Hp EML E-series Tape Libraries Manual de usuario descargar pdf (Pagina 28)

2 Using the library

This chapter describes operating procedures for the library.

Powering on the library

1. Close the center door of the library and turn the center-door knob one-quarter turn clockwise

to lock it.

Figure 24 Closing the center door

2. At the back of the library, press the library main power switch to the I (On) position.

Figure 25 Library main power switch control

1. Library main power switch

NOTE: The following step applies only when the library is powered on for the first time or

when a new interface controller is installed. This step is necessary to put the interface controller

into managed mode.

28 Using the library

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 111 112

User Guide 1
Contents 3
4 Contents 4
Contents 5 5
6 Contents 6
1 Library overview 7
Parts of the library 10
Base module 11
12 Library overview 12
Expansion modules 13
Tape drive expansion module 14
Card cage expansion module 14
Controller cards 15
Library robotics controller 16
Interface Manager card 16
Controller cards 17 17
Interface controller 18
Functional description 19
Load ports and magazines 20
Tape drives 21
Operator control panel 22
Numbering 22
Numbering 23 23
Command View TL 26
Library and Tape Tools 27
2 Using the library 28
Powering off the library 29
Center-door interlock 29
Performing an inventory 29
30 Using the library 30
5. Insertion arrow 31
Using the OCP 32
Home screen 33
OCP tabs and status bar 33
Timeouts 34
OCP functions 35
Table 3 OCP components 36
Figure 32 OCP Status screen 38
Configuration screen 39
Operations screen 40
Controls and indicators 42
LTO tape drives 45
Library main power switch 47
Power distribution unit 49
Maintaining tape cartridges 50
Diagnostic support tools 51
Troubleshooting 51
Startup problems 53
OCP problems 55
Robotics problems 55
Operating problems 57
Tape drive problems 57
Interface controller problems 61
Default setting 63
3. CompactFlash memory card 65
Interface Manager card 65 65
Interface Manager card 67 67
Required tools 69
LTO2 or LTO3 tape drive 72
LTO4 and later tape drives 73
Load port magazine 75
5 Moving the library 77
Repacking the library 78
2. Corner posts1. Ramps 79
4. Cap3. Corrugated sheets 79
6 Support and other resources 80
Typographic conventions 81
7 Documentation feedback 83
Acoustics 86
B Regulatory statements 87
European Union notice 88
Japanese notices 88
Korean notices 89
Taiwanese notices 89
Turkish recycling notice 90
Laser compliance notices 91
German laser notice 92
Italian laser notice 92
Japanese laser notice 92
Recycling notices 93
Bulgarian recycling notice 94
Czech recycling notice 94
Danish recycling notice 94
Dutch recycling notice 94
Estonian recycling notice 95
Finnish recycling notice 95
French recycling notice 95
German recycling notice 95
Latvian recycling notice 96
Greek recycling notice 96
Hungarian recycling notice 96
Italian recycling notice 96
Lithuanian recycling notice 97
Polish recycling notice 97
Portuguese recycling notice 97
Romanian recycling notice 97
Battery replacement notices 98
French battery notice 99
German battery notice 99
Italian battery notice 100
Japanese battery notice 100
Spanish battery notice 101
D Installing a redundant PDU 104
Glossary 106
108 Glossary 108
110 Index 110
112 Index 112

Comentarios a estos manuales

Sin comentarios

Hp EML E-series Tape Libraries Manual de usuario Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para Almacenamiento Hp EML E-series Tape Libraries