Hp ProLiant DL580 G4 Server Manual de usuario Pagina 73
- Pagina / 139
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Memory options 73
Observe the following warnings when performing a hot-plug replacement procedure.
WARNING: Always comply with all electrostatic and thermal guidelines to prevent bodily
injury and ensure a properly functioning system when performing hot-plug operations.
WARNING: To prevent personal injury from hazardous energy:
• Remove watches, rings, or other metal objects.
• Use tools with insulated handles.
• Do not place tools or metal parts on top of batteries.
Removing a memory board blank
To remove the memory board blank, squeeze the levers and pull the blank out of the server.
Removing and installing a memory board while the server is
running
Memory boards can be installed while the server is running in the following scenarios:
• Memory boards can be hot-added if the server is configured for Advanced ECC and hot-add is
enabled in RBSU.
• Memory boards can be hot-replaced if the server is configured for hot-plug mirrored memory or hot-
plug RAID memory.
IMPORTANT: Be sure to power down the server when performing board removal procedures
in a server that is not configured for Advanced ECC, hot-plug mirrored memory, or hot-plug
RAID memory.
1. Unlock the locking switch, and open the release latch.
CAUTION: Only memory boards with a green Removable LED can be removed. Do not
attempt to remove any memory board with the Removable LED off.
- User Guide 1
- Audience assumptions 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Front panel components 7
- Front panel LEDs and buttons 8
- • If the server is rebooted 9
- Processor module LEDs 11
- Rear panel components 12
- Rear panel LEDs and buttons 13
- Power supply LEDs 14
- System board components 15
- System maintenance switch 16
- Boot device selector switch 16
- Systems Insight Display LEDs 17
- DIMM slot locations 19
- SATA or SAS drive numbers 20
- SATA or SAS hard drive LEDs 20
- Fan locations 21
- Hot-plug fan LEDs 23
- Server operations 24
- • Diskette drive 25
- • Hard drives 25
- Removing the access panel 26
- Replacing hot-plug fans 27
- Removing the system cage 28
- Server operations 29 29
- Battery 30
- Remove the battery 31
- Server setup 32
- Rack planning resources 33
- Optimum environment 33
- Temperature requirements 34
- Power requirements 34
- Rack warnings and cautions 35
- Server setup 36 36
- Installing hardware options 37
- Registering the server 38
- Introduction 39
- Processor options 39
- Installing a processor 41
- 10. Install the PPM 44
- Battery-backed write cache 48
- Expansion board options 53
- 54
- Expansion board options 57 57
- Expansion board options 58 58
- Install the retaining clips 59
- Expansion board options 61 61
- Expansion board options 66 66
- Memory options 67
- Advanced ECC memory 68
- Online spare memory 69
- Hot-plug mirrored memory 70
- Hot-plug RAID memory 71
- Memory boards and DIMMs 72
- Memory options 73 73
- Memory options 74 74
- 3. Open the memory board 74
- Memory options 75 75
- 5. Close the memory board 75
- Memory options 77 77
- Configuring the memory 78
- POST memory test 79
- ROM-based diagnostics 79
- Selecting the AMP mode 79
- Memory options 80 80
- Server cabling 81
- BBWC cabling 82
- Server cabling 83 83
- Power switch cable assembly 84
- Server cabling 85 85
- Configuration tools 86
- HP ROM-Based Setup Utility 87
- Boot options 88
- BIOS Serial Console 88
- Array Configuration Utility 89
- Management tools 90
- HP Systems Insight Manager 91
- Management Agents 92
- Redundant ROM support 92
- USB support 92
- Diagnostic tools 93
- Keeping the system current 94
- ProLiant Support Packs 95
- Care Pack 95
- Electrostatic discharge 96
- Troubleshooting 97
- Symbols on equipment 98
- Warnings and cautions 98
- Symptom information 99
- Loose connections 100
- Service notifications 101
- Troubleshooting flowcharts 101
- General diagnosis flowchart 102
- Symptoms: 104
- Troubleshooting 106 106
- POST problems flowchart 107
- OS boot problems flowchart 108
- • Redundancy failure 111
- Troubleshooting 112 112
- Troubleshooting 113 113
- Troubleshooting 114 114
- Troubleshooting 115 115
- FCC rating label 116
- Class A equipment 117
- Class B equipment 117
- Modifications 118
- Japanese notice 119
- BSMI notice 119
- Korean notice 119
- Laser compliance 120
- Battery replacement notice 120
- Server specifications 122
- Specification Value 123
- Technical support 124
- Technical support 125 125
- Customer Self Repair 126
- Technical support 127 127
- Reparo feito pelo cliente 128
- Technical support 129 129
- Technical support 130 130
- Technical support 131 131
- Acronyms and abbreviations 132
- Index 136 136
- Index 137 137
- Index 138 138
- Index 139 139
Relacionado con productos y manuales para Hardware De La Computadora Hp ProLiant DL580 G4 Server
(154 paginas)
(187 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales