HP Omni 200-5000 Guía de usuario Pagina 15
- Pagina / 130
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
RM500SL
®
User's Guide Version 3.12
March 2015
Microphone care
Coupler microphone:
1. DO NOT twist the cable when attaching a coupler to the coupler microphone. Turn only the coupler or
unplug the coupler microphone before turning it.
2. DO NOT leave the coupler microphone plugged in when transporting.
3. DO make sure that the 2cc coupler is tightly screwed to the coupler microphone when performing hearing
instrument tests. Coupler leakage can cause feedback and erratic response curves.
4. DO make sure the tubing on the BTE (HA-2) coupler is free from any cracks/tears.
5. DO make sure that any replacement tubing used on the BTE coupler is either obtained from Audioscan, or is
#13 heavy wall earmold tubing exactly 10 mm in length.
Probe microphone:
Debris can alter the probe module reference microphone calibration and frequency response and can
permanently clog the probe module port.
1. DO NOT reuse probe tubes. Probe tubes can be wiped with alcohol wipes for re-use with the same patient,
but must not be used with multiple patients. Attempts at ultrasonic cleaning usually result in cerumen
becoming lodged in the lateral end which causes irreparable damage to the probe microphones.
2. DO NOT attempt to open or repair the probe microphone. Attempting to repair the probe module may lead
to damage or alteration of the factory calibration.
3. DO keep the probe module and probe tubes in a clean area.
4. DO stow the probe module when not in use or when transporting the RM500SL.
Battery pill use and care
Battery pills are optional. The thin connecting strip of each battery pill is fragile. When inserting pills into
hearing instrument battery compartments, take care that this strip is not pinched or bent severely as the battery
door is closed.
1. Select a battery pill that is appropriately sized for the hearing instrument that you are testing.
2. Insert the pill into the hearing instrument, carefully closing the battery door over the thin connecting strip.
3. Plug the pill’s cable into the battery pill jack inside the RM500SL Test box. (to the left of the coupler
microphone connection).
4. Turn the hearing instrument on.
15
- Audioscan RM500SL 1
- User's Guide 3.12 1
- Table of Contents 2
- 1 About RM500SL 6
- SAFETY WARNINGS and NOTICES 7
- Environmental safety 7
- March 2015 10
- Electronic User’s Guide 11
- 2 Getting Started 13
- General care instructions 14
- Microphone care 15
- Battery pill use and care 15
- 3 General Operation 18
- Keypad keys 19
- Menus, lists and buttons 20
- Screen messages and Help 21
- Software updating 21
- 4 General Setup 22
- 5 Networking 24
- NOAH Service Port 25
- Testing the NOAH service port 26
- 6 Single computer connection 27
- Local printer setup 30
- Printing to USB memory 31
- Network printer setup 32
- Printing to a network file 32
- Storing and restoring data 33
- Data storage using NOAH 35
- 8 Test Box Measures - Setup 36
- 1996 or 2003 ANSI standard 37
- ANSI test frequencies 37
- Test box calibration facts 37
- 9 ANSI Hearing Aid Tests 42
- ANSI test results 44
- ANSI input-output curves 44
- ANSI telecoil terminology 45
- Telecoil test results 46
- 10 Other Test Box Measures 48
- Multicurve procedure 49
- Multicurve results 49
- Battery drain test 50
- Manual control procedure 50
- 11 Sensory loss simulator 53
- 12 On-Ear Measures - Setup 54
- Max TM SPL setup 56
- ABR nHL to eHL setup 57
- Positioning the client 57
- Positioning the probe tube 58
- SPL or HL scale 60
- Hide or show on-ear curves 61
- On-ear feedback test 62
- On-ear noise reduction test 62
- On-ear manual control 63
- 15 Occlusion Effect Test 65
- 16 RECD measurement 66
- Measure RECD 67
- RECD results 68
- ANSI S3.46(2013) RECD 69
- RECD protocols 69
- RECD facts 70
- 17 Insertion Gain 72
- Insertion gain in HL 73
- Audiometric data entry 73
- REUR measurement procedure 74
- REAR measurement procedure 75
- 18 Speechmap 77
- DSL 5.0 changes 78
- NAL-NL1 in Speechmap 78
- NAL-NL2 in Speechmap 78
- Camfit in Speechmap 79
- Using Speechmap 79
- Speechmap Setup 80
- Screen tour - aided screen 82
- On-ear or Test box mode 82
- Assessment data entry 87
- Assessment data choices 88
- Open fittings in Speechmap 91
- FM fitting and verification 93
- Speechmap stimuli 95
- Stimulus levels 95
- Microphone location effects 96
- Deep insertion compensation 97
- Speech signal analysis 97
- 21 Troubleshooting 98
- Test box speaker overdriven 99
- Invalid on-ear calibration 101
- Barcode scanner malfunction 101
- 22 Technical 104
- Specifications 104
- Sensory Loss Simulator 105
- 23 Glossary 107
- 24 References 112
- 25 Appendix 1 115
- 26 Appendix 2 118
- 1 Introduction 119
- 2 The test signals 119
- 2.1 Narrow-band signals 120
- 2.2 Broad-band signals 120
- 2.2.3 Real-speech signals 122
Relacionado con productos y manuales para Barebones Pc / Estación De Trabajo HP Omni 200-5000
Barebones Pc / Estación De Trabajo HP Z600 - Workstation - 6 GB RAM Especificaciones rápidas
(80 paginas)
(80 paginas)
Barebones Pc / Estación De Trabajo HP SP750 - Professional - 256 MB RAM Especificaciones
(200 paginas)
(200 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales