HP HP ProCurve Series 6600 Manual de usuario

Configuration of HP ProCurve Devices in aCampus EnvironmentBest Practice DocumentProduced by CESNET led working groupon Network monitoring(CBPD111) Au

10 1.9 Switch Management Access Addresses If these ranges are not set, the active device can be managed from any address. This applies to access via

11 Recommendation: Always verify the switch settings and set the access to restricted. Preferably use SNMPv3 if you want to write to relevant part

12 To make the login process easier it is possible to let the switch enter the privileged mode upon the first login. The administrator accessing the

13 Recommendation: Disable access to the switch via insecure protocols, i.e. telnet and http, if possible.

14 2 L2 Configuration 2.1 Setting the Communication Parameters of the Switch Port 2.1.1 Speed and Communication Parameters Switch port parameter co

15 or hp-test(config)# trunk b1-b4 trk1 lacp Displaying port status: hp-test(config)# show trunks Load Balancing Port | Name

16 2.1.4 Spanning Tree Spanning Tree is a protocol used to discover loops in switched networks and to remove such loops. To turn on STP on the swi

17 aaa port-access authenticator 1 auth-vid 578 aaa port-access authenticator 1 unauth-vid 589 aaa port-access authenticator 2 auth-vid 578 aaa

18 hp-test(config)# no lldp config A1 medTlvEnable poe hp-test(config)# no lldp config A1 medTlvEnable capabilities hp-test(config)# no lldp config

19 Recommendation: Only suppress the LLDP or CDP information broadcasting when it is really necessary. 2.2 VLAN Configuration 2.2.1 Assigning Por

2 © TERENA 2010. All rights reserved. Document No: GN3-NA3-T4-CBPD111 Version / date: March 2010 Original language

20 B6 Tagged Learn Down B7 Tagged Learn Down B8 Untagged Learn Down B9

21 Management VLAN : VLAN ID Name | Status Voice Jumbo ------- -------------------- + ---------- ----- ----- 1

22 Port Information Mode Unknown VLAN Status ---------------- -------- ------------ ---------- A6 Auto Learn Up

23 VLAN ID : 614 VLAN Name : vlan descr Querier Address : This switch is Querier Active Group Addresses Reports Queries Querier Access Port

24 hp-test(config)# dhcp-snooping hp-test(config)# dhcp-snooping authorized-server 10.229.206.2 hp-test(config)# dhcp-snooping authorized-server 10

25 3 Basic L3 Configuration This section describes only the basic L3 configuration of the switch. 3.1 Configuring IP Addresses on VLAN hp-test(conf

26 3.4 Assigning to OSPF hp-test(config)# vlan 240 hp-test(vlan-240)# ip ospf area 0.0.0.2 hp-test(vlan-240)# ip ospf passive hp-test(config)# rout

27 hp-test(config)# vlan 614 hp-test(vlan-614)# ip igmp hp-test(vlan-614)# ip pim-dense hp-test(vlan-614-pim-dense)# exit 3.6.2 PIM - Rendezvous Po

28 hp-tech# show ip pim neighbor PIM Neighbors IP Address VLAN Up Time (sec) Expire Time (sec) --------------- ---- ----------

29 233.4.200.11 147.229.196.2 147.229.252.114 619 233.4.200.11 147.229.200.2 147.229.252.121 621 233.4.200.11 147.229.205.2 147

3 Table of Contents Table of Contents 3 Executive Summary 5 1 Basic Settings and Operations 6 1.1 Switch Access 6 1.2 Resetting to Factory Defau

30 4 Auxiliary Tools 4.1 Automated Configuration Download This script enables an automatic loading of current switch configuration over SSH. This sc

More Best Practice Documents are available at www.terena.org/campus-bp/ [email protected]

4 3.5 DHCP Relay 26 3.6 Multicast Routing 26 3.6.1 PIM Dense Mode 26 3.6.2 PIM - Rendezvous Point (RP) 27 3.6.3 PIM Sparse Mode 27 3.6.4 Displa

5 Executive Summary This document describes the basic configuration of HP switches in a campus environment. Switches have a fairly large number o

6 1 Basic Settings and Operations 1.1 Switch Access The switches in the HP ProCurve series feature several configuration interfaces - w

7 1.3 Firmware Upgrade Firmware upgrade is a very important step. Always check if a newer firmware version has been released before installing new

8 Validating and Writing System Software to the Filesystem ... hp-test# We reboot the switch and choose the secondary flash for the next boot

9 1.5 Setting Passwords This command will set the basic switch passwords for access by administrators and operators. The switch manag