Hp EML E-series Tape Libraries Manual de usuario Pagina 40
- Pagina / 112
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 5 Configuration screen functions (continued)
DescriptionFunction
Both IPv4 and IPv6 can be enabled, but both cannot be disabled at
the same time.
• Configure Barcode Reporting Formats—Defines how barcodes appear
on the OCP and sent to the host. Barcode reporting can be configured
as 6 to 8 characters and left or right aligned. If 6 characters with left
alignment is chosen, any characters after the six are truncated. With
6 characters and right alignment, only the last six characters are shown
with the beginning characters truncated.
• Configure Reserve Slots Up to nine slots can be reserved for special
purposes, such as cleaning tapes. The default is none. Select the number
you want to reserve and select Save.
NOTE: Reserve slots are not available on the EML 71e.
• Configure Inventory Mode enables you to require barcodes on tape
cartridges, or to make them optional. Requiring barcodes significantly
shortens inventory time.
Use the up and down arrows to adjust the screen contrast. The screen
refreshes each time an arrow is pressed. Select the OK button when
finished.
Adjust Screen Contrast
Operations screen
The Operations screen provides access to screens that enable you to unlock load ports, unlock the
library door, reboot the library, move tapes, clean tape drives, and run administrative tests.
Figure 34 OCP Operations screen
Table 6 Operations screen functions
DescriptionFunction
Instructs the robot to unlock all load port doors. In library firmware version
1407 or later, this option can be protected using the admin password.
Unlock Load Ports
(Password protection is enabled or disabled from the Configuration
screen.) When all load port doors are closed, each load port is scanned
and inventoried.
Parks the robot, which enables you to open the center door of the library.
The library is reinventoried after the center door is closed.
Unlock Door
Does a library reboot. Does an inventory of all tape slots and rediscovers
all hardware controllers and tape drives.
Reboot Library
40 Using the library
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- 1 Library overview 7
- Parts of the library 10
- Base module 11
- 12 Library overview 12
- Expansion modules 13
- Tape drive expansion module 14
- Card cage expansion module 14
- Controller cards 15
- Library robotics controller 16
- Interface Manager card 16
- Controller cards 17 17
- Interface controller 18
- Functional description 19
- Load ports and magazines 20
- Tape drives 21
- Operator control panel 22
- Numbering 22
- Numbering 23 23
- Command View TL 26
- Library and Tape Tools 27
- 2 Using the library 28
- Powering off the library 29
- Center-door interlock 29
- Performing an inventory 29
- 30 Using the library 30
- 5. Insertion arrow 31
- Using the OCP 32
- Home screen 33
- OCP tabs and status bar 33
- Timeouts 34
- OCP functions 35
- Table 3 OCP components 36
- Figure 32 OCP Status screen 38
- Configuration screen 39
- Operations screen 40
- Controls and indicators 42
- LTO tape drives 45
- Library main power switch 47
- Power distribution unit 49
- Maintaining tape cartridges 50
- Diagnostic support tools 51
- Troubleshooting 51
- Startup problems 53
- OCP problems 55
- Robotics problems 55
- Operating problems 57
- Tape drive problems 57
- Interface controller problems 61
- Default setting 63
- 3. CompactFlash memory card 65
- Interface Manager card 65 65
- Interface Manager card 67 67
- Required tools 69
- LTO2 or LTO3 tape drive 72
- LTO4 and later tape drives 73
- Load port magazine 75
- 5 Moving the library 77
- Repacking the library 78
- 2. Corner posts1. Ramps 79
- 4. Cap3. Corrugated sheets 79
- 6 Support and other resources 80
- Typographic conventions 81
- 7 Documentation feedback 83
- Acoustics 86
- B Regulatory statements 87
- European Union notice 88
- Japanese notices 88
- Korean notices 89
- Taiwanese notices 89
- Turkish recycling notice 90
- Laser compliance notices 91
- German laser notice 92
- Italian laser notice 92
- Japanese laser notice 92
- Recycling notices 93
- Bulgarian recycling notice 94
- Czech recycling notice 94
- Danish recycling notice 94
- Dutch recycling notice 94
- Estonian recycling notice 95
- Finnish recycling notice 95
- French recycling notice 95
- German recycling notice 95
- Latvian recycling notice 96
- Greek recycling notice 96
- Hungarian recycling notice 96
- Italian recycling notice 96
- Lithuanian recycling notice 97
- Polish recycling notice 97
- Portuguese recycling notice 97
- Romanian recycling notice 97
- Battery replacement notices 98
- French battery notice 99
- German battery notice 99
- Italian battery notice 100
- Japanese battery notice 100
- Spanish battery notice 101
- D Installing a redundant PDU 104
- Glossary 106
- 108 Glossary 108
- 110 Index 110
- 112 Index 112
Relacionado con productos y manuales para Almacenamiento Hp EML E-series Tape Libraries
(72 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales