Hp ProLiant DL365 Server Manual de usuario Pagina 31
- Pagina / 116
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Hardware options installation 31
Hardware options installation
In this section
Introduction ........................................................................................................................................... 31
Processor option..................................................................................................................................... 31
Memory options..................................................................................................................................... 36
Hot-plug SAS and SATA hard drive options............................................................................................... 38
Multibay device options .......................................................................................................................... 41
Redundant hot-plug power supply option................................................................................................... 42
Expansion board options ........................................................................................................................ 44
HP Smart Array controller options ............................................................................................................ 47
Introduction
If more than one option is being installed, read the installation instructions for all the hardware options
and identify similar steps to streamline the installation process.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and
the internal system components to cool before touching them.
CAUTION: To prevent damage to electrical components, properly ground the server before beginning any
installation procedure. Improper grounding can cause electrostatic discharge.
Processor option
The server supports single- and dual-processor operation. With two processors installed, the server
supports boot functions through the processor installed in processor socket 1.
The server uses embedded PPMs as DC-to-DC converters to provide the proper power to each processor.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and
the internal system components to cool before touching them.
CAUTION: To prevent possible server malfunction and damage to the equipment, multiprocessor
configurations must contain processors with the same part number.
CAUTION: To avoid damage to the processor and system board, only authorized personnel should attempt
to replace or install the processor in this server.
CAUTION: To avoid damage to the system board:
• Do not touch the processor socket contacts.
• Always install the processor socket cover after removing the processor from the socket.
• Do not tilt or slide the processor when lowering the processor into the socket.
CAUTION: To avoid damage to the processor:
• Handle the processor only by the edges.
• Do not touch the bottom of the processor, especially the contact area.
- HP ProLiant DL365 Server 1
- User Guide 1
- Audience assumptions 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Rear panel components 9
- Rear panel LEDs and buttons 10
- System board components 11
- System maintenance switch 12
- NMI jumper 12
- SAS and SATA device numbers 14
- SAS and SATA hard drive LEDs 15
- Fan locations 16
- Operations 18
- Remove the access panel 20
- Install the access panel 20
- Operations 23 23
- In this section 24
- Rack planning resources 25
- Optimum environment 25
- Temperature requirements 26
- Power requirements 26
- Rack warnings 27
- Installing hardware options 27
- Registering the server 30
- Introduction 31
- Processor option 31
- Memory options 36
- Memory configurations 37
- Advanced ECC memory 37
- Installing DIMMs 37
- Removing hard drive blanks 39
- Multibay device options 41
- Expansion board options 44
- P400i Controller 48
- Cabling 61
- Cabling 62 62
- Battery pack cabling 63
- Multibay backplane cabling 64
- Configuration and utilities 65
- HP ROM-Based Setup Utility 66
- Array Configuration Utility 67
- Management tools 69
- Erase Utility 70
- Management Agents 70
- HP Systems Insight Manager 70
- Redundant ROM support 70
- USB support 71
- Diagnostic tools 72
- HP Insight Diagnostics 73
- Integrated Management Log 73
- Keeping the system current 74
- Care Pack 75
- Troubleshooting 76
- Symbols on equipment 77
- Warnings and cautions 77
- Symptom information 78
- Loose connections 79
- Service notifications 79
- Troubleshooting flowcharts 80
- General diagnosis flowchart 81
- Symptoms: 83
- Troubleshooting 85 85
- POST problems flowchart 86
- OS boot problems flowchart 87
- Troubleshooting 89 89
- Possible causes: 90
- Redundancy failure 90
- Troubleshooting 91 91
- Battery replacement 92
- FCC rating label 93
- FCC logo, United States only 94
- Modifications 95
- Japanese notice 96
- BSMI notice 96
- Korean notice 97
- Laser compliance 97
- Battery replacement notice 97
- Electrostatic discharge 99
- Specifications 100
- Technical support 102
- Technical support 103 103
- Customer Self Repair 104
- Reparo feito pelo cliente 106
- Technical support 107 107
- Technical support 108 108
- Technical support 109 109
- Acronyms and abbreviations 110
- Index 114 114
- Index 115 115
- Index 116 116
Relacionado con productos y manuales para Hardware De La Computadora Hp ProLiant DL365 Server
(107 paginas)
(187 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales