Hp 3PAR Remote Copy Software Manual de usuario Pagina 74
- Pagina / 344
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3.12
Setting the Remote Copy Transport Layer
Remote Copy User’s Guide InForm OS Version 2.3.1
If the MTU value of 9000 is supported by the network, increase the MTU as follows:
1 For the GigE ports on each storage server, increase the MTU size to 9000 as follows:
:
where <N:S:P> represents the location of a GigE port, expressed as node:slot:port.
2 After setting the MTU to 9000 bytes for all GigE ports, verify that the network supports the
increased MTU size from any storage server as follows:
This command performs a ping from the specified interface (
<N:S:P>) to the specified IP
address on the target system (<IP_address>) while specifying a packet size of 8972 and
preventing fragmentation of packets. Issue this command twice (once for each interface),
for each system in the configuration.
◆ If the pings succeed, the network supports the new setting. Proceed to Setting Up
Remote Copy on page 3.16.
NOTE: Depending on workload, you might see as much as a 50 percent increase in
throughput by using a 9000 byte MTU setting as opposed to a 1500 byte MTU
setting.
# controlport rcip mtu 9000 <N:S:P>
Remote Copy change successful.
NOTE: Remember to change the MTU setting for both ports in each storage
server to be used in the Remote Copy configuration.
# controlport rcip ping -s 8972 -pf <IP_address> <N:S:P>
NOTE: Because of the spanning tree and MAC address learning, you might need
to ping each server several times before all tables are updated and the ping
succeeds.
- 3PAR Remote Copy 1
- User’s Guide 1
- 3 Remote Copy Setup 5
- 4 Using Remote Copy 6
- AQuick Setup Guide 7
- B Remote Copy Commands 7
- D Comparing MTU Speeds 9
- RH Revision History 9
- Table of Contents 10
- Introduction 11
- 1.1 Audience 12
- 1.2 Related Documentation 12
- 1.3 Organization 13
- 1.4 Typographical Conventions 14
- 1.5 Advisories 15
- Advisories 16
- Remote Copy Overview 17
- 2.1 Overview 19
- 2.2.2 Remote Copy Concepts 20
- 2.4 Remote Copy Pairs 22
- 2.5 Remote Copy Configuration 23
- Remote Copy Configuration 24
- 2.5.3 N-to-1 Configurations 25
- 2.5.4 1-to-N Configurations 27
- 2.6 Remote Copy Targets 31
- Direction of data 32
- 2.7 Remote Copy Links 33
- 2.8 Remote Copy Connections 34
- 2.8.1 IP Networks 35
- 2.9 Remote Copy Operation 36
- 2.9.1 Volume Group Modes 38
- 2.9.1.1 Synchronous Mode 39
- 2.9.1.1.1 Latency 40
- 2.9.2 Synchronization Types 41
- Remote Copy Operation 42
- 2.9.7 Role Reversal 46
- 2.11.1 In Synchronous Mode 47
- Use of Virtual Copy Snapshots 48
- 2.13 Error Handling 51
- 2.13.2 Double Link Failure 52
- Error Handling 53
- 2.13.5 Write Errors 54
- 2.13.6 Read Errors 55
- TCP/IP Network 57
- Requirements and Restrictions 58
- N-to-1 Restrictions 59
- 2.14.2 1-to-N Restrictions 60
- Remote Copy Setup 63
- 3.1 Available Setup Methods 64
- 3.2 Preparing for Setup 64
- 3.4.2.1 Setting the Gateway 71
- <N:S:P>) 72
- 3.5 Setting Up Remote Copy 78
- 3.5.1.4 Start Copying 85
- Node 0 WWN: 20210002AC0000C3 92
- Node 1 WWN: 21210002AC0000C3 92
- <group_name> 100
- Using Remote Copy 107
- 4.1 Management 108
- 4.5 Manual Resynchronization 111
- Modifying Virtual Volumes 115
- 4.9 Limiting Throughput 116
- 4.10 Stopping Remote Copy 117
- 4.11 Remote Copy Commands 117
- Remote Copy Commands 118
- Remote Copy volume group 120
- Task Command 120
- Performance and Scripting 121
- Considerations 121
- 5.1.2 Initial Synchronization 122
- 5.1.3 Distance 122
- 5.1.4 MTU Size 122
- 5.1.5 Autonegotiation 123
- 5.1.6 Remote Copy Mode 123
- 5.1.6.2 Synchronous Mode 124
- 5.3 Scripting Notes 125
- Scripting Notes 126
- Quick Setup Guide 127
- Table A-1. RCIP Setup 128
- A.3 Setting Up Remote Copy 129
- Table A-3. Remote Copy Setup 130
- Setting Up Remote Copy 131
- InForm OS CLI 135
- Administrator’s 135
- RESTRICTIONS 142
- EXAMPLES 142
- Group1 142
- specifier 173
- ■ Port. The port ID 208
- Group1 should be 218
- Example Setup and 219
- Disaster Recovery 219
- Chapter 3, Remote Copy Setup 220
- Remote Copy Setup Examples 221
- On InServ1: 224
- # showrcopy 224
- On InServ2: 225
- On InServ2 229
- InServ2 (Primary) 233
- InServ3 (Primary) 233
- InServ1 (Secondary) 233
- Direction of data replication 233
- InServ2 (Backup) 245
- InServ3 (Backup) 245
- InServ1 (Primary) 245
- ■ On InServA: 258
- ■ On InServB: 259
- ■ On InServC: 260
- InServB 267
- In the example above: 267
- ◆ On InServA: 269
- ◆ On InServB: 270
- ◆ On InServC: 271
- command on InServB and 281
- Primary-Rev) 284
- InServC 287
- -discard option bypasses 299
- To begin data migration: 317
- startrcopygroup -t 321
- Primary-Rev 326
- Primary, rather 329
- Comparing MTU Speeds 331
- Revision History 343
Relacionado con productos y manuales para Almacenamiento Hp 3PAR Remote Copy Software
(258 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales