HP Notebook Projection Companion Manual de usuario Pagina 1

HP Notebook Projection CompanionService Manual100% Recycled PaperVersion: ADate: 2009/12/14

51.3 System Block Diagram

62 Firmware Upgraded FlowThis chapter provides the information regarding relevant eq uipments and upgradingprocedure for firmware upgrade.Not

7USB Support - Installation (All Platforms)This release includes support for a USB communications interface to DDP2000-basedprojectors. The setup prog

8Operating procedure1. Connect the Projector and PC via USB cable.2. Double-click [DLP Composer (TM) Lite]. The following screen will appear.3. Select

912. Wait for the Completion of upgrading, and then remove AC Adapter, Power Cord andupgrading cable.2. Put checkmark next to[Skip Boot LoaderArea]，VA

103 Machine Disassembly and Replacement3.1 ToolsItemPhotoLong Nose NipperNipperScrew Bit(+):2*5*40Screw Bit(+):2*4*60Anti-static wrist strapAnti-stati

11StepFigureDescription11. Press the power button toshutdown the projector anddisconnect the AC Adapterand power cord.2Loosen the screwsJ1635-2684-00*

124Loosen the three screwsJ1635-3177-00*3 for movingBottom Cover.5Loosen the three screwsJ1635-2021-00*2 to removethe DC Fan J2394-0103-00.6Loosen J16

138Loosen screwsJ1635-2687-00*2 to removethe Focus-ring.9Loosen the four screwsJ1635-3177-00*4 to removethe DMD board.J1635-2687-00*2J1635-3177-00*4

143.3Mechanical Drawing2. Top Cover3. Back Cover4. Focus Ring6. Optical Engine5. DMD Board9. Main Board7. Fan8. OE Fan10. Bottom Cover11. Rear Foot1.

IIUpdate HistoryRevisionChapterChangesDateRev. AInitial version14th Dec.2009

154 Troubleshooting and Verifying the RepairThis chapter provides technicians and people who have an electronic backg round a primarydescription about

16Power Source TroubleshootingNGNGOKOKNGOKNGOKNGOKNGN o P o w e rSource afterturning onCheck ACsocket andconnectorCheck LEDand keypadFPCCheckMain boar

17Video Signal TroubleshootingNGOKNGOKNGComputerNo SignalCheckSourceCheckCableCheckOpticalEngineTurn onsourceReplaceCableReplaceOpticalEngineNGOKNGOKN

18NGOKNGOKNGImageabnormalPower onagain andreset OSDOKCheck inputcable andsignal settingCheckMain boardCheckOpticalengineAdjust InputSignalReplaceMain

19Operation Function Troubleshooting4.2Verifying the RepairAfter repairing projector (Dissembling and assembling projector), Repair center should veri

20(2) Operation testButtons operationButton descriptionTest criteriaPower1. Mechanical motion (Up & Down) should be free from getting stuckwhen pr

21Full darknessLight leak in active area and colorific light leak in inactivearea are not allowable.Twelve GridsPress “AUTO” button, more than three t

22256 level RGB--256 level of RGB color should be distinguishable, at leastRed color scales should be.-- For each RGB 256 levels, Noise or color devia

235 Color Temperature CalibrationWarning:. Operate LED Calibration in a dark room (don’t allow any light.)<0.5lux. Projected image size: 30 inches.

245. Input the Bar Code number of projector, then click [Calibration] to start Color TemperatureCalibration automatically.6. Thedialog boxas below ind

IIIDLP and DLP® logo are trademarks of TEXAS INSTRUMENTS INCORPORATED.© Copyright 2009 Hewlett -Packard Development Company, L.P.Microsoft, Windows, a

257. Click Pass[ ].8. Ensure the data of calibration is as same as the projector ’s. If not, please calibrate again.9. Turn off the projector normally

266 Connector InformationThis section provides each connector location on boards and function of each board. They will beuseful for your detecting the

277 Spare Parts listIntroduct ionThis section is a list of all the FRU removal. Following the FRU table of contents is an enlargedview of the entire p

28Appendix A: Computer CompatibilityAppendix B: Video CompatibilityNTSC-M, NTSC-4.43．PAL-M,N,B,D,G,H,I．SECAMSignalHorizontal Frequency (kHz)Vertical F

IVConventionsThe following conventions are used in this manual .Screen MessagesDenote actual messages that appear on screen.NoteGive bits and piece

VTable of Contents1 System Introduction ... ... ... ...

11 System Introduction1.1Technical SpecificationThe following tables list the specifications for the projector.MetricDimensionsHeight4.0 cmWidth11.1 c

21.2 Location of features, Controls, and I/OTop componentsComponentDescription(1) Focus ringMove the ring to the left or right to adjust the focu

3Front componentsComponentDescription(1) VentEnables airflow to cool internal components.(2) LensProjects images onto screen.Left components

4Right componentsComponentDescriptionVentsEnables airflow to cool internal components.Bottom componentsComponentDescription(1) VentsEnable airflo