Hp Integrity Superdome 2 Server Manual de usuario

HP Integrity Superdome 2 OnboardAdministrator Command Line Interface UserGuideAbstractThis document contains specific information that is intended for

RS...190SEL...

1 iLO-00237dd565f4 16.93.73.240 OK On Off 2 iLO-00237dd55598 15.255.103.130 OK On Off 3 iLO-00

NOTE: SERVER is a valid alias for BLADE.• Description:Displays the port mapping for the blade specified by the bay number• Access level/Bay level:All◦

• Restrictions:You must have access to the specified bay number.• Example:OA-0018FE27577F> SHOW SERVER POWERDELAY ALLCurrent PowerDelay Status: Not

• Access level/Bay level:All• Restrictions:None• Example:sphere-oa2> show blade status 1Blade #1 Status: Power: On Current Wattage us

15 IOX enclosure management commandsSHOW IOX INFO• Command:SHOW IOX INFO { ALL | <iox_number> {[ - | , ] <iox_number>} }• Description:Dis

SHOW IOX LIST• Command:SHOW IOX LIST• Description:Displays the IOX enclosure list.• Access level/Bay level:All• Restrictions:None• Example:oa-hostname

SHOW IOX STATUS• Command:SHOW IOX STATUS { ALL | <iox_number> {[ - | , ] <iox_number> }}• Description:Displays IO expansion enclosure stat

Link 2: OK ... Link N: FAILED IO Slots Status: Bay Slot Status ---- ---- -----------------

16 Interconnect management commandsASSIGN INTERCONNECT• Command:ASSIGN INTERCONNECT {ALL | <bay number> [{ , | - } <bay number>]} {"&

POWEROFF INTERCONNECT• Command:POWEROFF INTERCONNECT {ALL | <bay number> [{ - | , } <bay number>]}• Description:Sends a request to power o

1 Accessing the CLIRemotely accessing the Onboard AdministratorThe Onboard Administrator CLI can be accessed remotely through any Telnet or Secure She

SET INTERCONNECT POWERDELAY• Command:SET INTERCONNECT POWERDELAY {ALL | <bay number> [{ - | , } <bay number>]} {number of seconds to delay

SHOW GPSM INFO• Command:SHOW GPSM INFO { ALL | <gpsm_number> {[ - | , ] <gpsm_number>} }• Description:Displays:◦ Model◦ Manufacturer◦ Part

Unit Identification LED: Off Diagnostic Status: Internal Data OK Management Processor OK

Internal Ethernet Route to OA: Enabled Internal Serial Interface to OA: Absent Internal Serial Route to OA: Disabled Exte

SHOW INTERCONNECT PORT MAP• Command:SHOW INTERCONNECT PORT MAP {ALL | <bay number> | <bay number>-<bay number>}• Description:Display

1 Cisco Catalyst Blade Switch 3120 Disabled 2 Absent Disabled 3 Absent

• Description:Displays:◦ Model◦ Manufacturer◦ Part Number◦ Spare Part Number◦ Serial Number◦ Engineering Date Code◦ Firmware Bundle Revision• Access l

SHOW XFM LIST• Command:SHOW XFM LIST• Description:Displays the Xbar Fabric module list.• Access level/Bay level:All• Restrictions:None• Example:sphere

Link 7: Unknown Link 8: Unknown118 Interconnect management commands

17 Enclosure DVD commandsSHOW DVD INFO• Command:SHOW DVD INFO• Description:Displays:◦ Model◦ Manufacturer◦ Part Number◦ Spare Part Number◦ Serial Numb

1. Connect a serial cable between the serial port on the computer and the corresponding serialport on the Onboard Administrator module. The following

Unit Identification LED: Off Diagnostic Status: Internal Data OK Power OK

18 Remote syslog commandsDISABLE SYSLOG REMOTE• Command:DISABLE SYSLOG REMOTE• Description:Disables remote system logging• Access level/Bay level:OA A

• Access level/Bay level:OA Administrator, OA Operator• Restrictions:NoneSHOW SYSLOG SETTINGS• Command:SHOW SYSLOG SETTINGS• Description:Displays the

19 USB support commandsDOWNLOAD CONFIG using USB key• Command:DOWNLOAD CONFIG <url>• Description:Downloads a saved configuration file from a spe

UPLOAD CONFIG using USB key• Command:UPLOAD CONFIG { "<url>" | ARCHIVE "<filename>" | USB "<filename>"

20 iCAP commandsFor more information on using iCAP commands, see the HP Instant Capacity user guide for Version10.x.ICAPSTATUS• Command:ICAPSTATUS• De

ICAPMODIFY• Command:ICAPMODIFY• Description:Allows setting some configuration options, including notification email address and iCAPsystem ID.◦◦ Allow

• Access level/Bay level:Operator or Admin• Restriction:You must be connected to the monarch OA.ICAPMODIFY 127

21 Partition commandsFor more information on using Partition commands, see the HP Integrity Superdome 2 PartitioningAdministrator Guide.ASSIGN PARCON_

UNASSIGN PARTITION• Command:UNASSIGN PARTITION { ALL | <nPartition Number>[:<vPartition Number>] [ , <nPartition Number:<vPartition

2 Command lineCommand line overviewYou can also use the CLI to manage the Onboard Administrator. The following are some reasonsto use the CLI:• HP Man

MeaningOptionSpecify an optional name for the new nPartition. If aname is not specified, a default name of Par <4 digitnPartition number> is giv

MeaningOptionSpecifies whether Hyper-Threading should be enabledor not. The valid values for flag are:[-T flag]◦ y — enables Hyper-Threading, which al

MeaningOptionrequested resources specified in the parspec is notavailable for assignment to the partition at boot time.Enable/Disable VGA in an nParti

The options for the command:MeaningOptionThe nPartition to modify. The nPartition id can bespecified as an nPartition number or an nPartition name.[-p

MeaningOptionSpecify the OS to be used in the nPartition. This is usedto determine the default values for certain firmware andmemory settings. The val

• Access level/Bay level:OA Administrator, OA Operator• Restriction:◦ You must be connected to the monarch OA.PARREMOVE• Command:parremove {-p nPart

[-A] [-M] parstatus {-P} [-Z] [-v] [-M] parstatus {-i IOresource}... [-M] [-V] parstatus {-c blade }} ... [-M] [-V] parstatus {-e e

MeaningOptionDisplays information for specified I/O resource.{-i IOresource]Displays information for all I/O resources in the complexincluding I/O on

Current Product Order Number: AH337AOEM Manufacturer: N/ATotal number of partitions present: 1[Enclosure]Enclosure Enclosure Num Num Bay Enclo

POWEROFF PARTITION• Command:POWEROFF PARTITION {{<nPar ID>} [:<vPar ID>] [FORCE] [OVERRIDE] | ALL [FORCE] }• Description:Gracefully shuts

the Onboard Administrator. You can only change the password for the Administrator account. Thefollowing table indicates the capabilities of the user b

• Access level/Bay level:OA Administrator, OA Operator• Restriction:nPar ID and vPar ID can either be the name or number of the nPartition or virtualp

• Restriction:You must be connected to the monarch OA.◦◦ In multi-enclosure systems, the enclosure number the DVD drive is installed can be specifieda

1 Npar001 Yes 11 Npar001 No 22 Backup No 13:1 vpar0301 - No iLO

TOC PARTITION• Command:TOC PARTITION {<nPar ID>} [:<vPar ID>]} [OVERRIDE]• Description:Performs a transfer-of-control reset of the specifi

MeaningOptionSpecifies the default setting for Hyper-Threading in annPartition. The valid values for flag are:[-T flag]◦ y — enables Hyper-Threading,

VPARCREATE• Command:vparcreate [-p vparidentstr] [-a rsrc]... [-Z parspecname] [-N nparidentstr] [-P vp_name]• Description:Creates a new virtual part

MeaningOption–n is not specified. –z and –n are mutually exclusive.The default parspec is modified with the –n option.Specifies a name for the new vir

MeaningOptionspecified, a vPar name in the format <vPar.vPar_num>is automatically assigned to the created virtual partition.NOTE: The name for t

MeaningOptionSpecifies the parspec of the nPar in which the vPar isto be modified. When this option is specified all other-Z parspecnamecommand option

MeaningOptionThe force option, this option is required and is used asconfirmation before resetting the virtual partition.NOTE: On Superdome 2, the for

Bays selected forthis accountAccount name/privilegelevelCapabilitiesAccount classificationown account• Can 'show' CLI commandsPartition mana

MeaningOptionremove the vPar in that nPar. If the –n option is notspecified. nparidentstr can be specified as an nParname or nPar number.• Access leve

MeaningOptionSpecifies the partition specification from which the virtualpartition database has to be chosen.NOTE: When a current parspec is examined

22 Log viewer commandsCLEAR FPLCAUTION: You cannot restore this information after you delete it.• Command:CLEAR FPL• Description:Clears the Forward Pr

CONNECT PARTITION• Command:CONNECT PARTITION [VIEWONLY] {<nPar ID>[:<vPar ID>]}• Description:Connects to the text console for the specifie

NOTE: To view the entire Console Log while in the Console Log Viewer, first enter g followedby 2200000 (the maximum size of a Console Log).• Access le

23 Health Repository commandsHP Integrity Superdome 2 complexes use the HP Integrity Superdome 2 Analysis Engine to provideerror handling, logging, an

DIMMERR• Command:DIMMERR <physical location>• Description:Displays all errors experienced by DIMMs on a specified blade or all errors for a spec

NOTE: The DIMM error table for indicted DIMMs is also displayed as part of the output from theshow <memory_location> command.Location Installati

SHOW ACQUIT• Description:Lists all recently acquitted indicted components for the complex, with the following information:◦ Component Type◦ Physical L

• Access level/Bay level:All• Restrictions:Must be in the Health Repository viewer.• Example:myhost HR> show deconfigSystem Acquittal History - Mon

LDAP users• The Enable/Disable LDAP is an optional setting. LDAP enabled can be used with local usersenabled or disabled.• The Onboard Administrator u

◦ Reason for the indictment◦ State of the component• Access level/Bay level:All• Restrictions:Must be in the Health Repository viewer.• Example:myhost

• Restrictions:The <physical location> value must be formatted as either an 8–byte hexadecimalinteger, or a long or medium hardware resource pat

The test camnet all command will execute the global CAMNet test after first checkingthat there are no partitions active.• Access level/Bay level:All•

• Restrictions:◦ Must be in the Health Repository viewer.• Example:myhost-HR> test clocksClocks test started...Blade Sys Clk 0 Sys Clk 1==========

24 Core Analysis Engine commandsThe Core Analysis Engine is a component of the HP Integrity Superdome 2 Analysis Engine thatenables users to review al

Table 1 List of <arguments> (continued)Can beusedwith:ExamplesDescriptionArgument-L-v Processor,Memory: Displays allevents in the categories Pro

Table 1 List of <arguments> (continued)Can beusedwith:ExamplesDescriptionArgument-LSorts the displayed list of resultsby the specified column na

Managed Entity : OA Name : Not Available System Type : 0 System Serial No. : Not Available OA IP Ad

25 Error Logging Services commandsSHOW ERRDUMP• Command:SHOW ERRDUMP {<logtype> [nPar:<nPar #>] | dir <logtype> | bundle_id <bund

26 Debug commandsDISABLE OSDEBUGGER• Command:DISABLE OSDEBUGGER• Description:Disables debugger ports on all complex partitions.• Access level/Bay leve

3 General commandsCLEAR SCREEN• Command:CLEAR SCREENNOTE: CLS is also a valid command.• Description:Clears the terminal screen• Access level:AllEXIT•

27 Firmware update commandsFor information on online firmware update using the OA GUI, see the HP Integrity Superdome 2Onboard Administrator User Guid

UPDATE SHOW FIRMWARE• Command:UPDATE SHOW FIRMWARE• Description:Displays the firmware versions of the complex bundle last installed in the complex and

nPartition Enc Bay Version 2 | 2 | 3 | 1.0.02 | 2 | 4 | Invalid◦ Partition — The nPartition number the row is

The <uri> can be any of the following:◦ http://host/path◦ ftp://host/path◦ ftp://username:password@host/path◦ tftp://host/path◦ For the USB thum

XFM | 1 | 1 | 1.1.0You can abort this update by pressing ^C within 10 seconds.Updating devices... DO NOT remove or power cycle device(s)!

Firmware update SUCCESSFUL.If the update is unable to start the system prints:Firmware update CANCELLED by system, no firmware modified.If the update

28 Updating FirmwareIntroductionSuperdome 2 firmware update uses a smart analysis algorithm to assist and prevent disabling aSuperdome 2 through bad f

All partitions updateUse the following command to update all partitions present in the system as well as any bladesthat are not currently assigned to

Please note that Superdome 2 systems running a firmware bundle released prior to (numberedlower than) 2.2.27 do not possess the capability to perform

• parmodify• parstatus• cplxmodify• vparcreate• vparremove• vparmodify• vparboot• vparreset• vparstatus• icapmodify• icapstatus• plg9hlth• seedGlobalM

LOGOUT• Command:LOGOUT• Description:Exits the command line interface• Access level:AllQUIT• Command:QUIT• Description:Exits the command line interface

System Firmware Services During Boot, Shutdown, etc.Certain partition events which occur while the OS is running may not be handled if they occurwhile

• SOAP request from GiCAP Group Manager, HP-SUM• Kernel debugger connection through OA network port• Console access through the OA• Ping, SNMP queries

hpvminfo command qualifiers failThe use of certain hpvminfo command qualifiers will return an ioctl error when executed duringSuperdome 2 Online Firmw

par* and vpar* commands failParcon services are not available during Superdome 2 Online Firmware Update. Due to thisunavailability, all par* and vpar*

Errors during updateIf the firmware update analysis detects that the applied partition firmware does not meet bothmandates, the update will print an e

29 Archive Storage commandsThese commands implement the archive storage feature.Archive Storage provides direct access to the local internal thumbdriv

oa-host-name> clear archiveThis command will erase ALL files from the Archive Storage.Entering anything other than 'YES' will result in t

The url should be formatted as protocol://host/path/<file>. If your ftp server does not supportanonymous connections then you can specify a user

• Restrictions:The filename parameter must not contain any spaces and must have a .pmc extension.◦◦ You must be connected to the monarch OA to perform

30 Legacy console commandsThese commands are carried forward from previous systems to provide additional functionality forusers. These commands functi

4 Rack commandsSET RACK NAME• Command:SET RACK NAME <rack name>• Description:Sets the rack name• Access level/Bay level:OA Administrator, OA Ope

FPL• Command:fpl• Description:Equivalent to “SHOW FPL” (page 153).• Access level/Bay level:OA Administrator, OA Operator• Restrictions:You must be con

TC• Command:tc [<nPar #>]• Description:Enables users to TOC reset a partition.If <nPar #> is specified, then this command is equivalent to

31 Event notificationsEnclosure event notificationsEnclosure events produce screen messages with the SHOW DISPLAY EVENTS option enabled. Ifyou are dir

CauseEventAn interconnect module was inserted into an enclosure.Interconnect InsertedThe thermal status of an interconnect module changed.Interconnect

32 Support and other resourcesBefore you contact HPBe sure to have the following information available before you call HP:• Technical support registra

initiate a fast and accurate resolution, based on your product’s service level. Notifications may besent to your authorized HP Channel Partner for on-

| Separates items in a list of choices.WARNING! A warning calls attention to important information that if not understood or followedwill result in pe

A Using event logsEvent logs are generated by software or firmware when an event is detected. Some events thatcause event records to be generated are:

◦ alert level◦ hexadecimal dump of event records◦ event ID keyword• Raw hex – The raw hex format supplies following information about an event:◦ hexad

Rep Location nPar: AL Encoded Field Data Field KeywordEnt vPar TimestampSFW

© Copyright 2011 – 2013 Hewlett-Packard Development Company, L.P.NoticesThe information contained herein is subject to change without notice. The only

• Restrictions:You must be logged on to the monarch OA to perform this command.• Example:The output for this command will depend on how the enclosures

NOTE: The display of column headers can be turned on or off using toggle option C. By default,the column header will be on.To connect to the FPL viewe

number of connections supported by the OA. Each SEL viewer works independently from any otherviewer, meaning that each SEL viewer can select its own f

S: Cause/Action The following alert threshold options are available: Alert thresholds will cause events at the selected threshold

Deconfiguration is the act of disabling a component in the system. This happens when analysisfinds that a component has a serious fault. A components

IMPORTANT: In most cases resumption of function will not cause automatic acquittal.Component replacement, complex AC power cycle or manual acquittal i

--- end report --- 2 records shownNOTE: The requested and current deconfiguration states shown in the examples above are notthe same. This can happen

Timestamp: Thu Sep 10 18:34:12 2009 Serial Num: MYJ84901ZH Parent Serial: 1Z34AB7890 Part Num: AH342-60003 Spare Part Num:

B Time zone settingsUniversal time zone settingsNOTE: Time zones must be entered exactly as they appear.The following table provides the Universal tim

Americas time zone settingsNOTE: Time zones must be entered exactly as they appear.The following table provides the Americas time zone settings that a

Canada/YukonAmerica/NomeAmerica/EirunepeChile/ContinentaAmerica/NoronhaAmerica/El_SalvadorChile/EasterIslandAmerica/PanamaAmerica/EnsenadaCubaAmerica/

UPLOAD DEBUG• Command:UPLOAD DEBUG { <URL> | ARCHIVE <"directory"> | USB <"directory"> }• Description:This comma

TurkeyAsia/UlaanbaatarAsia/RangoonAsia/KabulAsia/BruneiAsia/Ulan_BatorAsia/RiyadhAsia/KamchatkaAsia/CalcuttaAsia/UrumqiAsia/Riyadh87Asia/KarachiAsia/C

The following table provides the European time zone settings that are supported by the OnboardAdministrator.Europe/VaduzEurope/ParisEurope/HelsinkiEir

Standard terms, abbreviations, and acronymsBIOS Basic input/output system.CA certificate authority.CAE Core Analysis Engine.CPU Central processing uni

Xbar Crossbar.XFM Xbar Fabric module.XML Extensible markup language.213

IndexAaccount authentication, 15account level, 13ACQUIT, 155ADD EBIPA, 51ADD HPSIM CERTIFICATE, 42ADD LDAP CERTIFICATE, 34ADD LDAP GROUP, 34ADD OA DNS

ENABLE USER, 24ENABLE XMLPREPLY, 62Enclosure Bay IP Addressing (EBIPA) commands, 51enclosure DVD commands, 119enclosure information, 192enclosure mana

restrictions, Server blade, 13RS, 190SSecure Shell session, 11SEL, 190serial port, 11server blade failure errors, 192Server blade restrictions, 13SET

SHOW OA , 86SHOW OA CERTIFICATE, 86SHOW OA INFO, 87SHOW OA NETWORK, 87SHOW OA STATUS, 88SHOW PARTITION CONSOLELOG, 153SHOW PARTITION DVD, 141SHOW PART

5 User account commandsADD USER• Command:ADD USER "<user name>" ["<password>"]• Description:Adds a user to the system.

ASSIGN OA• Command:ASSIGN OA {"<user name>" | LDAP GROUP "<LDAP group name>"}• Description:Assigns the Onboard Adminis

ENABLE STRONG PASSWORDS• Command:ENABLE STRONG PASSWORDS• Description:When enabled, this command requires that a user's password contain at least

REMOVE USER• Command:REMOVE USER {ALL | "<user name>" | CERTIFICATE "<user name>"}• Description:Removes a user from th

SET SESSION TIMEOUTIMPORTANT: On Superdome 2 systems, the following long-running commands are not immediatelysubject to the session timeout defined by

• Access level/Bay level:All users can modify their own contact information.◦◦ The OA Administrator can modify all users.• Restrictions:The <user n

◦ The character set includes all printable characters.◦ You must specify the password when in SCRIPT MODE.SHOW PASSWORD SETTINGS• Command:SHOW PASSWOR

• Access level/Bay level:All• Restrictions:The <user name> is case-sensitive. Users who do not have OA Administrator or OA Operatoraccess levels

Contents1 Accessing the CLI...11Remotely accessing the Onboard Admin

UNASSIGN OA• Command:UNASSIGN OA {"<user name>" | LDAP GROUP "<LDAP group name>"}• Description:Removes the Onboard Adm

6 Two-Factor Authentication commandsDISABLE CRL• Command:DISABLE CRL• Description:Disables certificate revocation checks• Access level/Bay level:OA Ad

DOWNLOAD USER CERTIFICATE• Command:DOWNLOAD USER CERTIFICATE "<user name>" <url>• Description:Downloads an x.509 certificate for

• Access level/Bay level:All• Restrictions:None• Example:OA-0016355E560A> SHOW CA CERTIFICATEDetails for ca certificate 1certificateVersion

7 Directory commandsADD LDAP CERTIFICATE• Command:ADD LDAP CERTIFICATE <end marker> <certificate> <end marker>• Description:Adds an

• Access level/Bay level:OA Administrator• Restrictions:NoneASSIGN OA LDAP GROUP• Command:ASSIGN OA {"<user name>" | LDAP GROUP "

ENABLE LDAPNOTE: If LDAP is enabled, local accounts are disabled, and the LDAP server becomes unavailable,you can recover by booting into Lost Passwor

SET LDAP GROUP ACCESS• CommandSET LDAP GROUP ACCESS "<group name>" {ADMINISTRATOR | OPERATOR | USER}• Description:Sets the LDAP group

SET LDAP PORT• Command:SET LDAP PORT <port number>• Description:Sets the TCP port number of the LDAP SSL service. Port 636 is the standard value

• Restrictions:None• Example:OA-0016355E560A> SHOW LDAP CERTIFICATE1 Certificate name: 17D6A5ECBF51A1A47D44C1CDD29D19EE.pem-----BEGIN CERTIFICATE--

REMOVE CA CERTIFICATE...32REMOVE USER CERTIFICATE..

• Restrictions:None• Example:OA-0018FE27577F> SHOW LDAP INFODirectory Services (LDAP) Enabled : Disabled Local User

UNASSIGN OA LDAP GROUP• Command:UNASSIGN OA {"<user name>" | LDAP GROUP "<LDAP group name>"}• Description:Disables acc

8 HP SIM commandsADD HPSIM CERTIFICATE• Command:ADD HPSIM CERTIFICATE <end marker> <certificate> <end marker>• Description:Adds an H

SET HPSIM TRUST MODE• Command:SET HPSIM TRUST MODE {CERTIFICATE [ON] | DISABLED [OFF]}• Description:Enables or disables the HP SIM SSO mode. When enab

9 General management commandsDOWNLOAD OA CERTIFICATE• Command:DOWNLOAD OA CERTIFICATE [<bay number>] <url>• Description:Downloads a CA sup

Generate certificate promptsRestrictionsDescriptionPromptMust be 1 to 60 characters long. To preventsecurity alerts, the value of this field must matc

• Access level/Bay level:All• Restrictions:The <ip address> must be in the form ###.###.###.###, where each ### ranges from0 to 255.SET DEVICE S

SET SCRIPT MODE• Command:SET SCRIPT [MODE] {ON | OFF}• Description:Ceases all prompting and verifying of entries when SCRIPT MODE is on.◦◦ The ADD USE

SHOW SERVER STATUS ALLSHOW SERVER TEMP ALLSHOW PARTITION DVDSHOW SERVER POWERDELAY ALLSHOW SERVER BOOT ALLSHOW SYSLOG SERVER ALLSHOW SYSLOG ILO ALLSHO

• Access level/Bay level:All◦◦ Bay specific• Restrictions:Dependent on bay privileges• Example:OA-0016355E560A> SHOW DEVICE SERIAL_NUMBER BLADESeri

11 Enclosure network configuration commands...55ADD OA DNS...

• Access level/Bay level:◦ OA Administrator, OA Operator• Restrictions:None• Example:[MFG Shell Enabled]iduno-oa> show user sessionsUsername A

10 Enclosure Bay IP Addressing commandsADD EBIPA• Command:ADD EBIPA { BLADE | INTERCONNECT } DNS <ip address> [ { , | - } <baynumber> ]NOT

