HP 8591C Manual de usuario Pagina 37
- Pagina / 550
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
I
-
I
-
Preparing For Use
Turning on the Analyzer for the First Time
1. To calibrate the tracking generator, connect the tracking generator output
(RF OUT 75
a2)
to the cable TV analyzer INPUT 75
D
connector, using an
appropriate cable.
NOTE
A low-loss cable should be used for accurate calibration. Use the 75
0
cable shipped with the cable
TV analyzer.
2. Press the following cable TV analyzer keys:
ICAL),
More 1 of 4 ,
More 2 of 4 , then CAL
TRK
GEM TG SIGNAL NOT FOUND will be
displayed if the tracking generator output is not connected to the cable TV
analyzer input.
3. To store this data in the area of cable TV analyzer memory that is stored
when the cable TV analyzer is turned off, press CAL STORE
When the self-calibration routines have been completed successfully, the cable
TV analyzer is ready for normal operation.
1-16
- User’s Guide 1
- Assistance 6
- Safety Notes 7
- General Safety Considerations 8
- Cable TV Analyzer 9
- Documentation Description 9
- Contents 12
- Preparing For Use 22
- More 2 of 4, and CAL TRK 25
- Inspection 26
- Requirements 28
- 81x-5182 33
- 3. Press 34
- cable shipped with the cable 37
- TV analyzer 37
- Printing 38
- Plotting 38
- Press @%FiQ, More 39
- Printing or Plotting 43
- Equipment 46
- Electrostatic 60
- Discharge 60
- Getting Started 62
- Front-Panel 64
- Features 64
- Rear-Panel 68
- Controls 71
- Fine-Focus Control 73
- Annotation 74
- PEAK SEARCH] or press 81
- Procedure to Change the 90
- Information 92
- Overwritten 105
- Press LOAD FILE 117
- (PRESET) 119
- Card -+ Trace AMP COR 124
- Limit-Line 125
- Functions 125
- FREQUENCY], 300 126
- Using limit-line Functions 128
- Selecting the Type of 132
- Limit-Line Table 132
- Selecting the Limit-Line 133
- Table Format 133
- Using Limit-Line Functions 137
- Selecting the Segment 138
- Limit4ine 140
- Functions 140
- FREQUENCY] 300 MHz 141
- I IHZ SWP 30.0 145
- FREQUENCY), START 145
- Amplitude-Correction 153
- 14:85:24 154
- AUG 18 154
- External 157
- Keyboard 157
- [BACKSPACE) 158
- External Keyboard 159
- Installation 160
- To Enter a Screen Title 160
- Making Basic 162
- Measurements Using 162
- Spectrum Analyzer Mode 162
- CFREQUENCY) 165
- FREQUENCY) 167
- 300 (MHz), then 167
- PEAK SEARCH_) 168
- Resolution Bandwidth 169
- FREQUENCY] 300 (MHz) 170
- SEARCH].) 170
- FREQUENCY], 300 (MHz) 172
- PEAK SEARCH) 174
- (MHz) 175
- FREQUENCY], 100 177
- FREQUENCY), START FREQ , 88 184
- AUTO COUPLE) and 185
- FREQUENCY), 400 192
- I I I I I I 194
- Third-Order 195
- Intermodulation 195
- Distortion 195
- SEARCH] 196
- Making Measurements 201
- Using Spectrum Analyzer 201
- (MEAS~USER) 203
- Figure 5-1. FFT Annotation 204
- AMPLITUDE] and 206
- FREQUENCY) and adjust the 207
- Analyzer 208
- Stimulus-Response 212
- Measurements 212
- SPECTRUM ANALYZER 215
- ATN AUTO 216
- Refer to 216
- Figure 5-9. Normalized Trace 221
- SEARCH) to 223
- Time-Gate Utility Display 228
- Gate Delay 239
- Signal Delay 239
- ENTER 50.08 MHz 250
- (FFEZT] 256
- N dB Bandwidth Measurement 260
- N dB Bandwidth Measurement 261
- Adjacent Channel Power 271
- Adjacent Channel Power Graph 272
- Measurement 274
- Channel Power 275
- Key Descriptions 277
- Diagnostic 280
- Service Diagnostic 281
- A. (Vertical lines on the 285
- A. (Vertical lines on 287
- Front-Panel Key Access 291
- (jD’spLAy-1 291
- AUTO COUPLE] 293
- AUTO COUPLE) 293
- CATALOG 0% 308
- 981861 AT 309
- COUPLE) or 311
- AMPLITUDE] 326
- Spectrum Analyzer Mode Key 328
- Oescriptions 328
- PEAK SEARCH] 333
- CAT ITEM 334
- Mode Functions 337
- this function is disabled 343
- FREQUENCY] 351
- Coupling, UPDATE TIMEFREQ 363
- SEARCH] 365
- FREQUENCY) then 366
- PEAK SEARCH) and 367
- PEAK SEARCH), MARKER A , and 367
- ZOOM the first 384
- Descrrptions 403
- [MEAS/USER) 409
- (MKRFCTN) 411
- AUTO COUPLE) or 416
- TRACKING 424
- [MEAS~USER) 426
- Key Menus 433
- If You Have a Problem 450
- More 1 of 4 455
- FREQUENCY), -37 458
- Messages 463
- AUTO COUPLE), AUTO ALL (U) 473
- Options and Accessories 478
- Accessories 484
- Glossary 488
- FM span, 6-74 525
- Index- 10 526
- Index- 11 527
- Index- 12 528
- Index- 13 529
- Index- 14 530
- Index- 15 531
- Index- 16 532
- Index- 17 533
- Index- 18 534
- Index- 19 535
- Index-20 536
- Index-22 538
- Index-23 539
- Index-24 540
- Index-25 541
- Index-26 542
- Index-27 543
- Index-28 544
- Index-29 545
- Index-30 546
- Index-32 548
- Index-33 549
- Index-34 550
Relacionado con productos y manuales para De medición, control y control HP 8591C
(228 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales