Hp EML E-series Tape Libraries Manual de usuario Pagina 60
- Pagina / 112
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 26 Common Interface Manager card issues (continued)
SolutionPossible causeSymptom
Check cabling and observe indicators on the Interface
Manager card, interface controllers, and tape drives.
Cabling
Configuration
• Check each interface controller for active link LEDs to each
tape drive.
• Check that the number of tape drives reported by the
library matches the number of tape drives reported by the
Interface Manager card. Check each interface controller
for correct number of tape drives mapped. Reboot
mismatched interface controllers or tape drives, if needed.
Restore default configuration on mismatched interface
controllers and reboot.
• Disconnect Interface Manager card from interface
controllers and restore system defaults on the Interface
Manager card. Reconnect connections to interface
controllers and reboot.
• Swap tape drive locations to see if the problem follows
the tape drive, and replace the tape drive, if needed.
Incompatible browser
version or Java
TM
support not enabled
Command View TL does not
run in the browser.
• Make sure that you are using a minimum of Microsoft
Internet Explorer 6.0 SP1 or later, or Netscape Navigator
6.2 or later.
• Make sure that Java support is enabled in the browser.
Download and install the Java 2 Platform, Standard Edition
1.4.2 or later from http://wwws.java.com.
Java Runtime
Environment (JRE) not
installed
Bad network connection
or network down
• Check all physical network connections. If the connections
are good, contact your network administrator.
• Ping the management station. If pinging fails and the IP
address is correct, contact your network administrator.
• Check the IP address of the management station. On the
management station, open a command shell and enter
IPCONFIG. You must use this IP address (or the network
name of the management station) in the URL to access
Command View TL.
Wrong IP address
Management station not
running, or Command
• Check to see if the management station is operational.
• Use the Services applet to make sure that the Command
View TL service is running on the management station.
View TL service not
running on management
station
Select Start→Settings→Control Panel→Administrative
Tools→Services.
Table 27 Interface Manager card LED fault isolation
ProceduresIndicators
Green LEDRed LED
Reset the Interface Manager card (see (page 43)). If the problem
persists, replace the Interface Manager card.
OffBlinks 1x per 5 second
interval
OffBlinks 2x per 5 second
interval
OffBlinks 3x per 5 second
interval
60 Troubleshooting and event reporting
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- 1 Library overview 7
- Parts of the library 10
- Base module 11
- 12 Library overview 12
- Expansion modules 13
- Tape drive expansion module 14
- Card cage expansion module 14
- Controller cards 15
- Library robotics controller 16
- Interface Manager card 16
- Controller cards 17 17
- Interface controller 18
- Functional description 19
- Load ports and magazines 20
- Tape drives 21
- Operator control panel 22
- Numbering 22
- Numbering 23 23
- Command View TL 26
- Library and Tape Tools 27
- 2 Using the library 28
- Powering off the library 29
- Center-door interlock 29
- Performing an inventory 29
- 30 Using the library 30
- 5. Insertion arrow 31
- Using the OCP 32
- Home screen 33
- OCP tabs and status bar 33
- Timeouts 34
- OCP functions 35
- Table 3 OCP components 36
- Figure 32 OCP Status screen 38
- Configuration screen 39
- Operations screen 40
- Controls and indicators 42
- LTO tape drives 45
- Library main power switch 47
- Power distribution unit 49
- Maintaining tape cartridges 50
- Diagnostic support tools 51
- Troubleshooting 51
- Startup problems 53
- OCP problems 55
- Robotics problems 55
- Operating problems 57
- Tape drive problems 57
- Interface controller problems 61
- Default setting 63
- 3. CompactFlash memory card 65
- Interface Manager card 65 65
- Interface Manager card 67 67
- Required tools 69
- LTO2 or LTO3 tape drive 72
- LTO4 and later tape drives 73
- Load port magazine 75
- 5 Moving the library 77
- Repacking the library 78
- 2. Corner posts1. Ramps 79
- 4. Cap3. Corrugated sheets 79
- 6 Support and other resources 80
- Typographic conventions 81
- 7 Documentation feedback 83
- Acoustics 86
- B Regulatory statements 87
- European Union notice 88
- Japanese notices 88
- Korean notices 89
- Taiwanese notices 89
- Turkish recycling notice 90
- Laser compliance notices 91
- German laser notice 92
- Italian laser notice 92
- Japanese laser notice 92
- Recycling notices 93
- Bulgarian recycling notice 94
- Czech recycling notice 94
- Danish recycling notice 94
- Dutch recycling notice 94
- Estonian recycling notice 95
- Finnish recycling notice 95
- French recycling notice 95
- German recycling notice 95
- Latvian recycling notice 96
- Greek recycling notice 96
- Hungarian recycling notice 96
- Italian recycling notice 96
- Lithuanian recycling notice 97
- Polish recycling notice 97
- Portuguese recycling notice 97
- Romanian recycling notice 97
- Battery replacement notices 98
- French battery notice 99
- German battery notice 99
- Italian battery notice 100
- Japanese battery notice 100
- Spanish battery notice 101
- D Installing a redundant PDU 104
- Glossary 106
- 108 Glossary 108
- 110 Index 110
- 112 Index 112
Relacionado con productos y manuales para Almacenamiento Hp EML E-series Tape Libraries
(72 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales