Hp Insight Management-Software Manual de usuario Pagina 28
- Pagina / 189
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Upgrading incompatible firmware modes and versions
If unsupported VC Domain firmware versions are detected at the end of a VCEM 7.2 upgrade, a
warning message similar to the following is displayed:
VCEM detected unsupported VC firmware. For information on how to upgrade
your firmware, run the Insight Software Advisor or refer to the VCEM
User Guide troubleshooting section.
Upgrade to a supported VC firmware by performing the following steps:
1. Select the VC Domain with an incompatible status and click VC Domain Maintenance.
2. Upgrade the managed VC Domains to the minimum VCEM supported VC firmware version.
See the “Mixed VC firmware versions and compatibility in a VC Domain Group ” (page 20)
for the VCEM-supported VC firmware versions.
3. Click Complete VC Domain Maintenance to close the operation.
4. Upgrade the VC Domain Group firmware mode to the minimum VCEM-supported VC firmware.
For more information, see “Upgrading VC Domain Group firmware mode” (page 83).
Installing VCEM in an HA-clustered CMS configuration in a Microsoft
Cluster Server cluster
VCEM can be installed in an HA clustered CMS configuration on an MSCS cluster. This installation
is described in Installing and Upgrading HP Insight Management 7.0 on Windows Server 2008
R2 Failover Clusters. This white paper is accessible in the HP Insight Management documentation
library at http://www.hp.com/go/insightmanagement/docs
By installing in a failover cluster configuration, the CMS can fail over to a backup cluster node if
the primary node needs maintenance or experiences a failure.
In preparation for a planned failover, ensure that no Insight Management jobs, tasks, requests, or
migration processes are running at the time of the failover. The configuration of the managed
environment should not be changed between powering off the CMS on the primary node and
resuming operations on the backup cluster node.
In the event of an unplanned failover, it is possible that manual intervention may be required to
restore full operations. If a VC Domain reports configuration mismatch or an out-of-sync occurrence
after recovering from an unplanned failover, the following actions are recommended.
• Execute Mxsync in analysis mode (mysync) to determine the nature of the failure on the VC
Domain during the CMS recovery phase.
• Execute Mxsync in execute mode (mxsync-e) during the CMS recovery phase, and follow
the Mxsync instructions until the VC Domains are synchronized.
• If Mxsync detects and reports out-of-sync scenarios in additional subsystems, resolve them
according to instructions displayed, otherwise exit Mxsync.
NOTE: Executing mxsync –e will help resolve VC Domain synchronization issues across multiple
VC domains.
28 Installing and configuring VCEM
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- 1 Introduction 9
- Platform support 10
- Product licensing 10
- Architectural overview 11
- 12 Introduction 12
- Managing HP Virtual Connect 13
- Understanding VCEM operations 13
- 14 Introduction 14
- 16 Introduction 16
- Installation prerequisites 20
- Installing VCEM 22
- Updating VC firmware 22
- Updating VC firmware 23 23
- Cluster Server cluster 28
- 3 Managing VC Domains 29
- 32 Managing VC Domains 32
- 34 Managing VC Domains 34
- ◦ Short (1 second) 35
- ◦ Long (30 second) 35
- 36 Managing VC Domains 36
- 38 Managing VC Domains 38
- Group with VC firmware 3.3x 39
- VC Domain tasks 40
- VCEM licensing 40
- Creating a VC Domain Group 41
- 42 Managing VC Domains 42
- 50 Managing VC Domains 50
- 52 Managing VC Domains 52
- VC Domain Maintenance 54
- VC Domain Maintenance 55 55
- 56 Managing VC Domains 56
- VC Domain Maintenance 57 57
- 58 Managing VC Domains 58
- VC Domain Maintenance 59 59
- 60 Managing VC Domains 60
- Viewing VC Domain details 61
- 62 Managing VC Domains 62
- VC Domain Maintenance 63 63
- 64 Managing VC Domains 64
- VC Domain Maintenance 65 65
- 66 Managing VC Domains 66
- VC Domain Maintenance 67 67
- SNMP Access 68
- Using VLAN capacity 69
- Maintenance 69
- 70 Managing VC Domains 70
- Using FlexFabric modules 71
- VCEM managed VC Domain 72
- Using FlexFabric modules 73 73
- 20-port FC module 74
- Connect FlexFabric module 75
- 76 Managing VC Domains 76
- Using FlexFabric modules 77 77
- 78 Managing VC Domains 78
- 4 Managing VC Domain groups 79
- Creating a VC Domain Group 81 81
- 82 Managing VC Domain groups 82
- Deleting a VC Domain Group 84
- 86 Managing VC Domain groups 86
- 88 Managing VC Domain groups 88
- Viewing VC Domain Group roles 89
- 90 Managing VC Domain groups 90
- Figure 54 LACP timer duration 92
- 94 Managing VC Domain groups 94
- 5 Managing server profiles 95
- Creating a server profile 98
- Creating a server profile 99 99
- 100 Managing server profiles 100
- Figure 60 iSCSI boot settings 101
- Creating a server profile 103 103
- 104 Managing server profiles 104
- Configuring multiple networks 105
- 106 Managing server profiles 106
- Deleting a server profile 107
- Editing a server profile 107
- 108 Managing server profiles 108
- 112 Managing server profiles 112
- Extending mapped networks 114
- Selecting a single network 115
- Selecting multiple networks 115
- Set option checked 115
- Assigning a server profile 116
- Unassigning a server profile 116
- Copying a server profile 117
- Moving a server profile 117
- 118 Managing server profiles 118
- Moving a server profile 119 119
- ◦ Under maintenance 120
- ◦ Expired license 120
- ◦ Incompatible firmware mode 120
- ◦ Incompatible firmware 121
- 122 Managing server profiles 122
- Using spare bays 124
- Handling 125
- 126 Managing server profiles 126
- Powering down a bay 128
- Powering down a bay 129 129
- Designating spare bays 130
- Failover” (page 124) 131
- MAC Addresses 132
- Creating MAC exclusion ranges 133
- Deleting MAC exclusion ranges 133
- WWN Addresses 135
- Creating WWN exclusion ranges 136
- Address management tasks 136
- Address management tasks 137 137
- EndStartMAC Exclusion ranges 139
- Address management tasks 139 139
- Deleting WWN exclusion ranges 141
- 4. Click OK 143
- 9 Tracking VCEM job status 145
- Reviewing job details 146
- Deleting jobs 146
- Preparation checklist 147
- Show CLI usage online help 153
- CLI exit and error codes 153
- 13 Troubleshooting VCEM 154
- VC 3.7x or later 155
- VCEM performance 156
- Server power management 157
- Server profile operations 157
- VC Profile Failover 157
- 158 Troubleshooting VCEM 158
- VC Domain 160
- 162 Troubleshooting VCEM 162
- 164 Troubleshooting VCEM 164
- 166 Troubleshooting VCEM 166
- Removing VCEM 167
- Backing up and restoring VCEM 167
- 168 Troubleshooting VCEM 168
- Replacing VC modules 170
- 172 Troubleshooting VCEM 172
- 174 Troubleshooting VCEM 174
- How to contact HP 175
- Subscription service 175
- HP authorized resellers 176
- Related information 176
- Typographic conventions 176
- Typographic conventions 177 177
- 15 Documentation feedback 178
- A VCEM subranges 179
- Glossary 183
- 184 Glossary 184
- 186 Glossary 186
- 188 Index 188
Relacionado con productos y manuales para Software Hp Insight Management-Software
Software Hp XC System 3.x Software Manual de usuario
(118 paginas)
(118 paginas)
Software Hp Insight Management Agents Manual de usuario
(175 paginas)
(175 paginas)
Software Hp Smart Update Manager Manual de usuario
(130 paginas)
(130 paginas)
Software Hp ProLiant Support Pack Manual de usuario
(44 paginas)
(44 paginas)
Software Hp SmartStart-Software Manual de usuario
(29 paginas)
(29 paginas)
Software Hp Access Control Manual de usuario
(14 paginas)
(14 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.478 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales