Hp Insight Management-Software Manual de usuario Pagina 52
- Pagina / 147
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9. Create a new VC Domain Group with the latest version of firmware in VCEM using this VC
Domain (with the HP Virtual Connect FlexFabric 10 Gb/24port module).
10. Reassign the existing Ethernet connections in the server profiles or add new connections to
the server profiles, depending on what was selected in Step 4.
11. Edit an existing server profile and add a network connection that uses the FlexFabric uplink
port.
12. Edit an existing server profile and an iSCSI connection and boot option that uses the FlexFabric
uplink port.
13. Create a new server profile and add a network connection that uses the FlexFabric uplink
port.
14. Create a new server profile and add a iSCSI connection and iSCSI boot that uses the FlexFabric
uplink port.
Replacing FC modules with FlexFabric modules in an existing VCEM managed VC
Domain
This scenario describes how to replace existing FC modules in bays three and four with VC-FC 4
Gb or VC-FC 8 Gb 24 port modules in an existing VC Domain. It also describes how to start using
FCoE functionality in existing or new server profiles.
1. Remove the VC Domain from the existing VC Domain Group.
2. Upgrade the VC Domain firmware to the latest version of VC firmware.
3. Replace the blade server FC HBA mezzanine cards with FlexFabric Adapter mezzanine cards.
4. Unassign any FC profile connections that are attached to the interconnect bays being replaced.
This can be done by unassigning the FC connections in the server profile. HP recommends
that you do this in order so you do not lose the MAC addresses.
5. Delete any FC SAN fabric connections that were created using uplinks from the interconnect
bays that are to be replaced.
6. Physically remove the FC modules from both horizontally adjacent bays three and four.
7. Add the two FlexFabric modules in both horizontally adjacent bays three and four with
appropriate FC SPF+ transceivers.
8. Recreate previously deleted FC SAN fabrics using FlexFabric uplink ports (X1 to X4) .
9. Create a new VC Domain Group with the latest version of VC firmware in VCEM and using
this VC Domain (with the HP Virtual Connect FlexFabric 10 Gb/24port module).
After performing all the steps in “Replacing FC modules with FlexFabric modules in an existing
VCEM managed VC Domain” (page 52) you can create, or edit any existing server profiles and
use the available networks or SAN Fabrics from the FlexFabric module to create FCoE or iSCSI
connections.
Replacing VC Ethernet and FC modules with FlexFabric modules in an existing VCEM
managed VC Domain
This scenario describes how to replace existing VC-Ethernet 10/10 Gb-F modules in bays one and
two and VC-FC 4 Gb or VC-FC 8 Gb 24 port modules in bays three, four, five and six . It also
describes how to start using FlexFabric functionality in existing or new server profiles.
1. Remove the VC Domain from the existing VC Domain Group.
2. Upgrade the VC Domain firmware to the latest version of VC firmware.
3. Save the configuration.
4. Unassign any Flex-10 NICs with profile connections that are attached to the interconnect bays
being upgraded. This can be done by unassigning the Ethernet connections in the server
profile. HP recommends that you do this in order so you do not lose the MAC addresses.
5. Delete any existing Ethernet network connections that were created using uplinks from the
interconnect bays that are to be replaced.
52 Managing VC Domains
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 1 Introduction 8
- Platform support 9
- Product licensing 9
- Architectural overview 10
- Architectural overview 11 11
- Managing HP Virtual Connect 12
- Understanding VCEM operations 12
- 14 Introduction 14
- Installation prerequisites 15
- Installing VCEM 17
- Updating VC firmware 18
- Updating VC firmware 19 19
- Cluster Server cluster 23
- 3 Managing VC Domains 24
- 28 Managing VC Domains 28
- 30 Managing VC Domains 30
- 32 Managing VC Domains 32
- VC Domain tasks 33
- VCEM licensing 33
- Creating a VC Domain Group 34
- Creating a VC Domain Group 35 35
- 38 Managing VC Domains 38
- 40 Managing VC Domains 40
- VC Domain Maintenance 42
- VC Domain Maintenance 43 43
- 44 Managing VC Domains 44
- VC Domain Maintenance 45 45
- 46 Managing VC Domains 46
- VC Domain Maintenance 47 47
- Using VLAN capacity 48
- Maintenance 49
- Using FlexFabric modules 50
- VCEM managed VC Domain 51
- 52 Managing VC Domains 52
- 4 Managing VC Domain groups 54
- 56 Managing VC Domain groups 56
- 58 Managing VC Domain groups 58
- Deleting a VC Domain Group 59
- 60 Managing VC Domain groups 60
- 62 Managing VC Domain groups 62
- 5 Managing server profiles 63
- Creating a server profile 65
- 66 Managing server profiles 66
- Creating a server profile 67 67
- Figure 29 iSCSI boot settings 68
- 70 Managing server profiles 70
- Configuring multiple networks 72
- Deleting a server profile 74
- Editing a server profile 74
- Server profile 76
- 76 Managing server profiles 76
- 78 Managing server profiles 78
- Extending mapped networks 80
- Selecting a single network 81
- Selecting multiple networks 81
- Set option checked 81
- Assigning a server profile 82
- Unassigning a server profile 82
- Copying a server profile 83
- Moving a server profile 83
- 84 Managing server profiles 84
- Moving a server profile 85 85
- ◦ Under maintenance 86
- ◦ Expired license 86
- ◦ Incompatible firmware mode 86
- ◦ Incompatible firmware 87
- 88 Managing server profiles 88
- Using spare bays 90
- Handling 91
- 92 Managing server profiles 92
- Powering down a bay 94
- Powering down a bay 95 95
- Designating spare bays 96
- Failover” (page 90) 97
- MAC Addresses 98
- Creating MAC exclusion ranges 99
- Deleting MAC exclusion ranges 99
- WWN Addresses 101
- Creating WWN exclusion ranges 102
- Address management tasks 102
- Address management tasks 103 103
- Deleting WWN exclusion ranges 105
- 9 Tracking VCEM job status 108
- Deleting jobs 109
- Reviewing job details 109
- Preparation checklist 110
- Show CLI usage online help 116
- CLI exit and error codes 116
- 13 Troubleshooting VCEM 117
- VCEM performance 118
- Jobs 119 119
- 120 Troubleshooting VCEM 120
- VC Domain 122
- 124 Troubleshooting VCEM 124
- 126 Troubleshooting VCEM 126
- 128 Troubleshooting VCEM 128
- Removing VCEM 129
- Backing up and restoring VCEM 129
- 130 Troubleshooting VCEM 130
- Replacing VC modules 132
- Read timed out 133
- Maintenance operation fails 134
- 136 Troubleshooting VCEM 136
- Contacting HP 138
- Related information 139
- Typographic conventions 139
- Glossary 141
- 142 Glossary 142
- 144 Glossary 144
- 146 Index 146
Relacionado con productos y manuales para Software Hp Insight Management-Software
Software Hp Insight Management Agents Manual de usuario
(157 paginas)
(157 paginas)
Software Hp Access Control Manual de usuario
(22 paginas)
(22 paginas)
Software Hp Insight Management Agents Manual de usuario
(165 paginas)
(165 paginas)
Software Hp SmartStart-Software Manual de usuario
(59 paginas)
(59 paginas)
Software Hp Software SmartStart HP Manual de usuario
(37 paginas)
(37 paginas)
(120 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.358 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales