HP LC2000r - NetServer - 128 MB RAM Guía de instalación Pagina 113
- Pagina / 194
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 10 Configuring the HP NetServer
105
• Configure Remote Management:
This utility configures the Integrated Remote Management device for
remote management. It enables remote, dial-up HP NetServer
management.
To configure Integrated Remote Assistant, select Configure Remote
Management on the Configure Remote Management screen.
• Show System Information:
Use this screen to display information about standard and accessory boards
and devices in the system, as well as the used and available system
resources.
◊ Select View Hardware Inventory on the Show System Information
screen to display information about standard and accessory boards and
devices in the system.
◊ Select View Resources on the Show System Information screen to
display used and available system resources such as memory ranges,
I/O port ranges, DMA channels, and interrupt (IRQ) levels.
• Configure Disk Array:
This configures your HP disk array, but requires you to fill out the Disk
Array Configuration Worksheet before proceeding. Click Help for more
details.
• Install Utility Partition:
This step creates an 32 MB utility partition on the NetServer hard disk
where HP Navigator will copy DiagTools, the BIOS Update utility, the
Event Log Report utility, the Disk Array utility, the NIC Configuration
utility, the Integrated Remote Assistant utilities, troubleshooting utilities,
and other utilities. However, this is not available for SCO UNIX.
Select Execute on the Install Utility Partition screen.
• Execute Card Utilities:
Use this function, when Configuration Assistant detects installed boards,
which have additional configuration utilities on the HP NetServer
Navigator CD-ROM. By selecting Execute on the Execute Board Utilities
screen, you can execute these utilities to complete the configuration of the
boards.
- HP NetServer LC 2000/2000r 1
- Installation Guide 1
- Contents 3
- 1 Setting Up the HP NetServer 9
- Pedestal Installation 10
- Rack Mount Installation 13
- Front of HP NetServer 17
- Front Panel LED Indicators 19
- Power Supply Module Indicator 23
- Keyboard Mouse 24
- Video NIC 24
- (Embedded) 24
- Management 24
- NIC Indicators 25
- Link/Activity 25
- Transfer Rate 25
- Powering Up the HP NetServer 26
- Sleep States (ACPI) 27
- 3 Opening and Closing the HP 29
- NetServer 29
- Foot (4) 31
- Anti-Tip 31
- Foot Extended 31
- Slide Securing Screws (2) 33
- Hinge Pins(3) Handles(2) 33
- Top Cover 35
- Bottom Cover 35
- Cover Pull 35
- Right Cover 38
- Thumbscrews (2) 38
- Removing the Pedestal 40
- Hardware Mirroring 43
- Mass Storage Guidelines 44
- • General Guidelines 44
- • SCSI Device Selection 44
- • SCSI Drive Addressing 45
- • Filler Panels and Spacers 46
- Filler Panels 47
- Pedestal Configurations for 48
- Note: Con = Connector 49
- Connectors A and B 50
- Con = Connector 50
- Cabling Configurations 51
- Drive Spacer 55
- Locking Latch 56
- Removing Hot Swap Hard Drives 58
- Non-Hot Swap 59
- (Optional) 59
- DIMM Installation 64
- DIMM Removal 67
- Boot Priority 70
- IRQ Settings 71
- System Board PCI Slots 71
- Installing Accessory Boards 73
- 1. Open Tab 75
- 2. Lift Latch 75
- 3. Remove Slot Cover 75
- 1. Insert Board 77
- 2. Close Latch 77
- 3. Turn Tab 77
- Figure 7-1. System Board 80
- Installing the Processor 81
- Processor Cage 83
- Terminator 84
- Figure 7-6. Installing VRM 86
- Channel(2) 97
- Rear of HP NetServer 101
- Left Rear 101
- Rack Column 101
- Cable Management Arm 101
- Attaching the Front Bezel 102
- Mouse, and UPS 105
- Introduction 107
- HP NetServer Navigator CD-ROM 107
- Internet FTP 109
- Assistant 111
- • Show System Information: 113
- • Configure Disk Array: 113
- • Install Utility Partition: 113
- • Execute Card Utilities: 113
- NOS Installation 115
- HP Management Solutions 116
- Setup Utility 120
- Using the Setup Screens 121
- • Small arrow points ( 122
- ➢Hardware Security 123
- Floppy check: [Disabled] 126
- Summary screen: [Enabled] 126
- Quick Boot mode: [Enabled] 126
- ➢Boot Device Priority 126
- ➢Hard Drive Priority 126
- Clearing CMOS 128
- SCSI Configuration Utility 129
- 11 Information Assistant 135
- Installing from the CD-ROM 137
- :\infoasst\setup 137
- 12 Troubleshooting 139
- Common Installation Problems 140
- Chapter 12 Troubleshooting 141
- Error Message Is Displayed 142
- No Error Messages Displayed 143
- Open = Off 145
- Closed = On 145
- Hardware Problems 147
- Keyboard or Mouse Do Not Work 148
- CD-ROM Drive Does Not Work 148
- Password Problems 149
- Battery Problems 150
- 13 Alternative Rack Mounting 153
- Tools Required 154
- • Nut driver or wrench 154
- • T-15 and T-25 Torx Drivers 154
- • Marking pen 154
- Preparing the Rack 156
- Slide Members 161
- Screws (4) 161
- Mounting 162
- Channels(2) 162
- A Specifications 169
- Appendix A Specifications 170
- Environmental Requirements 171
- Physical Requirements 172
- Video Support 173
- B Regulatory Information 175
- Notice for Japan 177
- Notice for Korea 178
- Notice for Taiwan 179
- Notice for European Union 179
- Battery Statements 183
- C Service and Support 185
- Warranty 187
Relacionado con productos y manuales para Barebones Pc / Estación De Trabajo HP LC2000r - NetServer - 128 MB RAM
Barebones Pc / Estación De Trabajo HP 8000 - Elite Convertible Minitower PC Especificaciones rápidas
(76 paginas)
(76 paginas)
Barebones Pc / Estación De Trabajo HP Media Center,Pavilion Media Center m8330 Manual de usuario
(17 paginas)
(17 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales