HP Compaq Elite 8300 Touch All-in-One Manual de usuario

Busca en linea o descarga Manual de usuario para Barebones Pc / Estación De Trabajo HP Compaq Elite 8300 Touch All-in-One. Installation Instructions Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 10
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
TouchMD Computer Setup (version December 2012) Page 1
TouchMD Computer Setup
TouchMD currently uses the 23” HP Compaq Elite 8300 or HP TouchSmart 9300 Elite all-in-one computers.
The computers can be mounted on the with a Chief F Series wall mount or set on a desk/countertop using
the factory installed stands.
Tools Needed
Electric Drill
1/2” drill bit (for steel stud install)
1/8” drill bit (wood stud install & Pilot Holes)
#2 phillips head screwdriver
#3 phillips head screwdriver
Flat head screwdriver
Stud Finder
Bubble Level
Tape measure
Razor Blade
Pencil
Installation
1. Identify an agreeable location for the Touch Screen computer with the site contact. TouchMD advises
the site contact to work with their doctors to determine the location/height of the install and mark it
with tape prior to your arrival. Keep in mind the following as you place the Touch Screen computer:
1.1. Is the location suitable for the install?
1.1.1. The Touch Computer should be located on a wall where the doctor can use TouchMD to
educate the patient, and/or the patient can use TouchMD themselves the during a normal
consultation (the computer can swivel and extend up to 16” as needed).
1.1.2. The Touch Computer height should be between the EYE LEVEL of the doctor and patient
during a normal consultation (the computer can tilt up or down as needed).
1.1.3. The Touch Computer should be mounted on the closest wall stud available and at the
height indicated by the site contact.
1.2. Is there power for the screen (within 3 ft)?
1.3. Is this a safe location for the computer screen?
2. Install the Chief FWD wall mount for wood studs, or the Chief FWDSK for steel studs according to the
directions included in the box. If not mounting on the wall unbox the computer, setup at the desired
desktop location, and skip to step 9 below. If the instructions are not included with the mount, you
can download copies of these instructions at our website:
2.1. Chief FWD (wood stud): www.touchmd.com/documents/FWD_WoodStud.pdf
2.2. Chief FWDSK (steel stud): www.touchmd.com/documents/FWDSK_MetalStud.pdf
Vista de pagina 0
1 2 3 4 5 6 7 8 9 10

Indice de contenidos

Pagina 1 - TouchMD Computer Setup

TouchMD Computer Setup (version December 2012) Page 1 TouchMD Computer Setup TouchMD currently uses the 23” HP Compaq Elite 8300 or HP TouchSmart 93

Pagina 2

TouchMD Computer Setup (version December 2012) 8. Using the screws removed in step #11, awall-mounting hardware to the VESA adapter plate in the 100x1

Pagina 3

TouchMD Computer Setup (version December 2012) Page 2 3. Make sure to adjust the wall mount arms with the included 3/16” hex key so arm move freely

Pagina 4

TouchMD Computer Setup (version December 2012) Page 3 7. Run cables to computer and conceal inside wall mount arms per the Chief FWD or FWDSK cable

Pagina 5 - Windows 7 Setup

TouchMD Computer Setup (version December 2012) Page 4 12. Attach Web Cam AND/OR Insert Eye-fi SDHC cards: 12.1. Un-box MicroSoft LifeCam Cinema AN

Pagina 6 - Installing LogMeIn

TouchMD Computer Setup (version December 2012) Page 5 Windows 7 Setup (This step is not needed if shipped from TouchMD, refer to your work order fr

Pagina 7

TouchMD Computer Setup (version December 2012) Page 6 10.2. Experience Improvement Program: Select the “No” option 10.3. Click or touch “Next” 11.

Pagina 8 - Appendix B

TouchMD Computer Setup (version December 2012) Stand Removal 1. Make sure the computer is completely shut down, and disconnect the power adaptor from

Pagina 9

TouchMD Computer Setup (version December 2012) Stand Removal Instructions for the HP TouchSmart 9300 Elite 1. Make sure the computer is completely shu

Pagina 10

TouchMD Computer Setup (version December 2012) 5. Using a Torx or Flathead screwdriver,four screws attaching the computer stand to the back of the c

Comentarios a estos manuales

Sin comentarios