HP NetServer LXr 8000 Especificaciones

Artisan Technology Group is your source for quality new and certied-used/pre-owned equipment• FAST SHIPPING AND DELIVERY• TENS OF THOUSANDS OF IN-S

Chapter 1 Introduction5Table 1-1. Alternative Installation OperationsReceived Kit: Initial installation ofHP NetServer with the Compaqrack-optimized

Chapter 1 Introduction6Be sure that the stabilizing, anti-tip feature is installed on the rack enclosure inwhich you are installing the HP NetServer.

Chapter 1 Introduction7CAUTION If this HP NetServer is not installed according to theseinstructions, damage to the HP NetServer or accessories mayresu

Chapter 1 Introduction8ToolsThe following tools are required to install the HP NetServer in a Compaq rack:l T15 Torx® driverl Small thin flat-bladed s

92 Preparing the HP NetServerOverview of HP NetServer PreparationFollow the instructions in this chapter after you receive the Compaqrack-optimized ki

Chapter 2 Preparing the HP NetServer10Disconnect the HP NetServerWARNING Before removing the covers, always disconnect the powercord and unplug teleph

Chapter 2 Preparing the HP NetServer11Extend the HP NetServerIf the HP NetServer is already installed in a Compaq rack (without a front bezel),do the

Chapter 2 Preparing the HP NetServer122. To extend the HP NetServer from the rack, pull on the handle indicated inFigure 2-2.HandleFigure 2-2. Pull t

Chapter 2 Preparing the HP NetServer13Remove Bezel LatchIf a bezel latch is mounted on the right side of the HP NetServer, remove it toavoid interfere

Chapter 2 Preparing the HP NetServer14Remove the Control Panel BezelNOTE Do not remove the original HP rack-optimized control panelbezel until you hav

HP NetServer LXr 8000 andLXr 8500 Installation GuideforCompaq® 4000/7000 RacksHP Part Number 5967-6670Printed in September 1999Artisan Technology Grou

Chapter 2 Preparing the HP NetServer15Remove the Top Cover, Fan Cover, Fans, and FanCageRemove the entire top cover, fan cover, all fans, and the fan

Chapter 2 Preparing the HP NetServer164. Pull the fan cover forward, and then lift the front of it about 1 inch (3 cm).5. Push the fan cover backwards

Chapter 2 Preparing the HP NetServer177. Remove the three screws from the front of the fan cage, as shown inFigure 2-8.Figure 2-8. Removing the Fan C

Chapter 2 Preparing the HP NetServer18Disconnect the LCD CablesA ribbon cable and a twisted-pair cable connect the LCD to the front panel board,as sho

Chapter 2 Preparing the HP NetServer19Remove the Existing LCD CoverWARNING The LCD cover contains sheet metal with sharp edges. Handleit carefully to

Chapter 2 Preparing the HP NetServer203. Grasp the LCD assembly with both hands. Pull up firmly on the LCDassembly to lift it as high as possible. You

Chapter 2 Preparing the HP NetServer21Install the New LCD CoverWARNING The LCD cover contains sheet metal with sharp edges. Handleit carefully to avoi

Chapter 2 Preparing the HP NetServer222. Thread the LCD power cord and ribbon cable through the rectangular holein the rear half of the new LCD cover,

Chapter 2 Preparing the HP NetServer23Post (4 Places)Hole in Processor Trayfor LCD CablesLCD AssemblyFigure 2-14. Attaching the LCD Assembly(HP NetSe

Chapter 2 Preparing the HP NetServer24Reconnect the LCD CablesCAUTION When connecting the LCD cables, push the connector straightinto the socket. This

iiNoticeThe information contained in this document is subject to change without notice.Hewlett-Packard makes no warranty of any kind with regard to th

Chapter 2 Preparing the HP NetServer25Reinstall the Fan Cage, Fans, Fan Cover, and TopCoverCAUTION The light pipes on the underside of the fan cage ar

Chapter 2 Preparing the HP NetServer263. Install all six fans. Orient them with their arrow labels pointing to the rearof the HP NetServer. The fans a

Chapter 2 Preparing the HP NetServer275. Lower the top cover onto the top of the HP NetServer, about one half-inch(1 cm) to the rear of its normal pos

Chapter 2 Preparing the HP NetServer28Attach the New Control Panel BezelAttach the new control panel bezel, as shown in Figure 2-19. Push in the snap

293 Preparing the RackOverview of Rack PreparationWARNING To prevent the rack from tipping over, be sure that thestabilizing, anti-tip feature is inst

Chapter 3 Preparing the Rack30To mark the slide mounting holes, refer to Figure 3-1 and do the following:1. On the front columns, count up from the bo

Chapter 3 Preparing the Rack31Install the Cage NutsOnce you have marked the twelve holes, install a supplied cage nut in eachmarked hole on all column

Chapter 3 Preparing the Rack321. Loosen the two screws on the rear flange of the slide, but leave them inplace.2. Extend the rear flange by pushing it

334 Installing into the RackOverview of Installation into RackIf the HP NetServer is not yet mounted in the Compaq rack, do the following tomount it:l

Chapter 4 Installing into the Rack34Before you lift the HP NetServer, remove the power supply modules from the rearof the HP NetServer to reduce the w

iiiContentsAbout This Guide ... 11 Introduction...

Chapter 4 Installing into the Rack35Mount the HP NetServer on the Slides1. Verify that both slides are fully extended from the rack, as shown inFigure

Chapter 4 Installing into the Rack36Figure 4-3. Attaching the Slides to HP NetServer Chassis3. Line up the mounting holes in the slide members with t

Chapter 4 Installing into the Rack375. On both slide members, simultaneously depress the lockout releases shownin Figure 4-5. Then push the HP NetServ

Chapter 4 Installing into the Rack38Reinstall Power Supply ModulesReinstall all power supply modules. To install a power supply module:1. Pull down th

Chapter 4 Installing into the Rack39Compaq Rack-Optimized Front BezelTabsHP LogoNameplateSlotsHoles for StudsFigure 4-7. Attaching Nameplate to Compa

Chapter 4 Installing into the Rack40Install the Compaq Rack Front BezelInstall the front bezel optimized for Compaq racks as follows:1. Hold the bezel

41A Warranty and SupportRefer to the HP NetServer Warranty and Service/Support Booklet provided withyour original HP NetServer system documentation fo

Appendix A Warranty and Support42product by Customer from HP or Reseller. If HP or Reseller receives notice ofsuch defects during the warranty period,

43IndexAAccessories, 7Adjusting rack slides, 31American Power ConversionCorporation (APC), 7Anti-tip feature, 6BBezelcontrol panel, 14, 28front, 9, 38

Index44LCD cover, 3, 9, 19, 20, 21, 22, 23retainers, 22slots, 20, 23spring fingers, 19standoffs, 22Lifting handles, 36Lifting HP NetServer, 35Light pi

ContentsivInstall the Nameplate... 38Install the Compaq Rack Front

Artisan Technology Group is your source for quality new and certied-used/pre-owned equipment• FAST SHIPPING AND DELIVERY• TENS OF THOUSANDS OF IN-S

1About This GuideThis guide tells how to mount an HP NetServer LXr 8000 or 8500 into a Compaq®model 4000-series or 7000-series rack enclosure. Refer t

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

31 IntroductionCompaq Rack-Optimized KitThe front bezel, control panel bezel, and LCD cover shipped with yourHP NetServer LXr 8000 or 8500 were design

Chapter 1 Introduction4NOTE Until you receive the Compaq rack-optimized front bezel,control panel bezel, and LCD cover:• Leave the HP-optimized contro