HP ProDesk 600 G2 Small Form Factor PC Manual de usuario

Hardware Reference GuideHP ProDesk 600 G2 SFF Business PC

Serial number locationEach computer has a unique serial number and a product ID number that are located on the exterior of thecomputer. Keep these num

2 Hardware upgradesServiceability featuresThe computer includes features that make it easy to upgrade and service. A Torx T15 or flathead screwdriveri

Removing the computer access panelTo access internal components, you must remove the access panel:1. Remove/disengage any security devices that prohib

Replacing the computer access panelSlide the tabs on the front end of the access panel under the lip on the front of the chassis (1), and then pressth

Removing the front bezel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact dis

Removing a slim optical drive bezel blankOn some models, there is a bezel blank covering the slim optical drive bay. Remove the bezel blank beforeinst

Replacing the front bezelInsert the four hooks on the bottom side of the bezel into the rectangular holes on the chassis (1), and thenrotate the top s

Changing from desktop to tower configurationThe Small Form Factor computer can be used in a tower orientation with an optional tower stand that can be

System board connectionsRefer to the following illustration and table to identify the system board connectors for your model.No. System Board Connecto

Installing additional memoryThe computer comes with double data rate 4 synchronous dynamic random access memory (DDR4-SDRAM)dual inline memory modules

© Copyright 2015 HP Development Company,L.P.Microsoft and Windows are U.S. registeredtrademarks of the Microsoft group ofcompanies.The information con

●The system will operate in flex mode if the total memory capacity of the DIMMs in Channel A is not equalto the total memory capacity of the DIMMs in

7. Open both latches of the memory module socket (1), and insert the memory module into the socket (2).NOTE: A memory module can be installed in only

Removing or installing an expansion cardThe computer has three PCI Express x1 expansion sockets and one PCI Express x16 expansion socket.NOTE: The PCI

a. If you are installing an expansion card in a vacant socket, remove the appropriate expansion slotcover on the back of the chassis. Pull the slot co

c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansionsocket away from the card and carefully rock the car

12. To install a new expansion card, hold the card just above the expansion socket on the system boardthen move the card toward the rear of the chassi

18. Lock any security devices that were disengaged when the access panel was removed.19. Reconfigure the computer, if necessary.Drive positions1 9.5mm

Installing and removing drivesWhen installing drives, follow these guidelines:●The primary Serial ATA (SATA) hard drive must be connected to the dark

Removing a 9.5mm slim optical driveCAUTION: All removable media should be taken out of a drive before removing the drive from thecomputer.1. Remove/di

Installing a 9.5mm slim optical drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such a

About This BookThis guide provides basic information for upgrading the HP ProDesk Business PC.WARNING! Text set off in this manner indicates that fail

9. Slide the optical drive through the front of the chassis all the way into the bay so that it locks in place(1), and then connect the power cable (2

Removing and replacing a primary 3.5-inch hard driveNOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so

8. Pull the release lever next to the rear of the hard drive outward (1). While pulling the release lever out,slide the drive back until it stops, and

10. Align the mounting screws with the slots on the chassis drive cage, press the hard drive down into thebay, and then slide it forward until it stop

Removing a secondary 3.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, suc

8. Disconnect the power cable (1) and data cable (2) from the rear of the hard drive. Press the release latchon the side of the drive cage (3), and th

Installing a secondary 3.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, s

8. Rotate the drive cage to its upright position.9. Slide the drive into the drive bay (1), and then connect the power cable (2) and data cable (3) to

10. Rotate the drive cage back down to its normal position.CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down.11.

Removing a 2.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compa

iv About This Book

8. Disconnect the power cable (1) and data cable (2) from the back of the hard drive.9. Pull outward on the release lever at the rear of the drive (1)

Installing a 2.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as com

8. Rotate the drive cage to its upright position.9. Align the mounting screws on the drive with the J-slots on the sides of the drive bay. Press the d

10. Connect the power cable (1) and data cable (2) to the back of the hard drive.NOTE: If the 2.5-inch hard drive is the primary drive, connect the ot

Installing a security lockThe security locks displayed below and on the following pages can be used to secure the computer.Cable lockPadlock38 Chapter

HP Business PC Security Lock V21. Attach the security cable fastener to a desktop using the appropriate screws for your environment(screws not provide

3. Slide the security cable through the security cable fastener.4. Pull the two scissor hands of the monitor lock apart and insert the lock into the s

5. Slide the security cable through the security guide installed on the monitor.6. Attach the accessory cable fastener to a desktop using the appropri

7. Slide the security cable through the holes in the accessory cable fastener.8. Screw the lock to the chassis using the screw provided (1). Insert th

9. When you have completed all steps, all of the devices at your workstation will be secured.Installing a security lock 43

Table of contents1 Product features ...

Front bezel securityThe front bezel can be locked in place by installing a security screw provided by HP. To install the securityscrew:1. Remove/disen

A Battery replacementThe battery installed on the computer provides power to the real-time clock. When replacing the battery, usea battery equivalent

7. Depending on the type of battery holder on the system board, complete the following instructions toreplace the battery.Type 1a. Lift the battery ou

b. Insert the new battery and position the clip back into place.NOTE: After the battery has been replaced, use the following steps to complete this pr

B Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices

C Computer operating guidelines, routinecare and shipping preparationComputer operating guidelines and routine careFollow these guidelines to properly

Optical drive precautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation●Do not move the drive dur

D AccessibilityHP designs, produces, and markets products and services that can be used by everyone, including peoplewith disabilities, either on a st

IndexAaccess panelremoval 6replacement 7accessibility 51Bbattery replacement 45Ccomputer operating guidelines 49DDIMMs. See memorydrivescable connecti

Cable lock ...

1 Product featuresStandard configuration featuresFeatures may vary depending on the model. For support assistance and to learn more about the hardware

Front panel componentsDrive configuration may vary by model. Some models have a bezel blank covering the slim optical drive bay.1 Slim Optical Drive (

Rear panel components1 PS/2 Mouse Connector (green) 7 PS/2 Keyboard Connector (purple)2Serial Connector 8 DisplayPort Monitor Connectors3RJ-45 Network