Hp ProLiant DL380e Gen8 Server Manual de usuario Pagina 49
- Pagina / 142
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Hardware options installation 49
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3. Do one of the following:
o Extend the server from the rack (on page 20).
o Remove the server from the rack (on page 22).
4. Remove the access panel (on page 23).
5. Remove the air baffle (on page 24).
6. Disconnect all cables connected to existing expansion boards.
7. Remove the PCI riser cage ("Remove the PCI riser cages" on page 25).
8. Install the storage controller ("Installing a storage controller" on page 50).
9. Connect the common end of the Mini-SAS Y-cable to the controller option.
10. Install the PCI riser cage ("Install the PCI riser cages" on page 26).
11. Route the split ends of the Mini-SAS Y-cable along the side of the system board towards the front chassis,
and then connect the cable to the drive backplane.
12. Connect the rest of the drive cables required in this drive configuration. For more information, see
"Storage cabling (on page 83)."
13. If you intend to use an FBWC module and capacitor pack, install these options now ("Installing the
FBWC module and capacitor pack" on page 51).
14. Install the air baffle (on page 24).
15. Install the access panel (on page 24).
16. Install the server into the rack ("Installing the server into the rack" on page 33).
17. Power up the server (on page 20).
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
18. Install the drives ("Installing a hot-plug drive" on page 37).
Controller options
The server ships with an embedded Smart Array B120i controller. For more information about the controller
and its features, see the HP Dynamic Smart Array RAID Controller User Guide on the HP website
(http://www.hp.com/go/smartstorage/docs).
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- • 8+8-bay SFF drive model 8
- • 12-bay LFF drive model 8
- • 25-bay SFF drive model 8
- Front panel LEDs and buttons 9
- Rear panel components 10
- Item Description 11
- Rear panel LEDs and buttons 12
- System board components 13
- DIMM slot locations 14
- System maintenance switch 14
- Drive numbering 15
- Drive LED definitions 16
- FBWC module LED definitions 17
- Fan locations 19
- Operations 20
- Remove the access panel 23
- Install the access panel 24
- Remove the air baffle 24
- Install the air baffle 24
- Remove the PCI riser cages 25
- Install the PCI riser cages 26
- Optimum environment 28
- Temperature requirements 29
- Power requirements 30
- Server warnings and cautions 31
- Rack warnings 32
- Installing hardware options 33
- Registering the server 35
- Introduction 36
- Security bezel option 36
- Drive options 36
- Installing a hot-plug drive 37
- Rear drive cage options 38
- Drive cable options 46
- Mini-SAS cable option 47
- Mini-SAS Y-cable options 48
- Controller options 49
- Optical drive option 54
- Hot-plug fan module option 55
- Fan population guidelines 56
- 4. Do one of the following: 57
- Memory options 60
- HP SmartMemory 61
- DIMM identification 62
- Memory protection modes 63
- Memory population guidelines 64
- Installing a DIMM 66
- Processor option 67
- Expansion board options 72
- GPU power cable option 74
- Cabling 83
- 4 SFF SATA cabling 84
- 6 LFF SATA cabling 84
- 6 SFF SATA cabling 85
- 8 LFF cabling 85
- 8 SFF cabling 87
- 8+8 SFF cabling 89
- 12 LFF cabling 92
- 25 SFF cabling 94
- 2 LFF rear drive cabling 95
- 2 SFF rear drive cabling 96
- Capacitor pack cabling 97
- Cabling 98 98
- Optical drive cabling 99
- GPU power cabling 99
- Dual-rank GPU 100
- Primary GPU power cabling 100
- Secondary GPU power cabling 101
- Server mode 102
- HP product QuickSpecs 102
- HP iLO Management 102
- Active Health System 103
- Intelligent Provisioning 104
- HP Insight Diagnostics 105
- Erase Utility 105
- HP Insight Online 106
- HP Service Pack for ProLiant 107
- HP ROM-Based Setup Utility 108
- Boot options 109
- Configuring AMP modes 109
- Utilities and features 110
- ROMPaq utility 111
- Automatic Server Recovery 111
- USB support 111
- Keeping the system current 112
- Version control 113
- ProLiant servers 113
- Troubleshooting 115
- System battery replacement 116
- Regulatory information 118
- Electrostatic discharge 119
- Specifications 120
- Specification Value 122
- Support and other resources 126
- Customer Self Repair 128
- Reparo feito pelo cliente 130
- Acronyms and abbreviations 134
- Documentation feedback 138
- Index 139 139
- Index 140 140
- Index 141 141
- Index 142 142
Relacionado con productos y manuales para Hardware De La Computadora Hp ProLiant DL380e Gen8 Server
(110 paginas)
Hardware De La Computadora Hp Blade de servidor HP ProLiant BL495c G5 Manual de usuario
(95 paginas)
(95 paginas)
Hardware De La Computadora Hp Blade de servidor HP ProLiant BL685c G6 Manual de usuario
(117 paginas)
(117 paginas)
Hardware De La Computadora Hp Blade de servidor HP ProLiant BL490c G7 Manual de usuario
(112 paginas)
(112 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales