HP T1000 Guía de usuario

HP UPS T1000/1500 User Guide April 2006 (First Edition) Part Number 404317-001a

Component identification 10 UPS T1000 INTL rear panel Item Description 1 Voltage configuration DIP switches 2 Serial communications port 3

Component identification 11 UPS T1500 INTL rear panel Item Description 1 Voltage configuration DIP switches 2 Serial communications port 3

Installation 12 Installation In this section Precautions...

Installation 13 Checking the battery recharge date Before unpacking the UPS, check the date on the battery recharge date label that is affixed to the

Installation 14 2. Connect the negative (black) lead to the negative battery terminal. NOTE: A small amount of arcing may occur when connecting t

Installation 15 Output voltage Input voltage range DIP switch 2 DIP switch 1 T1000/1500 NA/JPN/TWN 100 V* (JPN/TWN) 90–106 V Down Up 110 V 99

Installation 16 Connecting the USB communications port CAUTION: Using a USB to serial converter cable will damage the UPS. Connecting the Networ

Installation 17 Connecting the UPS to utility power WARNING: To prevent injury from electric shock or damage to the equipment: • Plug the input l

Installation 18 Powering up the UPS Press and hold the Power On/Standby button (1) until the UPS beeps. The Power LED illuminates solid green, indica

UPS operations 19 UPS operations In this section Initiating a self-test...

© Copyright 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties

UPS operations 20 4. Wait at least 60 seconds for the UPS internal circuitry to discharge.

Power management 21 Power management In this section HP Power Manager features...

Maintenance 22 Maintenance In this section Updating the UPS firmware ...

Maintenance 23 • Minimize the amount of time the UPS uses battery power by matching the UPS configuration with the utility voltage. See "Selecti

Maintenance 24 4. Disconnect the negative (black) lead.

Maintenance 25 5. Remove the battery module.

Maintenance 26 6. Disconnect the positive (red) lead. To replace the component, reverse the removal procedure. IMPORTANT: Charge the batteries f

Maintenance 27 4. Neutralize spilled battery acid with the special solutions contained in a spill kit or with a solution of 1 lb baking soda to 1 gal

Troubleshooting 28 Troubleshooting In this section UPS does not start ...

Troubleshooting 29 UPS frequently switches between utility and battery power Action: 1. Check the input voltage and reconfigure the UPS ("Selec

Contents 3 Contents Component identification...

Troubleshooting 30 Output Load Level LED is red or flashing red Action: 1. Remove one or more load devices to reduce the power requirements. 2. I

Specifications 31 Specifications In this section T1000 physical specifications...

Specifications 32 UPS model Utility voltage frequency (Hz) Available settings utility voltage (VAC) Branch circuit rating (A) Line cord T1000/15

Specifications 33 Configuration setting (VAC) Available nominal output voltage (VAC) 230 230 240 240 Output tolerance specifications Source of

Specifications 34 Feature Specification Operating altitude Up to 2,000 m (6,600 ft) above sea level Nonoperating altitude Up to 15,000 m (49,212 ft

Spares 35 Spares In this section Ordering spares...

Technical support 36 Technical support In this section Before you contact HP...

Warranty information 37 Warranty information In this section Limited warranty ...

Warranty information 38 • Notification from power management software

Regulatory compliance notices 39 Regulatory compliance notices In this section Regulatory compliance identification numbers...

Contents 4 Site Wiring Fault LED is red ...

Regulatory compliance notices 40 Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device,

Regulatory compliance notices 41 Modifications The FCC requires the user to be notified that any changes or modifications made to this device that a

Regulatory compliance notices 42 Disposal of waste equipment by users in private households in the European Union This symbol on the product or on

Regulatory compliance notices 43 Korean notice Class A equipment Class B equipment Battery replacement notice WARNING: Power products contain

Electrostatic discharge 44 Electrostatic discharge In this section Preventing electrostatic discharge...

Acronyms and abbreviations 45 Acronyms and abbreviations IEC International Electrotechnical Commission LED light-emitting diode NEC National Elect

Index 46 A alarm conditions 19 alarms, silencing 19 alarms, troubleshooting 28 authorized reseller 36 B backup time, insufficient 29 batter

Index 47 J Japanese notice 42 K Korean notices 43 L LED, power button 7 LEDs 6, 7 limited warranty 37 load protection guarantee 37 low-vo

Index 48 V Voltage Correction LED, location 7 Voltage Correction LED, troubleshooting 29 voltage specifications 32 voltage, configuring 14 W

Contents 5 Index...

Component identification 6 Component identification In this section UPS front panel...

Component identification 7 UPS front panel controls and LED indicators Item Description Function 1 Power On/Standby button Turns the UPS power

Component identification 8 Item Description Function 6 Battery Charge LED When the UPS is operating from utility power (the Power LED is green), t

Component identification 9 Item Description 6 Network Transient Protector OUT jack 7 Site Wiring Fault LED 8 Input power cord with NEMA 5-15 plug