Hp ProLiant DL160 Gen8 Server Manual de usuario Pagina 29
- Pagina / 109
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Setup 29
To install the component:
1. Install the server and cable management arm into the rack. See the installation instructions that ship with
the Quick Deploy Rail System.
2. Connect peripheral devices to the server.
3. Connect the power cord to the server.
4. Using the strain relief clip from the server hardware kit, secure the power cord.
5. Connect the power cord to the power source.
6. Power up the server (on page 16).
Installing the operating system
This HP ProLiant server does not ship with provisioning media. Everything needed to manage and install the
system software and firmware is preloaded on the server.
To operate properly, the server must have a supported operating system. For the latest information on
operating system support, see the HP website (http://www.hp.com/go/supportos).
To install an operating system on the server, use one of the following methods:
• Intelligent Provisioning—The iLO Management Engine is a new feature on ProLiant servers that contains
Intelligent Provisioning for embedded deployment, updating, and provisioning capabilities. Intelligent
Provisioning can configure the server and install an operating system, eliminating the need for
SmartStart CDs and Smart Update Firmware DVDs.
To install an operating system on the server with Intelligent Provisioning (local or remote):
a. Connect the Ethernet cable between the network connector on the server and a network jack.
b. Press the Power On/Standby button.
c. During server POST, press the F10 key.
d. Complete the initial Preferences and Registration portion of Intelligent Provisioning (on page 76).
e. At the 1 Start screen, click the Configure and Install button.
f. To finish the installation, follow the onscreen prompts. An Internet connection is required to update
the firmware and systems software.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- Rear panel components 8
- System board components 9
- DIMM slots 10
- System maintenance switch 10
- Drive numbering 11
- Drive LED definitions 12
- FBWC module LED definitions 12
- Fan modules 14
- Component identification 15 15
- Operations 16
- Operations 18 18
- Remove the access panel 19
- Install the access panel 19
- Remove the PCI riser cage 21
- Install the PCI riser cage 22
- Operations 23 23
- Rack planning resources 24
- Optimum environment 24
- Temperature requirements 25
- Server warnings and cautions 26
- Rack warnings 27
- Installing hardware options 28
- Registering the server 30
- Introduction 31
- Security bezel option 31
- Drive options 31
- Installing a hot-plug drive 32
- Mini-SAS cable option 34
- VGA power cable option 36
- Controller options 38
- 8. Do one of the following: 40
- Optical drive option 42
- SFF configuration 43
- Memory options 45
- HP SmartMemory 47
- DIMM identification 47
- Memory protection modes 48
- Memory population guidelines 49
- Installing a DIMM 51
- Expansion board options 61
- FlexibleLOM option 63
- Cabling 67
- SFF drive cabling 69
- Power cabling 70
- Cable number Description 71
- Maximum configuration 71
- FBWC capacitor pack cabling 72
- Front panel cabling 72
- Internal USB cabling 73
- Server mode 74
- HP product QuickSpecs 74
- HP iLO Management Engine 74
- Active Health System 75
- Intelligent Provisioning 76
- HP Insight Diagnostics 77
- Erase Utility 77
- HP Service Pack for ProLiant 78
- HP ROM-Based Setup Utility 79
- Using RBSU 80
- Auto-configuration process 80
- Boot options 81
- Configuring AMP modes 81
- Utilities and features 82
- ROMPaq utility 83
- Automatic Server Recovery 83
- USB support 83
- Keeping the system current 84
- Software and firmware 85
- Version control 85
- ProLiant servers 85
- Troubleshooting 86
- System battery replacement 87
- Regulatory information 89
- Electrostatic discharge 90
- Specifications 91
- Specification Value 92
- Power supply calculations 94
- Support and other resources 95
- Customer Self Repair 97
- Reparo feito pelo cliente 99
- Acronyms and abbreviations 103
- Documentation feedback 106
- Index 107 107
- Index 108 108
- Index 109 109
Relacionado con productos y manuales para Hardware De La Computadora Hp ProLiant DL160 Gen8 Server
(57 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales