HP EliteDesk 705 G1 Small Form Factor PC (ENERGY STAR) Manual de usuario

Hardware Reference GuideHP EliteDesk 705 G1 Small Form Factor

Media card reader componentsThe media card reader is an optional device available on some models only. Refer to the followingillustration and table to

Serial number locationEach computer has a unique serial number and a product ID number that are located on the exteriorof the computer. Keep these num

2 Hardware upgradesServiceability featuresThe computer includes features that make it easy to upgrade and service. No tools are needed formost of the

Removing the computer access panelTo access internal components, you must remove the access panel:1. Remove/disengage any security devices that prohib

Replacing the computer access panelSlide the lip on the front end of the access panel under the lip on the front of the chassis (1) thenpress the back

Removing the front bezel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact dis

Removing bezel blanksOn some models, there are bezel blanks covering the 3.5-inch and slim optical drive bays that needto be removed before installing

Replacing the front bezelInsert the four hooks on the bottom edge of the bezel into the rectangular holes on the chassis (1)then rotate the top side o

Changing from desktop to tower configurationThe Small Form Factor computer can be used in a tower orientation with an optional tower stand thatcan be

System board connectionsRefer to the following illustration and table to identify the system board connectors for your model.No. System Board Connecto

© Copyright 2014 Hewlett-PackardDevelopment Company, L.P.Microsoft and Windows are U.S. registeredtrademarks of the Microsoft group ofcompanies.The in

Installing additional memoryThe computer comes with double data rate 3 synchronous dynamic random access memory (DDR3-SDRAM) dual inline memory module

●The system will operate in flex mode if the total memory capacity of the DIMMs in Channel A isnot equal to the total memory capacity of the DIMMs in

7. Open both latches of the memory module socket (1), and insert the memory module into thesocket (2).NOTE: A memory module can be installed in only o

Removing or installing an expansion cardThe computer has two PCI Express x1 expansion slots, one PCI Express x16 expansion slot, andone PCI Express x1

a. If you are installing an expansion card in a vacant socket, remove the appropriateexpansion slot cover on the back of the chassis. Pull the slot co

c. If you are removing a PCI Express x16 card, pull the retention arm on the back of theexpansion socket away from the card and carefully rock the car

12. To install a new expansion card, hold the card just above the expansion socket on the systemboard then move the card toward the rear of the chassi

Drive positions1 Slim optical drive bay2 3.5-inch internal hard drive bay3 3.5-inch drive bay for optional drives (media card reader shown)4 2.5-inch

Installing and removing drivesWhen installing drives, follow these guidelines:●The primary Serial ATA (SATA) hard drive must be connected to the dark

CAUTION: To prevent loss of work and damage to the computer or drive:If you are inserting or removing a drive, shut down the operating system properly

About This BookThis guide provides basic information for upgrading the HP EliteDesk Business PC.WARNING! Text set off in this manner indicates that fa

Removing a 3.5-inch deviceCAUTION: All removable media should be taken out of a drive before removing the drive from thecomputer.1. Remove/disengage a

8. Disconnect the drive cables from the rear of the drive, or, if you are removing a media cardreader, disconnect the USB cable from the system board

Installing a 3.5-inch device1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact

9. Rotate the drive cage to its upright position.10. Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, u

11. If installing a USB 3.0 media card reader, you must use the USB 3.0 to USB 2.0 adapter (1) andconnect the adapter cable from the media card reader

Removing a slim optical driveCAUTION: All removable media should be taken out of a drive before removing the drive from thecomputer.1. Remove/disengag

Installing a slim optical drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as comp

9. Slide the optical drive through the front bezel all the way into the bay so that it locks in place (1),then connect the power cable (2) and data ca

Removing and replacing a 3.5-inch hard driveNOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive sothat you

8. Pull the release lever next to the rear of the hard drive outward (1). While pulling the releaselever out, slide the drive back until it stops, the

iv About This Book

10. Align the guide screws with the slots on the chassis drive cage, press the hard drive down intothe bay, then slide it forward until it stops and l

Removing a 2.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compa

8. Disconnect the power cable (1) and data cable (2) from the back of the hard drive.9. Pull outward on the release lever at the rear of the drive (1)

Installing a 2.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as com

9. Align the guide screws on the drive with the J-slots on the sides of the drive bay. Press the driveup into the drive bay then slide it forward unti

11. Rotate the drive cage back down to its normal position.CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down.12.

Installing a security lockThe security locks displayed below and on the following pages can be used to secure the computer.Cable lockPadlock40 Chapter

HP Business PC Security Lock1. Fasten the security cable by looping it around a stationary object.2. Insert the cable lock into the cable lock slot on

3. Slide the security cable through the hole in the cable lock on the rear of the monitor.4. Use the bracket provided in the kit to secure other perip

5. Thread the keyboard and mouse cables through the computer chassis lock.6. Screw the lock to the chassis in the thumbscrew hole using the screw prov

Table of contents1 Product features ...

7. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage thelock. Use the key provided to disengage the loc

Front bezel securityThe front bezel can be locked in place by installing a security screw provided by HP. To install thesecurity screw:1. Remove/disen

8. Install the security screw through the middle front bezel release tab to secure the front bezel inplace.9. Replace the access panel.10. If the comp

A Battery replacementThe battery installed on the computer provides power to the real-time clock. When replacing thebattery, use a battery equivalent

b. Slide the replacement battery into position, positive side up. The battery holderautomatically secures the battery in the proper position.Type 2a.

b. Insert the new battery and position the clip back into place.NOTE: After the battery has been replaced, use the following steps to complete this pr

B Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

C Computer operating guidelines, routinecare and shipping preparationComputer operating guidelines and routine careFollow these guidelines to properly

Optical drive precautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation●Do not move the drive dur

IndexAaccess panelremoval 7replacement 8Bbattery replacement 47Ccomputer operating guidelines 51DDIMMs. See memorydrivescable connections 22installati

Front bezel security ... 45Appendix A Batter

1 Product featuresStandard configuration featuresFeatures may vary depending on the model. For support assistance and to learn more about thehardware

Front panel componentsDrive configuration may vary by model. Some models have a bezel blank covering one or more drivebays.1 Slim Optical Drive (optio

Rear panel components1 PS/2 Mouse Connector (green) 7 PS/2 Keyboard Connector (purple)2RJ-45 Network Connector 8 DisplayPort Monitor Connectors3Serial