NOTE: SERVER is a valid alias for BLADE.• Description:Enables the Onboard Administrator to provide IP addresses to the devices in the bays usingDHCP.I

If no bays are specified when setting the <ip address>, then all the bays are assigned anIP address in the range starting from the <ip addres

4A No 0.0.0.0 4B No 0.0.0.0 5 No 0.0.0.0 0.0.0.0 5A No 0.0.0.0 5B No 0.0.0.0 6 No

11 Enclosure network configuration commandsADD OA DNS• Command:ADD OA DNS [<bay number>] <ip address>• Description:Adds an IP address of a

• Access level/Bay level:Administrator• Restrictions:SSHKEY is only available for the Administrator local account.◦◦ The SSHKEY string is limited to 8

OA Bays• Restrictions:All blades in the enclosure must be powered off before clearing the VCMODE.◦◦ The enclosure is no longer managed by Virtual Conn

DISABLE SECURESH• Command:DISABLE SECURESH• Description:Disables SSH access to the Onboard Administrator.Disabling SSH prevents access to the web-base

DISABLE TRUSTED HOST• Command:DISABLE TRUSTED HOST• Description:Disables the host-based access to the Onboard Administrator. Disabling TRUSTED HOSTSal

POWERON XFABRIC...72RESTART OA ...

To execute a configuration script from a USB key, use usb://<directory name>/<scriptfile name>.To execute a configuration script from arch

• Access level/Bay level:OA Administrator, Operator• Restrictions:When using enclosure IP mode, only replace the standby OA module while the enclosure

ENABLE TELNET• Command:ENABLE TELNET• Description:Enables Telnet access to the Onboard Administrator• Access level/Bay level:OA Administrator, OA Oper

TEST WSMAN• Command:TEST WSMAN• Description:Sends a test WS-Management notification to subscribed clients.• Access level/Bay level:OA Administrator• R

REMOVE TRUSTED HOST• Command:REMOVE TRUSTED HOST <ip address>• Description:Removes an IP address from the list of systems permitted to connect t

• Access level/Bay levelAdministrator, OA Operator• Restrictions:The <ip address> must be in the form ###.###.###.###, where each ### ranges fro

• Access level/Bay level:All• Restrictions:NoneSET IPCONFIG• Command:SET IPCONFIG {DHCP | STATIC} [<OA bay number>] [DYNAMICDNS] <ip address&

◦ The default read community name is public.◦ The default write community name is public.SET SNMP CONTACT• Command:SET SNMP CONTACT "<contact&

◦ SSH status◦ Telnet status◦ NTP status◦ Trusted Host status◦ HPSIM Trust Mode status◦ AlertMail status◦ XML Reply status◦ WSMan status◦ Link Loss Fai

SHOW SNMP• Command:SHOW SNMP• Description:Displays:◦ Status◦ SNMP system name◦ Location◦ Contact◦ Read community name◦ Write community name◦ List of t

SHOW BLADE POWERDELAY...101SHOW BLADE STATUS...

SHOW SSHKEY• Command:SHOW SSHKEY• Description:Displays the contents of the existing SSH authorized key files• Access level/Bay level:Administrator• Re

12 Enclosure management commandsCLEAR SYSLOGCAUTION: You cannot restore this information after you delete it.• Command:CLEAR SYSLOG {ENCLOSURE | OA &l

• Access level/Bay level:OA Administrator• Restriction:NoneENABLE LLF• Command:ENABLE LLF• Description:Enables Link Loss Failover for Onboard Administ

RESTART OA• Command:RESTART OA [<bay number>]• Description:Resets the Onboard Administrator module specified by <bay number>. If no bay nu

SET ENCLOSURE NAME• Command:SET ENCLOSURE NAME "<enclosure name>"• Description:Changes the enclosure name.◦◦ The default enclosure nam

SET ENCLOSURE SERIAL_NUMBER• Command:SET ENCLOSURE SERIAL_NUMBER "<serial number>"• Description:Sets the enclosure serial number.• Acc

SET POWER MODE• Command:SET POWER MODE {NOTREDUNDANT | REDUNDANT | POWERSUPPLY}• Description:Configures power settings to ensure a specified level of

◦ The Dynamic Power Savings mode is established at the complex level and is managedfrom the Monarch OA. A change in Dynamic Power Savings mode is prop

SET TIMEZONE CST6CDT#SET DATE MMDDhhmm{{CC}YY}#Set Enclosure InformationSET ENCLOSURE ASSET TAG ""SET ENCLOSURE NAME "sphere"SET R

• Restrictions:None• Example:OA-0018FE27577F> SHOW DISPLAY EVENTSDisplay Events is set to OFF.SHOW ENCLOSURE FAN• Command:SHOW ENCLOSURE FAN {<f

PARCREATE...129PARMODIFY...

◦ Enclosure part number◦ Serial number◦ UUID◦ Asset tag◦ Midplane spare part number◦ Solutions ID◦ Power Distribution Unit information◦ Onboard Admini

Status: OK Display: On Name: BladeSystem c7000 Insight Display Spare Part Number: 441203-001 Manufacturer: HP

sphere-oa2> show enclosure powersupply 1Power Supply #1 Information: Status: OK AC Input Status: OK Capacity: 2400 Watts

Fan 3: 14000 RPM (78%) Fan 4: 14000 RPM (78%) Fan 5: 14000 RPM (78%) Fan 6: 14000 RPM (78%) Fan 7: 14000 RPM (78%) Fan 8: 14000 RPM (78%) Fan 9: 1400

SHOW FRU• Command:SHOW FRU• Description:The FRU Summary section provides information on all field replaceable units within theenclosure.◦◦ Information

Manufacturer: HP Serial Number: IL21300010 PCA Serial Number: IL21300010 Part Number: 661692-001 Spare Part Number

Serial Number: 543543861 Firmware Bundle Revision: 2.5 Engineering Date Code (EDC): XA01SHOW OA• Command:SHOW OA {CERTIFICATE |

SHOW OA INFO• Command:SHOW OA INFO [ALL | <bay number> [{ , | - } <bay number>]]• Description:Displays information about the Onboard Admin

Enclosure IP Mode: Not SupportedSHOW OA STATUS• Command:SHOW OA STATUS [ALL | <bay number> [{ , | - } <bay number>]]• Description:

SHOW SYSLOG• Command:SHOW SYSLOG {BLADE <bay number> | ENCLOSURE | OA <bay number> | SETTINGS}NOTE: SERVER is a valid alias for BLADE.• De

SHOW INFO...172UPDATE FIRMWARE ...

SHOW SYSLOG OA• Command:SHOW SYSLOG OA [<bay number>]• Description:Displays the syslog for the Onboard Administrator. If no bay number is given,

SHOW VCMODE• Command:SHOW VCMODE• Description:Displays Virtual Connect Mode settings• Access level/Bay level:All• Restrictions:None• Example:OA-0018FE

13 Complex management commandsCLEAR NTP• Command:CLEAR NTP {PRIMARY | SECONDARY}• Description:Disables access to the Primary or Secondary NTP server•

RESTART COMPLEXCAUTION: This command ungracefully halts all processing across the HP Integrity Superdome 2complex. This can cause partitions in the co

SET DATE• Command:SET DATE MMDDhhmm [[CC]YY][TZ]• Description:Sets the date of the complex with the following definitions:◦ MM: Month◦ DD: Day◦ hh: Ho

SET NTP SECONDARY• Command:SET NTP SECONDARY <ip address>>• Description:Sets the secondary server used for synchronizing time and date using

Serial Number: Unset Complex Type: 03000102 Configured Complex FW Revision: 0.6.35 SHOW COMPLEX STATUS• Command:SHOW COMPLEX STA

14 Blade management commandsSET NIC• Command:SET NIC {AUTO | FORCED}• Description:Configures the external NIC for auto-negotiation or forced link sett

SHOW BLADE INFO• Command:SHOW BLADE INFO {ALL | <bay number> [{ , | - } <bay number>]}NOTE: SERVER is a valid alias for BLADE.• Descriptio

Firmware Bundle Revision: 0.6.35 nPartition Revision: Unknown cpusocket-1/1/0: Intel Itanium 9300 series 1330 MHz