HP P6350 Manual de usuario Pagina 170
- Pagina / 316
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Is the power on/standby button LED amber?
Possible SolutionsPossible ReasonsAnswer
No action required.System functioning properly.No
Yes
• Firmly press the power on/standby
button and hold for approximately
three seconds.
• The power on/standby button has
not been pressed firmly or held
long enough.
• • Be sure that all components are fully
seated.
The system midplane and/or
power button/LED assembly might
need to be replaced.
• Contact an authorized service
provider for assistance.
Is the power supply LED amber?
ActionsPossible ReasonsAnswers
No
• Remove and inspect the AC power
cords from both power supplies and
reconnect them.
• Both power cords not connected or
AC power is unavailable.
• Power supply functioning properly.
• No action required.
Yes
• Verify AC input power.• This supply is not receiving AC
power, but the other supply is
receiving AC power.
• Be sure that the power supply is
undamaged and is fully seated.
NOTE: It is possible for one
power supply to show a green
status and the other supply to show
an amber status.
• Be sure that all pins on connectors
and components are straight.
• Contact an authorized service
provider for assistance.
• Power supply might not be inserted
properly, might have a damaged
connector, or might have failed.
Is the I/O module fault LED amber?
Possible SolutionsPossible ReasonsAnswer
No action required.Functioning properly.No
Yes
• Make sure that the I/O module is
seated properly by pressing the I/O
• The I/O module is locked.
• The I/O module has failed.
module firmly into its bay after the
handle has clicked in place.
• Other fault condition exists.
CAUTION: Never remove an I/O
module from the chassis while the
status LED is green. Removing an
active I/O module can result in data
loss.
• Contact an authorized service
provider for assistance.
170 Troubleshooting
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- Contents 9 9
- 10 Contents 10
- Contents 11 11
- 12 Contents 12
- 1 P63x0/P65x0 EVA hardware 13
- Rear view 14
- Drive bay numbering 14
- Front view 14
- Disk drives 15
- Front status and UID module 16
- Power supply module 17
- Fan module 17
- I/O module 18
- Rear power and UID module 19
- Controller enclosure 21
- Controller status indicators 24
- Controller status LEDs 25
- Battery module 27
- Management module 28
- HSV controller cabling 29
- Storage system racks 30
- Power distribution units 31
- 1. Power receptacles 32
- 2. AC power connector 32
- 32 P63x0/P65x0 EVA hardware 32
- Moving and stabilizing a rack 33
- 34 P63x0/P65x0 EVA hardware 34
- 1. Hex nut 35
- 2. Leveler foot 35
- 2 P63x0/P65x0 EVA operation 36
- Implicit LUN transition 38
- Recovery CD 39
- Handling fiber optic cables 39
- Powering on disk enclosures 40
- Powering off disk enclosures 41
- Starting the storage system 41
- 42 P63x0/P65x0 EVA operation 42
- Using the management module 43
- 3. Reset button1. Status LEDs 44
- 2. Ethernet jack 44
- 44 P63x0/P65x0 EVA operation 44
- 46 P63x0/P65x0 EVA operation 46
- 48 P63x0/P65x0 EVA operation 48
- Overview 50
- Clustering 50
- Multipathing 50
- Adding hosts 51
- Scanning the bus 52
- HP-UX 53 53
- Accessing IBM AIX utilities 54
- Driver failover mode 55
- Installing a QLogic driver 55
- Upgrading Linux components 56
- Using the source RPM 57
- Console LUN ID and OS unit ID 59
- Adding OpenVMS hosts 59
- Oracle Solaris 63 63
- Fabric setup and zoning 65
- 50001fe1002709e9,5 68
- Oracle Solaris 69 69
- Configuring an ESX server 70
- VMware 71 71
- System prerequisites 73
- Installing the VAAI Plug-in 74
- VMware 75 75
- VMware 79 79
- Uninstalling the VAAI Plug-in 80
- VMware 81 81
- 4 Replacing array components 82
- Replaceable parts 83
- Replacement instructions 85
- 86 Replacing array components 86
- Figure 25 FCoE support 88
- Supported IP network adapters 93
- IP network requirements 93
- Set up the iSCSI Initiator 94
- Set up the iSCSI Initiator 95 95
- Set up the iSCSI Initiator 97 97
- Figure 37 Add Features page 101
- Figure 48 Select status 108
- Assigning device names 112
- Target bindings 113
- Mounting file systems 114
- Unmounting file systems 114
- MPxIO overview 118
- Edit the sgen.conf file 119
- Create an sgen driver alias 120
- # iscsiadm list target-param 121
- 1.01.50014380025da538 121
- Requirements 129
- Setting up authentication 131
- CHAP restrictions 131
- 6 Single path implementation 149
- Supported configurations 150
- HP-UX configuration 152
- HBA configuration 153
- Limitations 154
- Oracle Solaris configuration 155
- OpenVMS configuration 157
- Xen configuration 158
- Linux (32-bit) configuration 159
- Linux (Itanium) configuration 160
- IBM AIX configuration 162
- VMware configuration 163
- Mac OS configuration 164
- Failure scenarios 164
- Windows Servers 165
- Oracle Solaris 165
- 7 Troubleshooting 169
- Is the fan LED amber? 171
- Compromised fault tolerance 171
- 172 Troubleshooting 172
- Handling disk drive failures 173
- Figure 86 Beacon on command 174
- Issues and solutions 175
- 176 Troubleshooting 176
- 8 Error messages 180
- 9 Support and other resources 197
- Typographic conventions 198
- Customer self repair 198
- Rack stability 199
- FCC rating label 200
- European Union notice 201
- Japanese notices 202
- Korean notices 202
- Taiwanese notices 203
- Turkish recycling notice 203
- Laser compliance notices 204
- German laser notice 205
- Italian laser notice 205
- Japanese laser notice 205
- Recycling notices 206
- Hungarian recycling notice 208
- Italian recycling notice 208
- Latvian recycling notice 208
- Lithuanian recycling notice 208
- Polish recycling notice 208
- Portuguese recycling notice 209
- Romanian recycling notice 209
- Slovak recycling notice 209
- Spanish recycling notice 209
- Swedish recycling notice 209
- Battery replacement notices 210
- German battery notice 211
- Italian battery notice 211
- Japanese battery notice 212
- Spanish battery notice 212
- Internal component envelope 213
- EIA310-D standards 213
- Airflow and Recirculation 214
- Configuration Standards 214
- UPS Selection 214
- C Command reference 217
- Example: : 222
- Initiator 223
- Example 2: 224
- Example 3: 224
- Example 4: 224
- Example: 225
- Admin sessionAuthority 228
- 228 Command reference 228
- Set alias 232
- Set CHAP 233
- Set features 234
- Set iSCSI 235
- Set iSNS 236
- Set Mgmt 236
- Set properties 237
- Set SNMP 238
- Set system 239
- Set VPGroups 239
- Show CHAP 242
- Show features 244
- Show initiators 244
- Show initiators LUN mask 246
- Show iSCSI 247
- 248 Command reference 248
- Show iSNS 249
- Show logs 249
- Show LUNinfo 250
- Show LUNs 251
- Show lunmask 252
- Show memory 252
- Show mgmt 253
- Show NTP 253
- Show perf 254
- Show presented targets 255
- 256 Command reference 256
- Commands 257 257
- Show properties 258
- Show SNMP 259
- Show stats 259
- 260 Command reference 260
- Show system 261
- Show targets 262
- Show VPGroups 262
- Shutdown 263
- Traceroute 264
- D Using the iSCSI CLI 265
- 266 Using the iSCSI CLI 266
- SNMP parameters 269
- Management Information Base 270
- FC port table 272
- Initiator object table 273
- LUN table 275
- VP group table 277
- Sensor table 278
- Notifications 279
- System information objects 280
- Notification objects 280
- Agent startup notification 281
- Agent shutdown notification 281
- FC port down notification 281
- Sensor notification 283
- Generic notification 283
- Glossary 298
- 300 Glossary 300
- 302 Glossary 302
- 304 Glossary 304
- 306 Glossary 306
- 308 Glossary 308
- 310 Glossary 310
- 312 Index 312
- 314 Index 314
- 316 Index 316
Relacionado con productos y manuales para Software HP P6350
Software HP CD52ce Manual de usuario
(109 paginas)
(109 paginas)
Software HP STORAGEWORKS XP20000 Manual de usuario
(76 paginas)
(76 paginas)
Software HP -UX SNAplus2 Manual de usuario
(398 paginas)
(398 paginas)
Software HP D2D2502i Manual de usuario
(178 paginas)
(178 paginas)
Software HP Firewall Series Manual de usuario
(119 paginas)
(119 paginas)
Software HP tc4400 Guía de usuario
(86 paginas)
(86 paginas)
Software HP PROCURVE 2520 Manual de usuario
(544 paginas)
(544 paginas)
Software HP 1.x Papel blanco
(16 paginas)
(16 paginas)
Software HP B6960-90078 Manual de usuario
(856 paginas)
(856 paginas)
Software HP 2600-PWR Manual de usuario
(418 paginas)
(418 paginas)
Software HP 5992-3193 Manual de usuario
(66 paginas)
(66 paginas)
Software HP Laptop 7.2 Manual de usuario
(53 paginas)
(53 paginas)
Software HP 1.5TB Manual de usuario
(216 paginas)
(216 paginas)
Software HP 2/8q Manual de usuario
(188 paginas)
(188 paginas)
Software HP T5700 Manual de usuario
(76 paginas)
(76 paginas)
Software HP XP512 Manual de usuario
(99 paginas)
(99 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales