Hp Integrity rx4610 Server Manual de usuario Pagina 137
- Pagina / 201
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 11: Troubleshooting
130
Table 11-1. BMC Beep Codes
Code
Description
1-5-1-1 FRB failure (processor failure)
1-5-2-1 No processors installed/detected
1-5-4-2 Power control fault. Power-good dropped out. This
beep code occurs during run time
1-5-4-4 PWRGD-BUF failure. System did not assert power-
good on power-up. Check installed D2D
configuration, verify processors seated, processor
power pods are connected, and Legacy cable
connector is secure with no bent pins. This beep
code ouccrs during system power on.
1-5-5-1 CPU board interlock failure. Verify CPU board
inserted fully.
1-5-4-2
OR
1-5-4-4
1 Power Supply Configuration Failed to retain 3+1
redundancy (1 Redundant)
2-1 Processor1 Power Good failed due to power pod
failure or not connected to 48V
2-2 Processor2 Power Good failed due to power pod
failure or not connected to 48V
2-3 Processor3 Power Good failed due to power pod
failure or not connected to 48V
2-4 Processor4 Power Good failed due to power pod
failure or not connected to 48V
3-1 Upper Memory board power good failed.
3-1 Lower Memory board power good failed.
4 12V D2D Power Good failure.
5-1 I/O 5V A D2D Power Good failure.
5-2 I/O 5V B D2D Power Good failure.
6 PROC 3.3V D2D Power Good failure.
7-1 I/O 3.3V A D2D Power Good failure.
7-2 I/O 3.3V B D2D Power Good failure.
8-1 1.8V D2D Power Good failure (processor board
only).
Beep Code for 1-5-1-1 & 1 for Power Supply Configuration Failed to retain 3+1 redundancy
300Ms
600Ms
3Sec
600Ms 600Ms
300Ms
- User Guide 1
- Audience Assumptions 2
- Contents 3
- Open/Close Button 10
- LCD DISPLAY 11
- • +48 V 13
- • +12 V standby 13
- Rear View 14
- Legacy I/O Panel 15
- Powering-Up the HP Server 17
- Powering-Down the HP Server 17
- Mounting the Front Bezel 19
- Main Cover 21
- Replacing the Top Cover 22
- Tools and Supplies Needed 24
- Removing the 172 mm Fans 25
- Hot Swapping the 120 mm Fans 26
- Installing the 120 mm Fans 27
- If only 3 power supplies 28
- Removing a Power Supply 30
- Installing a Power Supply 31
- Mass Storage Guidelines 32
- Tools Required 33
- Determining Drive Status 34
- Removing a Hard Disk Drive 34
- Installing the DVD Drive 37
- Removing the Hard Disk Bay 39
- Installing the Hard Disk Bay 40
- Removing the SCSI Backplane 41
- 1. Disconnect the cable 42
- 2. Remove the two screws 42
- Removing Memory Boards 46
- Installing Memory Boards 47
- Installing DIMMs 49
- Removing DIMMs 51
- Removing a Processor 58
- Figure 6-7. The Triple Beam 62
- Installing Accessory Boards 65
- PCI Hot Plug Slots 68
- Non PCI Hot Plug Slots 68
- Removing Accessory Boards 70
- 8 Server Management Boards 72
- Hot Swap Controller (HSC) 73
- Sideplane cover 75
- Remove protective 75
- Installing the I/O Baseboard 77
- Sideplane Board 78
- PCI Hot Plug LED Board 79
- Legacy I/O Board 81
- Server Management 82
- DVD Cable 82
- Floppy Disk 82
- Drive Cable 82
- Chapter 8: Server Management 83
- Configuring the HP Server 93
- Accelerated Cool Down 100
- FRB3 Timeout 101
- Using BIOS Setup 106
- Using the SELViewer Utility 114
- Using the SDR Viewer Utility 119
- Server Firmware 122
- 11 Troubleshooting 123
- Introduction 123
- Common Installation Problems 123
- Chapter 11: Troubleshooting 125
- BIOS Error Codes\Messages 132
- Beep Codes 136
- Table 11-1. BMC Beep Codes 137
- Types of Memory Tests 138
- User Notification 139
- User Action 139
- Base Memory Test 141
- Error Logging 143
- Extended Memory Test 147
- Examples 149
- Memory Test Duration 150
- Aborting the Memory Test 151
- Setup Dialog 152
- DIMMUTIL 155
- 12 Parts Information 156
- Replaceable Parts List 162
- Parts List Identifier 162
- Appendix A Specifications 165
- Appendix A: Specifications 166
- Video Display Modes 167
- VGA Video Port 168
- Keyboard and Mouse 169
- Parallel Port 170
- Serial Ports A and B 170
- Universal Serial Bus (USB) 172
- Figure A-7. SCSI Connector 173
- Figure A-8. IDE Connector 174
- Information on Jumpers 178
- Legacy I/O Board Jumpers 184
- J7A1 J7A1 186
- I/O Baseboard Jumpers 188
- J8D1 J8D1 189
- Determining DC-to-DC Status 191
- Equipment Log 193
- BMC, 129, 130 195
- Fan Fail LED, 2 196
- Front Panel LCD, 2 197
- General Fault LED, 2 197
- INIT, 2 197
- Index 198
- Power Fail LED, 2 199
- Power On/Off, 2 199
- Reset, 2 199
- Speaker, 129 200
- System Power LED, 2 200
Relacionado con productos y manuales para Hardware De La Computadora Hp Integrity rx4610 Server
(144 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales