HP X Unified Security Platform Series Manual de usuario Pagina 227
- Pagina / 333
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
L2TP Configuration
X Family LSM User’s Guide V 2.5.1 211
L2TP Configuration
Enable L2TP Server and Configure L2TP Client and Addresses
Enable L2TP Server and Configure L2TP Client and Addresses
STEP 1
If you are not using RADIUS to assign IP addresses, create an IP address group (Network >
Configuration > IP Address Groups) containing the pool of IP addresses that the X family
device will use to allocate IP addresses to L2TP VPN clients.
STEP 2
From the LSM menu, select VPN > L2TP Status. Then click the L2TP Server Configuration
tab.
STEP 3
On the L2TP Server Configuration page, check Enable L2TP Server.
This allows VPN clients to use the X family as a VPN terminator for L2TP.
STEP 4
Select the remote security zone on which to terminate the VPN from the L2TP security zone
drop-down list.
STEP 5
To use Microsoft Point-to-Point Encryption, check Require encryption.
This option provides additional security, and is supported by Windows VPN clients.
STEP 6
To use Microsoft Networking, enter the IP addresses of your primary and secondary WINS
servers in the WINS Server 1 and WINS Server 2 fields respectively.
WINS Servers If you are using Microsoft Networking, type the IP addresses of your primary
(WINS Server 1) and secondary (WINS Server 2) WINS servers.
DNS Servers Determines the DNS severs that the PPTP Server uses:
• Select Device Acts as DNS Relay to enable the X family device to act a proxy-
DNS server (DNS relay), passing DNS queries to its configured DNS servers.
• Select Specify DNS Server to enter up to two local DNS server IP addresses, in
order in which they are to be accessed, in the DNS Server fields.
L2TP
Addresses
Determines how IP addresses are allocated to clients connected through the
L2TP server:
• Select IP address assigned by RADIUS to enable the X family device to use
the RADIUS server to assign the L2TP client IP address. The RADIUS server
must be enabled on the RADIUS page (Authentication > RADIUS).
• Specify IP Address Group and select an existing address group to enable the X
family device to assign the L2TP client an IP address from the addresses
included in the IP Address group. Use the IP Addresses page (Network >
Configuration > IP Address Groups) to create IP Address Groups.
Table 7–7: L2TP Server Configuration Parameters
Parameter Description
- X Family 1
- Local Security Manager 1
- User’s Guide 1
- 3Com Corporation 2
- 350 Campus Drive 2
- Marlborough, MA 01752 2
- Chapter 3. IPS Filtering 15 4
- Chapter 4. Firewall 63 4
- Chapter 6. Network 129 6
- Chapter 7. VPN 181 7
- Chapter 8. System 217 7
- Glossary 307 9
- Index 315 9
- Contents 10
- About This Guide 11
- Conventions 12
- Screen Captures 13
- Messages 13
- Related Documentation 14
- Customer Support 14
- Contact Information 15
- System Overview 17
- Core Functionality 18
- X Family Environment 19
- Local Clients 20
- System Requirements 20
- SMS Configuration 20
- LSM Navigation 21
- Logging In 22
- Logging In 23
- Figure 2–1: LSM Logon Page 23
- LSM Screen Layout 24
- Main Menu Bar 25
- Navigation 26
- Content and Functionality 27
- System Summary 28
- Log Summary 29
- Product Specifications 30
- IPS Filtering 31
- Using the IPS 32
- Security Profiles 33
- Chapter 3 IPS Filtering 34
- Managing Security Profiles 35
- Security Profile Details 36
- Security Profiles 37
- Filter Components 40
- Configuring DV Filters 41
- View DV Filters 42
- Filter Search 43
- Filters List (All Filters) 43
- Filter List Details 44
- Address 50
- Reset an Individual Filter 51
- Port Scan/Host Sweep Filters 51
- Filter Tuning 52
- Traffic Threshold Filters 54
- Traffic Threshold Details 55
- Column Definition 56
- Traffic Threshold Filters 57
- Action Sets 60
- Action Set Configurations 61
- Default Action Sets 62
- Managing Actions 63
- Rate Limit Action Set 65
- Quarantine Action Set 65
- Action Sets 67
- Notification Contacts 68
- Notification Contacts 69
- IPS Services 71
- IPS Services Page Details 72
- Preferences 75
- Adaptive Filter Configuration 76
- Click Apply 77
- Firewall 79
- Chapter 4 Firewall 80
- Default Firewall Rules 83
- Managing Firewall Rules 84
- Firewall Rules List Details 85
- Configuring Firewall Rules 87
- Configuration Notes 88
- Firewall Services 91
- Configuring Service Groups 94
- Schedules 95
- Managing Schedules 97
- Virtual Servers 98
- Virtual Servers page 99
- Configuring Virtual Servers 100
- Web Filtering 101
- How Web Filtering Works 102
- Setting Up Web Filtering 103
- Web Filtering Page 104
- Web Filtering 105
- Parameter Description 105
- Web Filter Service 106
- Custom Filter List 108
- Parameter/Function 109
- Configure URL Patterns 110
- Value Description 111
- URL Test 112
- Events: Logs, Traffic 113
- Streams, Reports 113
- Overview 114
- Alert Log 115
- Audit Log 116
- IPS Block Log 117
- Firewall Block Log 118
- Firewall Session Log 119
- Configuration 120
- System Log 121
- Managing Logs 122
- Viewing Logs 123
- Downloading a Log 123
- Resetting a log 124
- Searching a Log 125
- Managed Streams 126
- Managed Streams 127
- Field Description 127
- Rate Limited Streams 128
- Quarantined Addresses 129
- Column Description 130
- • Performance/Throughput 132
- Device Health 133
- Module Health 134
- Table 5–13: Module Health 135
- Performance/Throughput 136
- Port Health 136
- Reports 137
- Attack Reports 138
- Rate Limit Reports 139
- Traffic Reports 139
- Update report data 140
- Traffic Threshold Report 141
- Quarantine Report 141
- Firewall Reports 142
- Configuration Overview 146
- Deployment Modes 147
- Network Port Configuration 148
- Port Configuration Tasks 149
- Chapter 6 Network 150
- Security Zone Configuration 151
- Preconfigured Zones Ports 152
- Security Zone Configuration 153
- IP Interfaces 156
- Managing IP Interfaces 157
- IP Interfaces 159
- Configuring a GRE Tunnel 164
- Bridge Mode for IP Interfaces 166
- RIP for IP Interfaces 166
- RIPv1 Configuration Settings 167
- RIPv2 Configuration Settings 167
- IP Address Groups 169
- Default Gateway 172
- Routing Table 173
- Static Routes 175
- RIP Setup 176
- Routing 177
- Multicast (IGMP and PIM-DM) 179
- PIM-DM Setup 181
- DHCP Server 183
- DHCP Server Page 184
- Configure DHCP Server 185
- DHCP Relay 187
- Configuring DHCP Relay 188
- Static Reservations 190
- Network Tools 192
- DNS Lookup 193
- Find Network Path 193
- Traffic Capture 193
- Traceroute 195
- About VPN 198
- VPN Configuration Overview 199
- IPSec Configuration 200
- IPSec Status Details 201
- Chapter 7 VPN 202
- IPSec Configuration 205
- IKE Proposal 214
- IKE Proposal Details 215
- Configuring IKE Proposals 216
- IKE Proposal 217
- L2TP Configuration 224
- L2TP Status Page Details 225
- L2TP Server Configuration 226
- L2TP Configuration 227
- PPTP Configuration 228
- PPTP Server Configuration 229
- PPTP Configuration 231
- Chapter 8 System 234
- Persistent Settings 236
- Updating the TOS Software 240
- System Snapshots 243
- Time Options 245
- Figure 8–3: Time Options Page 246
- Internal CMOS Clock 247
- NTP Server 247
- Time Zones 248
- SMS/NMS 249
- High Availability 251
- How High Availability Works 252
- Email Server 257
- Syslog Servers 258
- Setup Wizard 258
- Authentication 261
- User List 262
- TOS and Local User Accounts 263
- TOS User Security Level 263
- Managing User Accounts 265
- Chapter 9 Authentication 268
- Privilege Groups 269
- X.509 Certificates 271
- CA Certificates 273
- Certificate Requests 276
- Managing Certificate Requests 278
- Local Certificates 279
- Preferences 282
- Preferences Parameter Details 283
- Browser Certificates 287
- Client Authentication Message 288
- Security Alert 289
- Certificate Authority 290
- Security Alert 291
- Invalid Certificate Name 293
- Figure A–11: HOSTS File 294
- Core Categories 298
- Gambling 299
- Hate Speech 299
- Violence 299
- Productivity Categories 300
- Advertisement 301
- Arts & Entertainment 301
- Computing & Internet 301
- Education 301
- Appendix B Web Filter Service 302
- Free 14-day Trial Period 306
- Log Formats and System 307
- Log Formats 308
- Audit Log Format 310
- Field Name Description 311
- Firewall Block Log Format 312
- Firewall Session Log Format 314
- VPN Log Format 315
- System Log Format 316
- Remote Syslog Log Format 317
- System Update Status Messages 319
- Device Maximum 321
- Parameter X5 X506 322
- Glossary 323
- X family device 328
Relacionado con productos y manuales para Redes HP X Unified Security Platform Series
Redes HP N1200 Manual de usuario
(198 paginas)
(198 paginas)
Redes HP 100Base-T Manual de instalación
(20 paginas)
(20 paginas)
(176 paginas)
Redes HP 8800 Router Series Manual de instalación
(121 paginas)
(121 paginas)
Redes HP Cooktop 10GBE Manual de usuario
(34 paginas)
(34 paginas)
Redes HP -PB 10 Manual de usuario
(112 paginas)
(112 paginas)
Redes HP 3PAR Guía de usuario
(53 paginas)
(53 paginas)
Redes HP U522 Manual de usuario
(44 paginas)
(44 paginas)
Redes HP 9200c Manual de usuario
(218 paginas)
(218 paginas)
Redes HP 480-0005-00-15 Manual de usuario
(185 paginas)
(185 paginas)
Redes HP 100VG-ANYLAN B5426-90001 Manual de usuario
(39 paginas)
(39 paginas)
Redes HP DT-10 Manual de usuario
(20 paginas)
(20 paginas)
Redes HP AD583C Manual de usuario
(132 paginas)
(132 paginas)
Redes HP E5000 Guía de inicio rápido
(2 paginas)
(2 paginas)
Redes HP Cloud OS for Moonshot Guía de usuario
(126 paginas)
(126 paginas)
Redes HP hn220w Manual de inicio rápido
(12 paginas)
(12 paginas)
Redes HP ActivCard Smart Card Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales