HP 181A Manual de usuario Pagina 56
- Pagina / 254
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 1 Performance Tests
Test 5: Option 030/050/124 Channel 3 Frequency Sensitivity (HP
53131A/132A Only)
1-34 Assembly-Level Service Guide
1
200 MHz to 12.4 GHz Sensitivity for HP 53131A/132A
(Option 124 only)
1 Connect the 8340B Sweep Oscillator to Channel 3 of the counter.
2 Change the settings of the Sweep Oscillator to 12.4 GHz,
−
40 dBm.
3 Increase the power level in 1 dB steps until the Counter displays a
stable reading of approximately 12.4 GHz.
The Counter should display 12.4 GHz at
≤ −
23 dBm.
NOTE
Use a power meter and sensor to ensure the accuracy of the power being
input.
4 Sweep the frequencies from 200 MHz to 12.4 GHz.
The Counter should read frequencies from 200 MHz to 12.4 GHz
at
≤−
3dBm.
5 Record the actual reading in the Performance Test Record
(Test 5, Line 4).
6 Disconnect the test setup.
- HP 53131A/132A/181A 1
- 225 MHz Counter 1
- Assembly-Level Service 3
- THUS, NEVER TRY 4
- TO MEASURE AC POWER 4
- LINE SIGNALS WITHOUT AN 4
- ISOLATION TRANSFORMER 4
- 2 Service 9
- Contents 10
- 3 Replacing Assemblies 11
- 4 Retrofitting Options 12
- 5 Replaceable Parts 12
- 6 Backdating 13
- 8 HP 53181A Specifications 13
- How to Use This Guide 15
- How to Order Guides 17
- Hardware 20
- Accessories Supplied 21
- Accessories Available 21
- Performance Tests 23
- Complete Performance Tests 25
- Optional HP-IB Verification 25
- Recommended Calibration Cycle 25
- Test Record 25
- Equipment Required 26
- Verification 27
- HP 3458A 30
- Digital Multimeter 30
- Counter Setup 32
- HP 8663A 33
- Synthesized Signal Generator 33
- External Timebase Tests 34
- HP 3325B 35
- Synthesizer #1 35
- Synthesizer #2 35
- HP53131A/132 40
- Synthesizer 42
- FREQUENCY 2 46
- Frequency 1 47
- Frequency 2 48
- (HP 53131A/132A Only) 49
- Option 030 only 53
- (Option 050 only) 55
- (Option 124 only) 56
- Volt Peak 2 61
- (Optional) 62
- (Page 1 of 6) 63
- (Page 2 of 6) 64
- (Page 3 of 6) 65
- (Page 4 of 6) 66
- (Page 5 of 6) 67
- (Page 6 of 6) 68
- (HP 53181A Only) 73
- Frequency Sensitivity 80
- 030/050/124 87
- (Page 1 of 4) 93
- (Page 2 of 4) 94
- (Page 3 of 4) 95
- (Page 4 of 4) 96
- To Provide Repair Information 99
- Scale & 102
- On / Stby 102
- key, then press POWER 104
- To Unsecure for Calibration 105
- To Secure Against Calibration 109
- To View the Calibration Count 110
- Channels 1 and 2 111
- key, then press POWER key 111
- CALIBRATING 113
- OFFS 1 PASS 113
- CAL: OFFS 2 ? 113
- OFFS 2 PASS 113
- DC Power Supply 114
- HP 53131A/132A 114
- Counter Digital Multimeter 114
- To Calibrate Time Interval 115
- HP53131A/132A 116
- HP 8130A 116
- Pulse Generator 116
- CAL: TI FINE? Calibration 117
- Equipment 117
- CAL: TI FINE? 118
- TI CAL PASS 118
- House Standard 119
- 10 MHz Reference 119
- (Medium, High, or Ultra-High) 120
- Chapter 2 Service 123
- Channel 1 127
- CAL: GAIN 1 ? 129
- GAIN 1 PASS 129
- HP 53181A 130
- Safety Considerations 132
- Recommended Test Equipment 133
- Repair Considerations 134
- After Service Considerations 135
- Troubleshooting the Counter 141
- Motherboard 142
- Assembly 142
- TEST LOOP: ON 143
- Self Tests 145
- Replacing Assemblies 149
- Introduction 150
- Tools Required 151
- Do This First 151
- To Remove the Cover 152
- SERIAL PLATE 153
- To Remove the Front Bezel 154
- Rubber foot 164
- A4 AC Power 164
- Supply Assembly 164
- (Option 002) 165
- FOR LABORATORY USE BY 168
- QUALIFIED PERSONNEL 168
- FOUR USAGE EN LABORATOIRE 168
- PAR PERSONNEL QUALIFIE 168
- Talk Only 168
- Retrofitting Options 173
- Retrofitting Procedure 177
- Cable wires 182
- Procedure 184
- A6 High Stability 185
- Timebase Assembly 185
- Plug (MP9) 187
- Replaceable Parts 191
- Exchange Assemblies 192
- Reference Designations 193
- How To Order A Part 194
- Contacting Hewlett-Packard 195
- Cabinet Parts and Hardware 196
- Chapter 5 Replaceable Parts 197
- Assemblies) 199
- Backdating 201
- Manual Changes 202
- Older Instruments 202
- Backdating Hardware 203
- CHANGE 3 (New TCXO boards) 204
- Option 002 206
- Option 015 206
- Option 030 206
- Option 050 206
- Backdating Firmware 208
- (Continued) 209
- HP53131A 213
- (Medium or High) 215
- Backdating Specifications 216
- Chapter 6 Backdating 218
- HP 53131A/132A Specifications 219
- Instrument Inputs 220
- Instrument Inputs (Continued) 221
- Time Base 222
- Measurement Specifications 223
- Automatic or External Arming: 224
- Time or Digit Arming: 224
- Time Interval 227
- Frequency Ratio: 227
- Pulse Width 228
- Rise/Fall Time 228
- Duty Cycle 229
- Totalize 229
- Peak Volts 229
- Trigger Level Timing Errors 230
- Gate Time 232
- Measurement Throughput 232
- Measurement Arming 232
- Measurement Statistics 233
- Measurement Limits 233
- General Information 234
- HP 53181A Specifications 235
- Input Frequency (Hz) 240
- Frequency Error (Hz) 240
- Input Frequency 240
- Measurement Definitions 243
- NUMERICS 247
- 1-800-800-5281 251
- 254
Relacionado con productos y manuales para Multímetros HP 181A
Multímetros HP 1GSa/s Manual de usuario
(90 paginas)
(90 paginas)
Multímetros HP Weather Radio C Manual de usuario
(37 paginas)
(37 paginas)
Multímetros HP MPEGscope Manual de usuario
(44 paginas)
(44 paginas)
Multímetros HP 34970A Manual de usuario
(429 paginas)
(429 paginas)
Multímetros HP 6205B Manual de usuario
(68 paginas)
(68 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales