HP Value Serial/USB Receipt Printer II Manual de usuario Pagina 12
- Pagina / 155
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 1: Diagnostics and Conguration12
Indicators
Theprintercommunicatesvariousconditionsbothvisually,withthegreenLEDoraudibly,withaseriesoftonesorbeeps.
The following table lists these indicators.
Indicator Sequence Condition
LED Continuous, ashing quickly Paper out
Cover open
Knife unable to home
LED Continuous, ashing slowly Paper is low
Printhead too hot
Voltages low/high
LED Continuous, Double LED ash Write to permanent memory in progress
Tone Two-tone beep Start-up diagnostics completed successfully
(low frequency, high frequency)
LED Two-Tone beep When entering ash download mode*
and Tone (high frequency, low frequency)
Continuous, quick blinking of LED
*Note: The printer enters ash download mode when a download command is sent to
the printer.
The printer is also able to communicate its status to the host application if the application has been programmed to receive
this information
For more information about See this section
Error conditions and correcting them “ Troubleshooting” in the User Guide
Communication of printer status to the host application “Command descriptions” in Chapter 3: Programming
Commands, Status sections.
- HP Value Serial/USB 1
- Receipt Printer II 1
- Contents 3
- Start-up Diagnostics 9
- Runtime diagnostics 10
- Remote diagnostics 10
- A798IIDiagnosticsForm 11
- Indicators 12
- Printer conguration 13
- Conguring the printer 14
- Diagnostics modes 16
- Printer emulations 17
- Overview of commands 20
- Comparison to A793 20
- Character appearance 22
- Print zones 22
- Emulation modes 23
- Commands listed by function 24
- Text characteristics 25
- Graphics 26
- Real time 27
- Bar codes 27
- Command conventions 30
- Command descriptions 30
- Perform partial knife cut 31
- Generate tone 31
- Initialize printer 32
- Select cut mode and cut paper 33
- Print test form 34
- Port Idle Timeout 34
- Print and paper feed 35
- Feed n dot rows 36
- Add n extra dot rows 36
- Print and feed paper 37
- Print and feed n lines 37
- Horizontal tab 38
- Set column 38
- Set vertical line spacing 40
- Set horizontal tab positions 40
- Set relative print position 41
- To move to the left: 41
- Select justication 42
- Set left margin 42
- Set printing area width 43
- Text characteristics commands 44
- Select pitch (column width) 45
- Select print mode 46
- 47
- Cancel user-dened character 49
- Select or cancel italic print 50
- Select character size 54
- Set smoothing 55
- Download font list 57
- Congure use of font set 57
- Congure line spacing 57
- Double-byte fonts 58
- Select font ID number 59
- Select font style number 59
- Select bit image mode 61
- Turn on/o TIFF compression 61
- Select the current logo 63
- Dene downloaded bit image 64
- Print downloaded bit image 65
- Print raster graphics 65
- Print Flash Logo 66
- Dene Flash Logos 66
- Logo print with knife cut 66
- Enable constant speed logos 67
- Batch mode 68
- Transmit paper sensor status 69
- Transmit printer ID 69
- Transmit status 74
- Real time commands 75
- Preferred implementation 76
- Alternate implementation 76
- Moving data through the buer 76
- Real time status transmission 77
- Real time request to printer 79
- Real time commands disabled 80
- Automatic Status Back 81
- Ifn=0,ASBisdisabled 82
- Unsolicited status mode 84
- Store symbol data for QR Code 88
- Print symbol data for QR code 89
- Transmit QR code print size 90
- Select bar code height 92
- Print bar code 92
- Print multiple barcodes 94
- 29 107 n d1... 00 95
- 29 107 m nL nH d1... dn 95
- Sample symbol description: 97
- Select bar code width 97
- Set DataMatrix Parameters 98
- Set DataMatrix module size 99
- Page mode 102
- Select page mode 103
- Select standard mode 104
- Set print area in page mode 105
- Execute macro 107
- User data storage 108
- Flash object area pack 109
- Flash object delete 109
- Return ash area size 110
- Flash download 111
- Switch to ash download mode 112
- Return main program ash CRC 112
- Download application 113
- Reset rmware 113
- Settings commands 114
- Set diagnostics mode 115
- Enable or disable knife 115
- Set max power 115
- Set printer emulation 116
- Set partial cut distance 116
- Set default font 116
- Set font size 117
- Set printer ID mode 119
- Set vertical white space 120
- Set printer tone 120
- Set shutdown mode timeout 120
- Appendix A: 121
- Appendix B: 126
- Resident Character Sets 126
Relacionado con productos y manuales para Impresión y escaneo HP Value Serial/USB Receipt Printer II
(110 paginas)
(166 paginas)
(16 paginas)
Impresión y escaneo HP AMP 130 Printer Manual de usuario
(128 paginas)
(128 paginas)
(193 paginas)
(62 paginas)
(209 paginas)
(146 paginas)
(144 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.095 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales