HP EliteDesk 880 G2 Base Model Tower PC Manual de usuario

Hardware Reference GuideHP EliteDesk 800 G2 TWR Business PC

Serial number locationEach computer has a unique serial number and a product ID number that are located on the exterior of thecomputer. Keep these num

2 Hardware upgradesServiceability featuresThe computer includes features that make it easy to upgrade and service. No tools are needed for most ofthe

Removing the computer access panelTo access internal components, you must remove the access panel:1. Remove/disengage any security devices that prohib

Replacing the computer access panelSlide the tabs on the front end of the access panel under the lip on the front of the chassis (1), and then pressth

Removing the front bezel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact dis

Removing bezel blanksOn some models, there may be bezel blanks covering the optical drive bays. You must remove the bezelblank before installing an op

System board connectionsRefer to the following illustration and table to identify the system board connectors for your model.No. System Board Connecto

No. System Board Connector System Board Label Color Component17 SATA 3.0 SATA3 light blue Any SATA Device other than thePrimary Hard Drive18 SATA 3.0

●The system will operate in single channel mode if the DIMM sockets are populated in one channel only.●The system will operate in a higher-performing

6. Open both latches of the memory module socket (1), and insert the memory module into the socket (2).NOTE: A memory module can be installed in only

© Copyright 2015 HP Development Company,L.P.Microsoft and Windows are U.S. registeredtrademarks of the Microsoft group ofcompanies.The information con

Removing or installing an expansion cardThe computer has two PCI Express x1 expansion sockets, one PCI Express x16 expansion socket, and one PCIExpres

a. If you are installing an expansion card in a vacant socket, remove the appropriate expansion slotcover on the back of the chassis. Pull the slot co

c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansionsocket away from the card and carefully rock the car

12. Rotate the slot cover retention latch back in place to secure the expansion card.13. Connect external cables to the installed card, if needed. Con

Drive positions1 5.25-inch half-height drive bay2 9.5mm slim optical drive bay3 Primary 3.5-inch internal hard drive bay4 Secondary 3.5-inch internal

Installing and removing drivesWhen installing drives, follow these guidelines:●The primary Serial ATA (SATA) hard drive must be connected to the dark

Removing a 5.25-inch driveNOTE: HP does not offer a 5.25-inch optical drive for this computer model. A 5.25-inch optical drive mayhave been installed

7. Press down on the green drivelock mechanism (1) and slide the drive from the drive bay (2).Installing a 5.25-inch driveNOTE: HP does not offer a 5.

7. If you are installing an optical drive, install four M3 metric mounting screws (not provided) in the lowerholes on each side of the drive.NOTE: Whe

9. Connect the power cable (1) and data cable (2) to the rear of the optical drive.10. Connect the opposite end of the data cable to one of the light

About This BookThis guide provides basic information for upgrading the HP EliteDesk Business PC.WARNING! Text set off in this manner indicates that fa

Removing a 9.5mm slim optical driveCAUTION: All removable media should be taken out of a drive before removing the drive from thecomputer.1. Remove/di

7. Push the green release lever on the right rear side of the drive toward the center of the drive (1), andthen slide the drive forward and out of the

7. Align the small pin on the release latch with the small hole on the side of the drive and press the latchfirmly onto the drive.8. Slide the optical

9. Connect the power cable (1) and data cable (2) to the rear of the optical drive.10. Connect the opposite end of the data cable to one of the light

Removing a 3.5-inch or 2.5-inch hard driveNOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so thatyou c

7. Remove the drive by pulling the release tab away from the drive (1) and sliding the drive out of the bay(2).8. Remove the four mounting screws (two

●If you are installing a 2.5-inch hard drive, install four black and blue M3 isolation mounting screws(two on each side of the drive).●You can also in

◦Secure the drive to the bay adapter bracket by installing four black M3 adapter bracketscrews through the sides of the bracket into the drive.Install

◦Install four 6-32 silver and blue isolation mounting screws in the adapter bracket (two oneach side of the bracket).7. Slide the drive into the drive

8. Connect the power cable (1) and data cable (2) to the back of the hard drive.NOTE: The power cable for the hard drives is a three-headed cable that

iv About This Book

Installing a security lockThe security locks displayed below and on the following pages can be used to secure the computer.Cable lockPadlock34 Chapter

HP Business PC Security Lock V21. Attach the security cable fastener to a desktop using the appropriate screws for your environment(screws not provide

3. Slide the security cable through the security cable fastener.4. Pull the two scissor hands of the monitor lock apart and insert the lock into the s

5. Slide the security cable through the security guide installed on the monitor.6. Attach the accessory cable fastener to a desktop using the appropri

7. Slide the security cable through the holes in the accessory cable fastener.8. Screw the lock to the chassis using the screw provided (1). Insert th

9. When you have completed all steps, all of the devices at your workstation will be secured.Installing a security lock 39

Front bezel securityThe front bezel can be locked in place by installing a security screw provided by HP. To install the securityscrew:1. Remove/disen

7. Install the security screw through the middle front bezel release tab to secure the front bezel in place.8. Replace the computer access panel.9. Re

A Battery replacementThe battery that comes with the computer provides power to the real-time clock. When replacing the battery,use a battery equivale

b. Slide the replacement battery into position, positive side up. The battery holder automaticallysecures the battery in the proper position.Type 2a.

Table of contents1 Product features ...

b. Insert the new battery and position the clip back into place.NOTE: After the battery has been replaced, use the following steps to complete this pr

B Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices

C Computer operating guidelines, routinecare and shipping preparationComputer operating guidelines and routine careFollow these guidelines to properly

Optical drive precautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation●Do not move the drive dur

D AccessibilityHP designs, produces, and markets products and services that can be used by everyone, including peoplewith disabilities, either on a st

IndexAaccess panelremoval 6replacement 7accessibility 48Bbattery replacement 42Ccomputer operating guidelines 46DDIMMs. See memorydrivescable connecti

Appendix B Electrostatic discharge ...

1 Product featuresStandard configuration featuresFeatures may vary depending on the model. For support assistance and to learn more about the hardware

Front panel componentsDrive configuration may vary by model. Some models have a bezel blank covering one or more drive bays.1 Hard Drive Activity Ligh

Rear panel components1 Power Cord Connector 7 PS/2 Mouse Connector (green)2PS/2 Keyboard Connector (purple) 8 Serial Connector3DisplayPort Monitor C