HP StorageWorks Enterprise File Services WAN Accelerator Guía de usuario Pagina 75
- Pagina / 124
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
HP STORAGEWORKS ENTERPRISE FILE SERVICES WAN ACCELERATOR 2.1.5 DEPLOYMENT GUIDE 69
7 - WCCP DEPLOYMENTS
The service group ID is 90 and the interface with packets coming from the LAN is
fastEthernet0/0.
IMPORTANT: HP recommends that you redirect packets coming into the LAN interface of the
router with the redirect in feature on the router instead of the redirect out feature on the WAN
interface of the router so that packets do not go through the routing code twice on the router.
Only use the redirect out feature if it is impossible to use the redirect in feature.
To configure the
WCCP router
• At the system prompt, enter the following set of commands:
Router> enable
Router# configure terminal
Router(config)# ip wccp version 2
Router(config)# ip wccp 90
Router(config)# interface fastEthernet 0/0
Router(config-if)# ip wccp 90 redirect in
Router(config-if)# end
Router#
TIP: Enter configuration commands, one per line. End with CRTL-Z.
The service group 90 must be defined and configured on the HP EFS WAN
Accelerator.
Configuring the
Client-Side HP
EFS WAN
Accelerator
You configure the client-side HP EFS WAN Accelerator to be an in-path device with
WCCP support and you add the service group (that you defined on the router) to it.
In this example, the client-side, in-path HP EFS WAN Accelerator IP address is
10.1.0.2, its WAN router is 10.1.0.1, and the server-side HP EFS WAN Accelerator
primary IP address is 10.2.0.2.
To configure the HP
EFS WAN Accelerator
1. Connect to the HP EFS WAN Accelerator CLI. For detailed information, see the
HP StorageWorks Enterprise File Services WAN Accelerator Command-Line
Interface Reference Manual.
2. At the system prompt, enter the following set of commands:
client-SH > enable
client-SH # configure terminal
client-SH (config) # in-path enable
client-SH (config) # in-path oop enable
client-SH (config) # interface in-path ip address 10.1.0.2 /16
client-SH (config) # ip in-path-gateway 10.1.0.1
client-SH (config) # write memory
client-SH (config) # restart
In this example, you configure the client-side HP EFS WAN Accelerator to optimize
ports 135, 139, 445, 21, and 80 and to pass through all other traffic.
To add in-path rules to
reach the out-of-path,
server-side, HP EFS
WAN Accelerator
• At the system prompt, enter the following set of commands:
client-SH > enable
client-SH # configure terminal
- HP StorageWorks 1
- Contents 3
- Introduction 7
- Organization of 8
- This Guide 8
- Document 9
- Conventions 9
- Antivirus Compatibility 10
- Additional Resources 11
- 6 INTRODUCTION 12
- Contacting HP 13
- HP Storage Web Site 13
- INTRODUCTION 14
- Designing an HP EFS WAN 15
- Accelerator Deployment 15
- How Does SDR 16
- Transaction 17
- Prediction 17
- Definition of Terms 19
- Bypass Mode 19
- Failover Mode 20
- In-Path Deployments 23
- Basic Steps 24
- (Client-Side) 24
- (Server-Side) 26
- 24 2 - IN-PATH DEPLOYMENTS 30
- Virtual In-Path Network 31
- Out-of-Path Network 35
- Configuring Connection 45
- Forwarding 45
- Neighbors in 46
- Connection 46
- Using the CLI 50
- Policy-Based Routing 51
- Introduction to PBR 52
- Overview of CDP 52
- Version 12.2(17d) SXB1 53
- Deployments With PBR 55
- PBR Using the 57
- Management 57
- Attached to an Inside Router 61
- PBR Between VLANs 61
- To configure the Cisco 64
- 59 65
- Autodiscovery, and CDP 66
- 61 67
- Troubleshooting 68
- WCCP Deployments 69
- Introduction to WCCP 70
- EPLOYMENTS 71
- 7 - WCCP DEPLOYMENTS 73
- A Basic WCCP Configuration 74
- Configuring the 75
- Client-Side HP 75
- EFS WAN 75
- Accelerator 75
- 74 7 - WCCP DEPLOYMENTS 80
- Dual WCCP Deployment 82
- 77 83
- To configure the 84
- WCCP (6209) router 84
- Additional WCCP Features 85
- TCP Port 86
- Redirection 86
- Specific Traffic 87
- Failover 87
- Support 87
- Introduction to PFS 89
- PFS Terms 90
- PFS Operating 91
- How Does PFS Work? 92
- When to Use 93
- When to use 94
- Global Mode 94
- Configuration 94
- Checklist for 94
- 100
- 8 - PROXY FILE SERVICE 101
- To view share status 102
- RADIUS and TACACS+ 103
- Authentication 103
- FreeRADIUS 104
- Configuring a TACACS+ Server 106
- Configuring 107
- TACACS+ 109
- 105 111
- 7. Click Save 111
- Serial Cluster and Cascade 113
- Deployments 113
- Figure 10-1. Serial Cluster 114
- A Basic Serial 115
- Cluster 115
- Deployment 115
- Cascade Deployment 117
- Fixed-Target 118
- Glossary 119
- 114 GLOSSARY 120
- 116 GLOSSARY 122
- INDEX 123
Relacionado con productos y manuales para Routers HP StorageWorks Enterprise File Services WAN Accelerator
Routers HP SuperStack Firewall Series Manual de usuario
(214 paginas)
(214 paginas)
Routers HP EX495 Manual de usuario
(331 paginas)
(331 paginas)
Routers HP F150 Manual de inicio rápido
(26 paginas)
(26 paginas)
Routers HP Deskjet 6980 Manual de usuario
(32 paginas)
(32 paginas)
Routers HP 10BASE-T Manual de instalación
(104 paginas)
(104 paginas)
Routers HP OfficeConnect Router Series Manual de usuario
(112 paginas)
(112 paginas)
Routers HP JL066AABA Ficha de datos
(12 paginas)
(12 paginas)
Routers HP JG409A#ABB Ficha de datos
(46 paginas)
(46 paginas)
Routers HP JF240A Ficha de datos
(23 paginas)
(23 paginas)
Routers HP JF231A Ficha de datos
(20 paginas)
(20 paginas)
Routers HP JD026A Ficha de datos
(9 paginas)
(9 paginas)
Routers HP JE459A Ficha de datos
(7 paginas)
(7 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.120 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales