HP D2200sb Manual de usuario

HP StorageWorks D2200sb PCIe Storage Blade User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers

Operations 10 IMPORTANT: If installing a hot-plug device, it is not necessary to power down the storage blade. To power down the storage blade,

Operations 11 o Partnered with a half-height server blade o Partnered with a full-height server blade 5. Place the storage blade on a flat, leve

Operations 12 To remove the component: 1. Power down the partner server blade (on page 9). 2. Remove the storage blade (on page 10). 3. Press t

Setup 13 Setup Kit contents When unpacking the HP StorageWorks D2200sb PCIe storage blade, locate the following items: • HP StorageWorks D2200sb P

Setup 14 Installation guidelines When installing the storage blade, observe the following guidelines: • Install hard drives in the storage blade be

Setup 15 Installing a storage blade CAUTION: To prevent improper cooling and thermal damage, do not operate the storage blade or the enclosure u

Setup 16 o To install the storage blade with a full-height server blade, install the half-height blade shelf. If installing two storage blades with

Setup 17 o Partnered with a half-height server blade o Partnered with a full-height server blade o Partnered with a full-height server blade and

Setup 18 6. Install a server blade. See the documentation that ships with the server blade. 7. Configure the storage blade ("Configurati

Setup 19 are not fully protected by system air flow. • A fast beep and flash (2 per second)—To avoid drive damage or data loss and storage blade sh

© Copyright 2010, 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warr

Setup 20 3. Prepare the hard drive. 4. Install the hard drive. 5. Install the storage blade in the enclosure. 6. Power up the partner server bl

Setup 21 WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before to

Setup 22 7. Install the FBWC module. To avoid possible damage to the storage blade, be sure that the module is fully seated before installing the sc

Configuration and utilities 23 Configuration and utilities Configuration tools Array Configuration Utility ACU is a browser-based utility with the f

Configuration and utilities 24 • Setting the controller to be the boot controller • Selecting the boot volume If you do not use the utility, ORCA

Configuration and utilities 25 Remote support and analysis tools HP Insight Remote Support software HP strongly recommends that you install HP Insig

Configuration and utilities 26 • The most recent version of a particular server blade or option firmware from the HP website (http://www.hp.com/sup

Troubleshooting 27 Troubleshooting If the storage blade does not power up If the storage blade does not start: 1. Be sure that the storage blade is

Troubleshooting 28 Answer Possible reasons Possible solutions LED ("Front panel LEDs" on page 6) indicates normal temperature. The har

Troubleshooting 29 For example, fault tolerance might occur when a drive in an array fails while another drive in the array is being rebuilt. Compro

Contents 3 Contents Component identification ...

Troubleshooting 30 o In RAID 1+0 configurations, any drives that are not mirrored to other removed or failed drives can be simultaneously replaced o

Troubleshooting 31 If this situation occurs, reboot the server. The system may temporarily become operational long enough to allow recovery of unsav

Troubleshooting 32 Some status messages are available without pressing the F3 key. For example, on the Main menu, the FAILED status appears next to

Regulatory compliance notices 33 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance

Regulatory compliance notices 34 Disposal of waste equipment by users in private households in the European Union This symbol on the product or o

Electrostatic discharge 35 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Specifications 36 Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) M

Support and other resources 37 Support and other resources Before you contact HP Be sure to have the following information available before you call

Support and other resources 38 providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship

Support and other resources 39 Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'in

Contents 4 Is the storage blade operating properly? ... 27 Re

Support and other resources 40 HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen,

Support and other resources 41 sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes

Support and other resources 42 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pel

Support and other resources 43

Support and other resources 44

Acronyms and abbreviations 45 Acronyms and abbreviations ACU Array Configuration Utility ADU Array Diagnostics Utility CPQONLIN NetWare Online Arr

Acronyms and abbreviations 46 UID unit identification

Documentation feedback 47 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentat

Index 48 A access panel 11 acoustics statement for Germany 36 ACU (Array Configuration Utility) 24 additional guidelines for installation with

Index 49 L LED, health 6 LED, internal health 6 LEDs, hard drive 7, 8 M Management Agents 25 management tools 25 O operations 9 ORCA (Op

Component identification 5 Component identification Front panel components Item Description 1 Product information tag 2 LED panel 3 Drive drawe

Component identification 6 Front panel LEDs Item Description Status 1 UID LED Blue = Identified Off = Not identified 2 System health LED* Gr

Component identification 7 SAS and SATA hard drive bay numbers SAS and SATA hard drive LEDs Item Description 1 Fault/UID LED (amber/blue) 2

Component identification 8 Online/activity LED (green) Fault/UID LED (amber/blue) Interpretation On Off The drive is online, but it is not active cu

Operations 9 Operations Important Safety Information Before installing this product, read the Important Safety Information document provided. Po