HP t5740e Guía de usuario

Hardware Reference GuideHP t5740/t5745 Thin Clients

Rear Panel ComponentsFigure 1-4 Rear panel components(1) Wireless antenna* (6) PS/2 connectors (2)(2) Ethernet RJ-45 connector (7) Serial connector(3

Installing the Antenna (Wireless Models)▲Screw the antenna in place on the rear of the thin client.Figure 1-5 Installing the antennaCAUTION: To preve

To install the stand:1. Turn unit upside down.2. Locate the slots on the bottom of the unit into which the tabs on the stand fit.3. Insert the tabs in

Using the Power Cord Retention SlotTo prevent accidental disconnection, press a loop of the power cord into the power cord retentionslot.Figure 1-9 P

(6) Alt key Use in combination with another key; its function depends on theapplication software you are using.(7)Application key1Similar to the right

Windows Logo KeyUse the Windows Logo Key in combination with other keys to perform certain functions available inWindows operating systems.Windows Log

Serial Number LocationEvery thin client includes a unique serial number located as shown in the following illustration. Havethis number available when

2 Hardware ChangesGeneral Hardware Installation SequenceTo ensure the proper installation thin client hardware components:1. Back up any data, if nece

9. Install the stand, if you will be using the thin client unmounted in a vertical orientation. SeeInstalling the Stand on page 5 for more information

3. Remove the cover from the unit by first lifting the rear (screw side) of the cover, and then liftingthe cover off the unit (3).Figure 2-1 Removing

© Copyright 2009–2010 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Microsoft and Window

Removing and Replacing the Side Access Panel andMetal Side CoverRemoving the Side Access Panel and Metal Side CoverWARNING! Before removing the side a

2. Lift the metal side cover, front side first, off the unit (2).Figure 2-4 Removing the metal side coverReplacing the Metal Side Cover and Side Acce

2. Slide the panel toward the bottom of the unit until it locks into place (2).Figure 2-6 Replacing the side access panelInstalling Thin Client Optio

Installing the USB DeviceBefore beginning the replacement process, review General Hardware Installation Sequenceon page 11 for procedures you should f

2. To release the battery from its holder, squeeze the metal clamp that extends above one edge ofthe battery. When the battery pops up, lift it out (1

CAUTION: Static electricity can damage the electronic components of the computer or optionalcards. Before beginning these procedures, ensure that you

To install the SO-DIMM:1. Slide the serial number tab out of the way.NOTE: Be sure not to lose this tab.2. Remove the access plate:Figure 2-10 Removi

6. Replace the access plate:Figure 2-12 Replacing the SO-DIMM access platea. Insert the tab on the front edge into its slot and set the plate into po

A SpecificationsTable A-1 HPt5740/t5745 Thin ClientDimensionsWidth (front to back)Height (top to bottom, without stand)Depth (side to side)222 mm255

B Security ProvisionsSecuring the Thin ClientThe HPt5740/t5745 thin client is designed to accept a security cable lock. This cable lock preventsunauth

About This BookWARNING! Text set off in this manner indicates that failure to follow directions could result in bodilyharm or loss of life.CAUTION: Te

C Mounting the Thin ClientHP Quick ReleaseThe HPt5740/t5745 thin client incorporates four mounting points on each side of the unit. Thesemounting poin

To use the HP Quick Release with a VESA-configured thin client:1. Using four 15 mm screws included in the mounting device kit, attach one side of the

3. Slide the side of the mounting device attached to the thin client (1) over the other side of themounting device (2) on the device on which you want

Figure C-6 Thin client mounted on back of monitor stand●You can mount the thin client on a wall.Figure C-7 Thin client mounted on wall●You can mount

Non-supported Mounting OptionCAUTION: Mounting a thin client in an non-supported manner could result in failure of the HP QuickRelease and damage to t

D Thin Client OperationRoutine Thin Client CareUse the following information to properly care for your thin client:●Never operate the thin client with

Figure D-2 Horizontal orientation●You can lay the thin client under a monitor stand with at least one inch of clearance.Figure D-3 Under monitor sta

Non-supported OrientationHP does not support the following orientation for the thin client.CAUTION: Non-supported placement of thin clients could resu

E Electrostatic DischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

F Shipping InformationShipping PreparationFollow these suggestions when preparing to ship the thin client:1. Turn off the thin client and external dev

iv About This Book ENWW

IndexAaccess panelremoving 14replacing 15altitude specifications 22antennainstalling 5location 3Bbattery, replacing 17, 19Ccable lock slot location 3c

Rrated output current 22rear panel components 4relative humidity specifications22removingbattery 17, 19metal side cover 14secure USB compartmentcover

Table of contents1 Product Features ...

Appendix C Mounting the Thin Client ... 24HP

1 Product FeaturesStandard FeaturesThank you for purchasing an HP thin client. We hope you have years of use from our t5740 or t5745thin clients. Our

Thin Client Management SolutionsHP has a comprehensive suite of management solutions to fit your needs. This allows you to choosesolutions that will w

Top ComponentsFigure 1-2 Top components, external view(1) Cable lock slot(2) Secure USB compartmentFigure 1-3 Top components, internal view(1) Cable