HP LH6000r - NetServer - 0 MB RAM Guía de instalación Pagina 110
- Pagina / 186
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 10 Configuring the HP NetServer
102
NOTE The message "Configuration of NVRAM and drives mismatch"
indicates that configuration information in the integrated HP
NetRAID controller’s NVRAM differs from configuration
information in hard disk drives.
Do the following to clear configuration information from
integrated HP NetRAID NVRAM:
1. Press Ctrl+M to start the HP NetRAID Express Tools
utility.
2. On the Tools Management Menu, choose Configure.
3. On the Configure menu, choose Clear Configuration.
• If the question "Clear Configuration?" is displayed, answer
Yes. Then press any key to continue, and go to Step 4 in
this note.
• If the message "No Existing Configuration to Clear" is
displayed, press Esc to return to the Configuration menu,
choose New Configuration, and answer Yes to the
question "Proceed?". When the scan finishes, all drives are
shown in the Ready state. Press Enter to end the array, and
answer Yes to the question "Save Configuration?". When
"Configuration is Saved" is displayed, press any key.
4. To exit HP NetRAID Express Tools, press ESC repeatedly
until the Exit? box appears. Choose YES to exit. Then press
Ctrl+Alt+Del to restart the NetServer.
2. As soon as you see the message
Press <F2> to enter SETUP
on the display monitor, press the F2 function key.
NOTE If you wait too long to press the F2 function key, you may not
be able to enter the Setup utility, even though the message
"Press <F2> to enter SETUP" is still displayed. If this happens,
restart the HP NetServer and press the F2 function key as soon
as the message appears.
- HP NetServer 1
- LH 6000/6000r 1
- Installation Guide 1
- Audience Assumptions 2
- Contents 3
- 1 Setting Up the HP NetServer 9
- Rack Mount Installation 10
- Pedestal Installation 12
- Configuring the HP NetServer 14
- ◊ Restart the HP NetServer 15
- ◊ Install NOS: 17
- Front View 19
- Front Panel Console 20
- Door reveals this panel 21
- Viewing System Information 23
- Main Menu 24
- System Info Menu 26
- Component Info Menu 27
- Adjust Contrast Menu 27
- Activity 28
- Flexible Disk Drives 29
- Internal Hard Disk Drives 29
- Rear View 30
- Green (Power) LED 32
- Amber (Attention) LED 32
- Onboard LEDs 32
- Power Supplies 33
- Power-Up Procedure 34
- Power-Down Procedure 35
- Sleep States (ACPI) 35
- 3 Opening and Closing the HP 37
- NetServer 37
- Thumbscrew 41
- (1) Unlock the bezel 43
- Left Cover 44
- Mass Storage Guidelines 48
- Boot Priority 51
- Non-hot-swap 57
- Non-Hot-Swap SCSI Addressing 58
- Connecting SCSI Sub-systems 59
- Memory Guidelines 61
- Guidelines 68
- Tested PCI Boards and Drivers 69
- Installing Accessory Boards 70
- Front Board 72
- Hold Down 72
- PCI Hot Plug Boards 75
- Removing a Hot Plug Board 76
- 4. Remove the hot-plug board 77
- Configuration Guidelines 79
- Installing the Processor 80
- Figure 7-3. Open the Latches 82
- Figure 7-4. Insert the VRM 83
- Setting the Processor Speed 84
- Upgrading the Firmware 85
- Testing the Processor 86
- Re-installing the NOS 86
- Removing a Processor Module 86
- Tools Required 88
- Anti-tip 89
- System E/U Characteristics 90
- Installing Bezel Rack Nuts 92
- Installing the NetServer 97
- Top Cover 101
- Right Cover 101
- Bottom Cover 101
- Introduction 109
- HP NetServer Navigator CD-ROM 112
- Resource Mode 113
- Server Mode 115
- README File 116
- • Update System BIOS: 117
- • Select NOS: 117
- NOS installation? 117
- • Show System Information: 118
- • Configure Disk Array: 119
- • Install Utility Partition: 119
- • Execute Card Utilities: 119
- Essential Steps 120
- Recommended Steps 120
- NOS Installation 121
- HP Management Solutions 122
- TopTools Remote Control 123
- PcANYWHERE32 124
- NetServer Utilities 124
- Setup Utility 125
- Using the Setup Screens 127
- Power-On Password 129
- Hardware Security 129
- 1. [Bootable Cards] 133
- 12345678 134
- Verify Disk Drive Modules 138
- 11 Information Assistant 139
- General Information 140
- NetServer E-Series 140
- NetServer L-Series 140
- NetServer Accessories 140
- Server Management 141
- Getting Help 141
- Finding Information 141
- Installing from the CD-ROM 143
- :\INFOASST\setup 144
- 12 Troubleshooting 145
- Chapter 12 Troubleshooting 146
- Common Installation Problems 147
- DiagTools 149
- Error Messages 151
- Password Problems 153
- 13 Alternative Rack Mounting 155
- Preparing for Installation 157
- Installing the Slides 158
- Installing Rack Nuts 159
- Installing Bar Nuts 160
- Attaching the Slides 161
- A Specifications 165
- Environment 166
- Power Requirements 167
- B Regulatory Information 169
- Notice for United States 170
- Notice for Japan 171
- Notice for Korea 172
- Notice for Taiwan 173
- Battery Statements 177
- Power Line Harmonic Statement 178
- Noise and Ergonomic Statement 178
- C Service and Support 179
- Warranty 181
Relacionado con productos y manuales para Barebones Pc / Estación De Trabajo HP LH6000r - NetServer - 0 MB RAM
(8 paginas)
Barebones Pc / Estación De Trabajo HP ProLiant xw2x220c - Blade Workstation Manual de usuario
(22 paginas)
(22 paginas)
(158 paginas)
Barebones Pc / Estación De Trabajo HP Evo D510 - Convertible Minitower Manual de usuario
(66 paginas)
(66 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales