HP Firewall Series Manual de instalación

HP A-F1000-A-EI/A-F1000-S-EI VPN Firewall Installation Guide Part number: 5998-1415 Document version: 6PW100-20110909

6 • Make sure there is enough space (greater than 10 cm (3.94 in)) around the air intake and outlet vents on the firewall for good ventilation. • M

7 CAUTION: • Check the resistance of the ESD-preventive wrist strap for safety. The resistance reading should be in therange of 1 to 10 megohm (Moh

8 RJ45 crimping pliers Multimeter Network cable tester Mark pen ESD-preventive wrist strap NOTE: No installation tool or ESD-preventive wrist

9 Item Requirements Result EMI prevention • Take effective measures to protect the power system from the power grid system. • Separate the protec

10 Installing the firewall This chapter includes these sections: • Installation flow • Installing the firewall in a 19-inch rack • Grounding the f

11 Figure 6 Install cage nuts Step2 Install the mounting brackets to both sides of the front panel, as shown in Figure 7. Figure 7 Install the mou

12 Figure 8 Fix the firewall to the rack Grounding the firewall WARNING! Correctly connecting the firewall grounding cable is crucial to lightnin

13 Figure 9 Connect the grounding cable 1 (1) OT terminal Installing an interface module CAUTION: A NSQ1XS2U0 interface module can be installed on

14 Connecting Ethernet cables Connecting a copper Ethernet cable Follow these steps to connect a copper Ethernet cable: Step1 Plug one end of an Eth

15 Step2 Plug the transceiver module into the SFP port of the firewall, as shown in Figure 12. Figure 12 Install the transceiver module To unplug

Legal and notice information © Copyright 2011 Hewlett-Packard Development Company, L.P. No part of this documentation may be reproduced or transmitte

16 Installing the power supply and connecting the power cord NOTE: • No AC power supply or DC power supply is provided with the firewall. • You

17 Figure 15 Connect an AC power cord Connecting the DC power cable Follow these steps to connect the DC power cable: Step1 Insert the DC power ca

18 Logging in to the firewall and configuring basic settings This chapter includes these sections: • Logging in to the firewall through the console

19 CAUTION: • When you connect a PC to a powered-on firewall, connect the DB-9 connector of the console cable tothe PC before connecting the RJ-45

20 Figure 19 Set the serial port used by the HyperTerminal connection Step3 Click OK after selecting a serial port and the following dialog box ap

21 Figure 21 HyperTerminal window Step5 Click Properties in the HyperTerminal window to enter the aaa Properties dialog box. Click the Settings ta

22 Logging in to the firewall through Telnet NOTE: For more information about the Telnet login, see the configuration guides for the firewalls. Y

23 Launch the web browser on the PC. Type 192.168.0.1 in the address bar and press Enter. The login dialog box appears, as shown in Figure 22. In thi

24 Figure 23 Basic configuration wizard: 1/6 Configuring the system name and user password Click Next on the first page of the basic configuration

25 Table 8 Basic information configuration items Item Description Sysname Set the system name. By default, the system name of the firewall is HP. Mo

i Contents Product overview···························································································································

26 Item Description HTTP Specify whether to enable HTTP on the device, and set the HTTP port number. Enabled by default. IMPORTANT: • If the curren

27 Figure 26 Basic configuration wizard: 4/6 (interface IP configuration) Table 10 Interface IP address configuration items Item Description IP Con

28 Figure 27 Basic configuration wizard: 5/6 (NAT configuration) Table 11 NAT configuration items Item Description Interface Select an interface on

29 Item Description Internal IP: Port If the internal server is enabled, set the IP address and service port number for the server on the internal LA

30 Hardware management and maintenance This chapter includes these sections: • Displaying detailed information about the firewall • Displaying soft

31 Status :Absent The SubCard2 on Board0: Status :Absent Displaying software and hardware version information of the firewall Use the d

32 MANUFACTURING_DATE :2010-06-29 VENDOR_NAME :HP Displaying the CPU usage of the firewall Use the display cpu-usage command to display the

33 Table 13 Output description Field Description Power 1 Number of the power supply Status The power supply state: • Normal—The power supply is

34 • Display the operational statistics of each functional module of the firewall. The output is too much and omitted here. <Sysname> display

35 • Use the reboot command to reboot a firewall. • Enable the scheduled reboot function at the CLI. You can set a time at which the firewall can a

ii Configuring NAT····································································································································

36 Troubleshooting This chapter includes these sections: • Power supply system failure • Fan failure • Configuration terminal problems • Password

37 Configuration terminal problems If the configuration environment setup is correct, the configuration terminal displays boot information when the f

38 When you set the password by using the set authentication password { cipher | simple } password command, follow these guidelines. • If the cipher

39 Cooling system failure When the temperature inside the firewall exceeds 45°C (113°F), the cooling system may have failed. Follow these steps to tr

40 Appendix A Technical specifications Dimensions and weight Table 14 Dimensions and weight Specification Item A-F1000-A-EI/A-F1000-S-EI Dimensions

41 Power input Table 17 Power input specifications Remarks Item A-F1000-A-EI/A-F1000-S-EI Rated voltage range 100 to 240 VAC; 50/60 Hz Maximum input

42 1. Technical specifications for copper Ethernet ports Table 19 Technical specifications for copper Ethernet ports Item Specification Connector RJ

43 Appendix B LEDs Front panel LEDs Figure 29 Front panel LEDs Table 21 Description of front panel LEDs LED Status Meaning OFF No link is present.

44 LED Status Meaning OFF Power supply 2 is not in position or power input is not available. PWR2 Green ON Power supply 2 is operational.

45 Appendix C Interface module NSQ1XS2U0 Introduction An NSQ1XS2U0 is a Layer 3 10-Gigabit Ethernet interface module, and provides two SFP+ optical

1 Product overview This chapter includes these sections: • Front panel view • Rear panel view NOTE: The A-F1000-S-EI and A-F1000-A-EI share the sa

46 Specification (dBm) Model Central wavelength Fiber mode Fiber diameter (μm) Bandwidth (MHz*km) Max transmission distance Optical transmit power Re

47 Appendix D AC power cables used in different countries or regions 10A AC power cables used in different countries or regions Table 24 10A AC powe

48 F type 04041056 (3 m, i.e., 9.8 ft) Holland, Denmark, Sweden, Finland, Norway, Germany, France, Austria, Belgium, and Italy Indonesia, Turkey, Rus

49 Connector outline Power cable outline Connector outline 7 Connector type Code (Length) Countries or regions where the type of power cables co

50 16A AC power cables used in different countries or regions Table 25 16A AC power cables used in different countries or regions Connector type Code

51 F type 0404A061 (3 m, i.e., 9.8 ft) Holland, Denmark, Sweden, Finland, Norway, Germany, France, Austria, Belgium, and Italy Indonesia, Turkey, Rus

52 I type 0404A01A (3 m, i.e., 9.8 ft) Australia Connector outline Power cable outline Connector outline

53 Support and other resources Contacting HP For worldwide technical support information, see the HP support website: http://www.hp.com/support Befor

54 Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text r

55 Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as

2 Table 1 Description of the “OPEN BOOK” mark Operation Reference Grounding the firewall Grounding the firewall Connecting the firewall to the power

56 Index A C D E F G I L N P R S A Accessories supplied by the firewall,8 C Checklist before installation,8 Combo interfaces,41 Configuration termi

3 Preparing for installation This chapter includes these sections: • Safety recommendations • Examining the installation site • Installation tools

4 • If there are two power inputs, disconnect the two power inputs to power off the firewall. • Do not work alone when the firewall has power. • A

5 Altitude Table 4 Altitude requirements Item Altitude Operating altitude –60 m (–196.85 ft) to 3 km (1.86 miles) Storage altitude –60 m (–196.85 f