Hp XP P9000 Command View Advanced Edition Software Manual de usuario Pagina 238
- Pagina / 492
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6. Set the operation (Pair Operation) and options to change the pair status, and then click Next.
The Confirm page appears.
CAUTION:
Please confirm the following before confirming the pair status change operation:
• Before a split operation is performed, ensure that I/O processing for the primary volume
is not being performed because this operation might result in incomplete data in the
secondary volume.
• Before a Resync operation, ensure that the data in the secondary volume is no longer
required because this operation will overwrite the secondary volume data.
• Before a Restore operation is performed, ensure that the data in the primary volume is
no longer required because this operation will overwrite the primary volume data.
• Ensure the value of the copy pace is correct because this operation may take longer if
an incorrect value is used.
7. Check the specified settings, and then click Confirm.
The Finish page appears.
8. Click Finish.
The settings specified in the wizard are registered as tasks. Check the Status column for the tasks
to make sure that the pair status was changed successfully. To view the tasks, from the Explorer
menu, select Tasks and then Tasks.
TIP:
In 3DC Delta Resync configurations, executing pair operations against Cnt Ac-S or Cnt Ac-J (DeltaUR)
changes the related copy group status. Refresh configuration after the Task execution. If the related
copy group status is not changed, execute the Refresh Copy Group operation.
Related topics
• Change pair status workflow, page 233
• Limitations when performing 3DC configuration pair operations (mainframe systems), page 169
• When performing operations on EXCTGs (mainframe systems), page 211
Confirming copy status during task execution
To confirm copy status during task execution:
1. In the Explorer menu, choose Tasks and then Tasks.
A list of tasks is displayed in the Tasks subwindow.
2. Select a task and click the copy group name hot link.
The copy-group-name subwindow is displayed
3. Confirm the copy progress and whether the pair is in Copying status.
4. After several minutes, click Refresh Copy Group.
5. Confirm whether the pair is in Pair status.
Managing pair life cycle238
- User Guide 1
- DescriptionEditionVersionDate 2
- Contents 3
- User Guide 19 19
- Preface20 20
- 1 Introduction 21
- Replication Manager features 22
- Architecture and components 23
- System configurations 24
- User Guide 25 25
- Introduction26 26
- User Guide 27 27
- Introduction28 28
- HP P9000 Replication Manager 29
- Software Configuration Guide 29
- Introduction30 30
- 2 Getting started 31
- Initial setup 32
- Getting started34 34
- Logging in and out 36
- Quick start 37
- Getting started38 38
- 3 Replication Manager console 39
- Global tasks bar area 40
- Explorer menu 40
- Explorer menu items 41
- Dashboard menu 42
- Application bar area 42
- Navigation area 42
- Application area 42
- Object tree 42
- Functional views 43
- Structure of the Hosts view 44
- Storage Systems subwindow 45
- Pair configurations subwindow 47
- Information Source 48
- Replication Manager console48 48
- Applications subwindow 49
- Applications 50
- User Guide 51 51
- Replication Manager console52 52
- About information sources 53
- Configuration Guide 54
- Setting up Application Agent 57
- Automatic operation 61
- Manual operation 62
- Parallel performance 62
- About VDI generation timeout 64
- Refreshing Application Agent 65
- 5 Discovering volumes 67
- Volume scan 68
- Example volume scan procedure 69
- Types of volume scans 69
- Discovering volumes70 70
- Performing a volume scan 71
- Discovering volumes72 72
- Reviewing mainframe volumes 76
- Reviewing paired LDEV list 77
- Reviewing unpaired DEVN list 77
- Reviewing unpaired LDEV list 78
- 6 Setting up authorities 79
- About user roles 80
- About user roles and wizards 82
- Adding users 83
- Changing user permissions 84
- Setting up resource groups 85
- Creating resource groups 86
- Setting up authorities88 88
- Setting up authorities90 90
- 7 Organizing resources 91
- Setting up sites 92
- Adding sites 93
- Adding hosts to a site 94
- Organizing resources96 96
- Setting up My Copy Groups 97
- Examples of My Copy Groups 98
- Organizing resources100 100
- Creating My Copy Groups 101
- Organizing resources102 102
- 8 Setting up storage systems 103
- For mainframe systems 104
- HP P9000 104
- YYYStorage SystemsResources 105
- Setting up V-VOLs 106
- V-VOL limits 107
- About the Create V-VOL Wizard 108
- Creating V-VOLs 108
- Setting up command devices 110
- YYVolume not a paired volume 111
- YYVolume not a virtual volume 111
- Adding command devices 112
- Setting up remote paths 113
- Creating a remote path 114
- Setting up pool volumes 115
- About the Create Pool Wizard 117
- Setting up journal groups 118
- Create journal group workflow 121
- Adding journal groups 122
- Setting up storage systems124 124
- Setting up alerts 125
- Copy pair status 126
- Performance threshold 126
- Copy license usage threshold 126
- Alert completion 127
- Alert retention 127
- Alert limits 127
- Alert setting workflow 128
- Setting up refresh intervals 136
- About data retention periods 137
- Related topics 139
- User Guide 139 139
- 10 Managing pair life cycle 141
- Pair configuration workflow 144
- Method for 146
- About copy pairs 147
- Create copy pair workflow 148
- Managing pair life cycle154 154
- Managing pair life cycle156 156
- Editing pair names 157
- Defining copy groups 159
- Managing pair life cycle160 160
- About HORCM instances 161
- Creating copy groups 162
- Changing copy group names 163
- Managing pair life cycle164 164
- Managing pair life cycle166 166
- About delta resync 169
- Scheduling and managing tasks 170
- About task statuses 172
- Scheduling tasks 174
- Editing tasks 175
- Managing pair life cycle176 176
- Viewing a list of tasks 177
- Canceling tasks 177
- Deleting tasks 178
- Managing pair life cycle180 180
- Confirming distribution hosts 181
- About workflows 181
- Saving workflows 181
- Viewing a list of workflows 182
- Editing workflows 182
- Deleting workflows 183
- Managing pair life cycle184 184
- HP P9000 Command 185
- Managing pair life cycle186 186
- Managing pair life cycle190 190
- Editing copy group settings 191
- Managing pair life cycle192 192
- Editing a path group ID 194
- Deleting copy groups 194
- Managing pair life cycle196 196
- Performing pair operations 198
- About copy pair status 211
- Copy pair status categories 212
- About copy pair states 218
- Changing copy pair status 222
- Change pair status workflow 233
- Managing pair life cycle234 234
- Managing pair life cycle236 236
- Managing pair life cycle238 238
- Takeover operation 240
- Swap operation 241
- Force-split operation 241
- Advanced recovery use cases 242
- Workflow refer 243
- User Guide 243 243
- Figure 7 Takeback workflow 245
- User Guide 245 245
- Figure 6 Takeover workflow 245
- Managing pair life cycle246 246
- OptionCommandOptionOperation 248
- Basic operations 249
- Advanced operations 249
- About virtual command devices 251
- Management server 252
- Managing pair life cycle252 252
- HP P9000 Replication 253
- Manager Configuration Guide 253
- HP P9000 RAID 253
- Manager User Guide 253
- RAID Manager User Guide 254
- Managing pair life cycle256 256
- HORCM definitions 258
- User authentication 259
- Managing pair life cycle260 260
- Configuration information 261
- Copy pair status information 261
- Refreshing copy pair status 263
- 3 minutes0 to 1,000 264
- 5 minutes1,001 to 2,000 264
- 10 minutes2,001 to 3,000 264
- 15 minutes3,001 to 5,000 264
- User Guide 265 265
- Automatic refreshing 271
- Periodic refreshing 272
- Refresh status messages 272
- User Guide 273 273
- 12 System monitoring 277
- Monitoring copy license usage 278
- System monitoring280 280
- Monitoring pair status 282
- Displaying My Copy Groups 283
- DescriptionIcon 284
- Checking the copy pair status 286
- About copy pair status checks 286
- System monitoring288 288
- About performance monitoring 289
- About copy progress 290
- Viewing copy progress 291
- Pool usage threshold values 292
- Monitoring license usage 294
- About data protection status 295
- System monitoring296 296
- System monitoring298 298
- 13 Managing My Copy Groups 299
- Checking My Copy Groups 300
- Editing My Copy Groups 300
- 14 Managing resources 301
- Viewing a list of hosts 303
- Managing resources304 304
- (mainframe systems) 308
- Managing resources310 310
- LDEV display format 311
- Managing resources312 312
- Managing resources314 314
- 15 Managing storage systems 315
- Managing command devices 316
- Managing remote paths 317
- About deleting remote paths 318
- Managing pool volumes 319
- Editing pools 320
- Deleting pools 320
- Managing journal groups 321
- Managing storage systems322 322
- Managing storage systems324 324
- 16 Managing sites 325
- Site management functions 326
- Viewing a list of sites 327
- Editing sites 327
- Removing hosts from a site 328
- Deleting sites 329
- Deleting individual sites 330
- Deleting multiple sites 330
- 17 Managing alerts 331
- Viewing alerts and settings 332
- Testing alert settings 333
- Editing alert settings 334
- Marking alerts as completed 334
- Deleting alert settings 335
- Managing alerts336 336
- 18 Managing licenses 337
- Viewing license information 338
- Editing a license 338
- • About licenses, page 337 339
- User Guide 339 339
- Managing licenses340 340
- User management functions 341
- Managing users 342
- Changing user roles 344
- Deleting users 345
- Managing user permissions 346
- Managing user profiles 347
- Viewing user profiles 348
- About account locking 350
- Locking user accounts 350
- Unlocking user accounts 351
- About user authentication 352
- 20 Managing resource groups 357
- Editing resource groups 358
- Managing resource groups360 360
- Deleting resource groups 361
- Managing resource groups362 362
- 21 Managing security 363
- NYSecurityAdministration 364
- Managing security364 364
- About warning banners 366
- Editing a warning banner 367
- Deleting a warning banner 367
- Managing security368 368
- Editing information sources 369
- Removing information sources 371
- User Guide 375 375
- About application replicas 377
- Mount points 381
- Remote operations 384
- Daylight savings time 385
- GPT disks and VSS Backups 385
- Creating replicas (backups) 385
- Event type: Error 386
- Event source: PlugPlayManager 386
- Event ID: 12 386
- User Guide 387 387
- Restoring replicas (restores) 388
- Unsupported functions 394
- Allocating metafiles 395
- Using a cluster configuration 396
- Provisioning Manager 397
- Coding rules for scripts 414
- Script entries 415
- Multiple 418
- Environment variables 419
- Agent script example 419
- Batch command file example 420
- Saving a replica to tape 421
- Restoring a replica from tape 422
- Command line tools 423
- Backing up the databases 426
- Restoring the databases 426
- Restarting operations 426
- 24 Handling errors 431
- Explorer menu (event logging) 432
- Icons for messages 432
- About MIB definition files 434
- Exporting alert history 436
- Exporting event log data 437
- 26 System maintenance 441
- About operation modes 442
- Viewing the operation mode 442
- Changing the operation mode 442
- System maintenance444 444
- Using the GetCTDelta command 445
- Location 446
- Examples 447
- Using the task commands 448
- Common options 449
- Managing tasks with scripts 452
- Contacting HP 455
- Related information 455
- Conventions 456
- User Guide 457 457
- User Guide 461 461
- Icons462 462
- B Exceptions 463
- For open systems 464
- Exceptions466 466
- C Display formats 471
- Display format of copy type 472
- Display formats474 474
- Glossary 475
- Glossary476 476
- Glossary478 478
- Glossary480 480
- Glossary482 482
Relacionado con productos y manuales para Almacenamiento Hp XP P9000 Command View Advanced Edition Software
Almacenamiento Hp StoreOnce Backup Manual de usuario
(156 paginas)
(156 paginas)
Philips 017266693 manuals
Owner’s manuals and user’s guides for Outdoor lighting Philips 017266693.
We providing 1 pdf manuals Philips 017266693 for download free by document types: Datasheet
Comentarios a estos manuales