Hp MPX200 Multifunction Router Manual de usuario Pagina 222
- Pagina / 258
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 34 MPX200 log messages (continued)
Response queue invalid handle for ET
pass-through.
FataliSCSI#%d: QLProcessResponseQueue:
Invalid handle for
ET_PASSTHROUGH_STATUS
70499
Response queue invalid entry type.FataliSCSI#%d: QLProcessResponseQueue:
Invalid entry type in response
queue %x
70501
Response queue invalid handle for
specified entry type.
FataliSCSI#%d: QLProcessResponseQueue:
Invalid handle %x EntryType %x
70502
Asynchronous event for unknown event
type.
FataliSCSI#%d: QLProcessAen: Invalid
event %x
70524
Reboot timer failed.FataliSCSI#%d: QLRebootTimer: Reboot
failed!
70544
iSCSI driver missed iSCSI processor
heartbeat. iSCSI processor rebooted.
FataliSCSI#%d: QLRebootTimer: Reboot
failed!
70563
iSCSI processor failed to complete
operation before timeout.
FataliSCSI#%d: QLRebootTimer: Reboot
failed!
70564
iSCSI processor system error restart.FataliSCSI#%d: QLRebootTimer: Reboot
failed!
70609
iSCSI processor reboot failed.FataliSCSI#%d: QLProcessSystemError:
RebootHba failed
70610
iSCSI processor NVRAM invalid
(checksum error).
FataliSCSI#%d: QLConfigChip: invalid
NVRAM
70784
iSCSI controller Set Flash command
failed.
FataliSCSI#%d: QLStartFw:
MBOX_CMD_SET_FLASH failed %x
70835
iSCSI controller failed to load
firmware.
FataliSCSI#%d: QLStartFw: Invalid Fw
loader state 0x%x
70836
iSCSI controller firmware load
operation timed out.
FataliSCSI#%d: QLStartFw: Load Fw loader
timeout
70837
iSCSI controller failed to initialize.FataliSCSI#%d: ql_adapter_up: Failed to
initialize adapter
70938
iSCSI controller reported that an SNS
response had an invalid handle.
FataliSCSI#%d: QLProcSrblessiSNSResponse:
Invalid handle %x
72351
iSCSI processor failed firmware
initialization.
ErroriSCSI#%d: QLUtmIoctlEnable:
Initialize FW failed
73990
iSCSI processor failed the internal
loopback test.
ErroriSCSI#%d: QLRunDiag: MBOX Diag test
internal loopback failed %x %x
74056
iSCSI processor failed the external
loopback test.
ErroriSCSI#%d: QLRunDiag: MBOX Diag test
external loopback failed %x %x
74057
iSCSI processor reported an invalid
ATIO Continuation type x.
ErroriSCSI#%d: QLUtmReceiveScsiCmd:
Invalid ATIO Continuation type
%x
74068
iSCSI processor reported an
Immediate data address
ErroriSCSI#%d: QLUtmProcessResponseQueue:
Immediate data addr %08x:%08x
in unsupported PduType
74069
(xxxxxxxx:xxxxxxxx) in an
unsupported PDU type.
iSCSI processor could not connect with
the iSNS.
ErroriSCSI#%d: QLiSNSEnableCallback: iSNS
Server TCP Connect failed
74241
222 Log messages
- Abstract 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- Contents 9 9
- MPX200 features 10
- MPX200 storage system support 10
- Management software 12
- Installation recommendations 20
- Total number of initiators 21
- Use of iSNS 21
- Use of iSCSI ports 21
- Balancing the load 21
- 10-GbE initiators 22
- Prerequisites 22
- General IP-SAN 23
- Network latency 25
- 3 Installing the MPX200 26
- Rack mounting the MPX200 27
- 1. Power cord 29
- Rack mounting the MPX200 29 29
- 4. Bezel3. Bracket arrows 30
- 30 Installing the MPX200 30
- Fibre Channel zoning 31
- Setting up the iSCSI IP ports 34
- Code load 36
- Locating the MPX200 38
- Removing an iSCSI controller 39
- Setting up the iSCSI ports 41
- LUN provisioning 42
- LUN provisioning 43 43
- Alternate procedure 45
- LUN management 48
- LUN management 49 49
- Figure 48 Expanded ports 50
- LUN management 51 51
- Supported IP network adapters 58
- IP network requirements 58
- Figure 56 Host details 63
- Multipathing 65
- Assigning device names 78
- Target bindings 78
- Mounting file systems 79
- Unmounting file systems 79
- MPxIO overview 83
- Editing the sgen.conf file 85
- Creating an sgen driver alias 86
- #mpathadm list lu 88
- Setting up authentication 97
- Setting up authentication 103 103
- Setting up authentication 107 107
- 8 MPX200 FCIP 108
- FCIP and iSCSI performance 110
- 112 MPX200 FCIP 112
- 114 MPX200 FCIP 114
- 116 MPX200 FCIP 116
- 118 MPX200 FCIP 118
- IP performance tuning 121
- Distance 122
- Bandwidth per route 122
- MTU/Jumbo frames 122
- Compression 123
- FCIP link diagnostics 126
- Configuring an FCIP route 127
- Step 3. Rack-mount the MPX200 128
- Step 4. Install the SFPs 128
- Install FCIP license 129
- Configuring an FCIP route 131 131
- 132 MPX200 FCIP 132
- FCoE configurations 133
- Ethernet 134
- Figure 114 Host type 137
- Figure 115 Host properties 137
- MPX200 chassis diagnostics 141
- Fibre Channel Port LEDs 142
- POST diagnostics 142
- Locating the MPX200 blade 144
- MPX200 log data 144
- MPX200 statistics 144
- MPX200 ping command 144
- WANLink diagnostic 145
- Issues and solutions 147
- Intended audience 151
- Related documentation 151
- Contacting HP 151
- Related information 152
- Typographical conventions 152
- Rack stability 153
- Product warranties 153
- 12 Documentation feedback 154
- A Command reference 155
- Fciproute 158
- Example 2: 159
- NoneAuthority 161
- Commands 161 161
- Initiator 163
- Commands 165 165
- Set alias 169
- Set CHAP 169
- Set chassis 170
- Commands 171 171
- Set features 172
- Set iSCSI 172
- Set iSNS 172
- Set Mgmt 173
- Set properties 174
- Set SNMP 174
- Set system 175
- Set VPGroups 175
- Show CHAP 178
- Show chassis 178
- Show fciproutes 179
- Show features 180
- Show initiators 180
- Show initiators LUNmask 180
- Show iSCSI 181
- Show iSNS 181
- Show logs 182
- Show LUNinfo 182
- Show LUNs 183
- Show LUNmask 183
- Show memory 184
- Show mgmt 184
- Show NTP 184
- Show perf 185
- Show presented targets 186
- Show properties 187
- Show SNMP 187
- Show stats 187
- 188 Command reference 188
- Commands 189 189
- Show system 190
- Show targets 190
- Show VPGroups 191
- Shutdown 191
- Traceroute 192
- Wanlinktest 192
- 194 Command reference 194
- Logging on to an MPX200 195
- Modifying a configuration 196
- SNMP parameters 199
- Management Information Base 200
- FC port table 202
- Initiator object table 204
- LUN table 205
- VP group table 207
- Sensor table 209
- Notifications 210
- Notification objects 211
- Agent startup notification 212
- Agent shutdown notification 212
- FC port down notification 212
- Target device discovery 212
- Notifications 213 213
- Notifications 215 215
- D Log messages 216
- Table 35 DM log messages 232
- Table 36 WD log messages 235
- Regulatory compliance notices 240
- BSMI notice 241
- Safety notices 242
- Power cords 243
- Japanese power cord statement 244
- Chinese warning messages 244
- English notice 244
- Dutch notice 244
- Czechoslovakian notice 245
- Estonian notice 245
- Finnish notice 245
- French notice 245
- German notice 245
- Greek notice 246
- Hungarian notice 246
- Italian notice 246
- Latvian notice 247
- Lithuanian notice 247
- Polish notice 247
- Portuguese notice 247
- Slovakian notice 248
- Slovenian notice 248
- Spanish notice 248
- Swedish notice 248
- Username: guest 250
- Password: password 250
- MPX200> admin start 250
- Glossary 251
- 252 Glossary 252
- 254 Glossary 254
- 256 Index 256
- 258 Index 258
Relacionado con productos y manuales para Almacenamiento Hp MPX200 Multifunction Router
Almacenamiento Hp X500 Data Vault Manual de usuario
(331 paginas)
(331 paginas)
Almacenamiento Hp OpenView Storage Management Appliance and Software Manual de usuario
(146 paginas)
(146 paginas)
Almacenamiento Hp XP7 Storage Manual de usuario
(208 paginas)
(208 paginas)
Almacenamiento Hp XP P9500 Storage Manual de usuario
(116 paginas)
(116 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales