. (Optional) Edit the file /etc/sysconfig/netinfo to reflect the correct external networkinformation and MAC address.Examp

6.5 Lost Terminal Window When in the IRCIf a terminal window fails to open in the IRC, press CTL ALT Backspace. This will take youback to the login sc

44

A Additional Software Setup InformationTo change the iLO default user name and password1. Under the hardware model, click iLO.2. In the body of the ma

46

B Additional Hardware Setup InformationB.1 HP Workgroup System SpecificationsTable B-1 HP Workgroup System SpecificationsHeight 54.1 cm (21.20 in)Widt

Table B-2 Thermal Stabilization Specification (continued)Minimum Stabilization TimeAmbient Shipping Temperature Range(°F)Ambient Shipping Temperature

C IP Addresses on a Corporate NetworkUse this method if you have access to the corporate network and a DHCP server providing IPaddresses. In order to

List of Figures1-1 Example Front View...

Figure C-3 OA IP AddressOn the warning page, click Continue to this website.5. Enter the Administrator user name and the password supplied with the HP

D Configure sendmailLSF requires a mail program to send job output to users who submit jobs and to sendadministrative messages to the LSF administrato

Consult any third-party Linux system administration reference manual if you need moreinformation about configuring sendmail.To use a mail program othe

GlossaryAadministrationnetworkThe private network within the HP XC system that is used for administrative operations.Bbase image The collection of fil

iLO2 The next generation of iLO that provides full remote graphics console access and remote virtualmedia.See also iLO.image server A node specificall

MySQL A relational database system developed by MySQL AB that is used in HP XC systems to storeand track system configuration information.NNAT Network

Sserver blade One of the modules of an HP BladeSystem. The server blade is the compute module consistingof the CPU, memory, I/O modules and other supp

IndexAadministrative networkconfiguring VLAN for, 39testing, 36BbackupCMDB, 38bad golden image, 42boot order, 19Ccluster_config, 31cluster_prep, 28CMD

XXC installation, 27XC license, 24XC patches, 2458 Index

59

List of Tables2-1 HP BladeSystem c-Class Firmware and Management Tools Upgrades...14B-1 HP Workgroup System Specif

List of Examples5-1 Sample XC.lic File...

8

About This DocumentThis document describes how to set up the hardware and install the XC software on your HPWorkgroup System.IMPORTANT: This document