Hp StorageWorks 1510i Modular Smart Array Manual de usuario Pagina 83
- Pagina / 99
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
11 . View the messages displayed on the array controller LCD panel during startup to confirm that the
firmware was installed successfully and that the array controller restarts successfully.
NOTE:
In dual-controller configurations, firmware on the two controllers is compared each time
the MSA chassis is restarted. If the versions are mismatched, the system prompts to clone
the firmware on the controller with the latest version over to the controller with the earlier
version firmware. (For the system to operate in a dual-controller mode, firmware on the
controllers must match.)
The following message is displayed on the LCD panel of the controller with the earlier
firmware:
07 CLONE FIRMWARE ? ‘<‘ = NO, ‘>’ = YES
Press the > button on the LCD panel to clone the firmware. During the cloning process,
informational messages are displayed on the controller LCD panels. When the cloning
process is complete, the just-updated controller automatically restarts.
Updating hard drive firmware
SCSI hard drive firmware updates are performed using files on the ProLiant Firmware Maintenance CD
and are required only when the following message is displayed on the MSA controller LCD panel:
85 BAD DRIVE FRMWARE BOX <n> BAY <n>
CAUTION:
Before downloading new firmware,makenoteofthefollowing:
• Update system fi rmware during a scheduled maintenance window.
• Stop all host traffic to the array controller during the updating process.
• Make sure that a recent, known good back up of all data on the MSA array is available before
updating system firmware.
• Make sure that a copy of the configuration, including the iSCSI IP addressing and portal information,
along with the hard drive, LUN, and target information is available before updating system firmware.
• If it has been more than six months since you restarted your MSA storage system, HP recommends
that you power-cycle the MSA (power off, and then power on) before updating the firmware to
ensure that you are working with a fresh system.
• After the update is complete, power cycle the MSA and all of its attached hard drive storage
enclosures to activate the new firmware.
• For newly installed MSA, do not perform a firmware update until the controller batteries are fully
charged.
1. ObtaintheISOimageforthelatestProLiantFirmwareMaintenanceCDfromthefollowingwebsite:
h
ttp://www.hp.com/support/proliantstorage. Then, burn the image onto a CD using a standard
CD-ROM burning utility. Do not simply copy the ISO file to a blank CD.
NOTE:
If the latest Firmware Maintenance CD does not include the latest-release drive firmware
contained in a Smart Component, the CD can be used in combination with the latest
individual Smart Component package to perform the update.
2. Insert the CD into the CD-ROM drive of the server.
3. Using the navigation window, locate the inventory file on the CD and copy it to a temporary location
on the host. The filename may be similar to InventoryResultsLinux.xml.
HP Storage Management Utility user guide
83
- Part number: 383075–002 1
- Contents 3
- Document con 10
- About this guide 12
- 1Overview 13
- Page descripti 14
- Initial confi guration methods 14
- Accessing the SM 15
- Best prac 17
- 18 Ove rview 18
- Page description 19
- Available tasks 20
- For example, if 23
- 3Configure 25
- Configure 26
- Available task 27
- Sample configur 30
- Fundamental ta 33
- 4. Select Man 34
- Configuring data ports 35
- Configuring hard drives 38
- Creating array 39
- Creating logical drives 41
- Creating the target 43
- Creating target 45
- Assigning porta 46
- Mapping logical 47
- Adding authorized initiators 49
- Security tasks 51
- Setting the SSL certificate 56
- Adding a route (A 58
- Changing 58
- Deleting a component (Delete) 63
- Enabling iSNS discovery 65
- Enabling iSNS d 66
- Setting the pref 67
- 4Wizards 69
- 4. When prompted, click Next 70
- Password 73
- 5Diagnose 77
- Diagnose 78
- Prerequisites 79
- Updating MSA firmware 80
- Updating hard drive firmware 83
- A Storage overview 85
- Fault-tolerance levels 86
- RAID 0—no fau 87
- RAID 1+0—drive mirroring 87
- RAID 6—advanced data guarding 89
- Choosing a RAID level 90
- BIcondescriptions 91
- Icon descriptions 94
Relacionado con productos y manuales para Almacenamiento Hp StorageWorks 1510i Modular Smart Array
(64 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales