HP EliteDesk 705 G2 Base Model Small Form Factor PC Manual de usuario Pagina 117
- Pagina / 153
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Control panel message Description Recommended action
RTC (real-time clock) battery may need to
be replaced.
problem persists, replace the RTC battery. See
the Removal and Replacement section for
instructions on installing a new battery.
008–Microcode Patch Error Processor is not supported by the BIOS. 1. Upgrade BIOS to proper version.
2. Change the processor.
009–PMM Allocation Error during MEBx
Download
Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM.
1. Reboot the computer.
2. Unplug the power cord, re-seat the
memory modules, and reboot the
computer.
3. If the memory conguration was recently
changed, unplug the computer, restore
the original memory conguration, and
reboot the computer.
4. If the error persists, replace the system
board.
100-Front Audio Not Connected Front audio cable has been detached or
unseated from system board.
Reconnect or replace front audio cable.
00A-Product Information Not Valid The product information programmed into the
system board is missing or invalid.
Use Computer Setup to update this information.
00B-MEBx Module did not checksum correctly Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM.
1. Reboot the computer.
2. Unplug the power cord, re-seat the
memory modules, and reboot the
computer.
3. If the memory conguration was recently
changed, unplug the power cord, restore
the original memory conguration, and
reboot the computer.
4. If the error persists, replace the system
board.
00C-PMM Deallocation Error during MEBx
Cleanup
Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM.
1. Reboot the computer.
2. Unplug the power cord, re-seat the
memory modules, and reboot the
computer.
3. If the memory conguration was recently
changed, unplug the power cord, restore
the original memory conguration, and
reboot the computer.
4. If the error persists, replace the system
board.
00D-Setup Error during MEBx Execution MEBx selection or exit resulted in a setup
failure.
1. Reboot the computer.
2. Unplug the power cord, re-seat the
memory modules, and reboot the
computer.
3. If the memory conguration was recently
changed, unplug the power cord, restore
the original memory conguration, and
reboot the computer.
POST numeric codes and text messages 107
- Maintenance and Service Guide 1
- Safety warning notice 3
- Table of contents 5
- 1 Product features 11
- Front panel components 12
- Rear panel components 13
- Serial number location 14
- 2 Illustrated parts catalog 15
- Misc parts 17
- Generating static 21
- Grounding the work area 22
- Operating guidelines 23
- Routine care 24
- Service considerations 25
- Cables and connectors 26
- Hard Drives 26
- Lithium coin cell battery 26
- SATA hard drives 27
- SATA hard drive cables 27
- SMART ATA drives 27
- Cable management 28
- Preparation for disassembly 29
- Access panel 30
- Front bezel 30
- Front bezel security 31
- DDR3/DDR3L-SDRAM DIMMs 33
- Populating DIMM sockets 33
- Installing DIMMs 34
- Expansion card 36
- System board connections 41
- Drive positions 42
- Drives 37 47
- Drive power cable 56
- Small bae 57
- Fan bae 58
- Hood lock 59
- Front I/O assembly 61
- Power switch 63
- Fan sink 65
- Processor 66
- Power supply 68
- System board 70
- System board callouts 71
- Computer Setup–Main 75
- Computer Setup—Security 77
- Computer Setup—Advanced 79
- Safety and comfort 84
- Helpful hints 85
- Solving general problems 86
- Solving general problems 77 87
- Solving general problems 79 89
- Solving power problems 90
- Solving hard drive problems 91
- Solving display problems 94
- Solving display problems 85 95
- Solving display problems 87 97
- Solving audio problems 99
- Solving printer problems 101
- Solving Network Problems 105
- Solving Network Problems 97 107
- Solving memory problems 108
- Solving memory problems 99 109
- Solving software problems 115
- Resetting the password jumper 123
- 9 HP PC Hardware Diagnostics 127
- 10 System backup and recovery 129
- Using Windows tools 131
- Restore and recovery 131
- Windows 8 133
- Creating recovery media 136
- Backing up your information 138
- System Restore 139
- System Recovery 139
- A Battery replacement 143
- B Power Cord Set Requirements 146
- Country-Specic Requirements 147
- C Statement of Volatility 148
- D Specications 150
Relacionado con productos y manuales para No HP EliteDesk 705 G2 Base Model Small Form Factor PC
No HP ENVY 5534 e-All-in-One Printer Manual de usuario
(110 paginas)
(110 paginas)
No HP RP7 Retail System Model 7100 Manual de usuario
(24 paginas)
(24 paginas)
No HP Compaq tc1100 Tablet PC Manual de usuario
(61 paginas)
(61 paginas)
No HP 17bII+ Financial Calculator Manual de usuario
(310 paginas)
(310 paginas)
No HP Pro Slate 10 EE G1 Tablet Manual de usuario
(80 paginas)
(80 paginas)
No HP 33s Scientific Calculator Manual de usuario
(408 paginas)
(408 paginas)
No HP Omni 220-1130kr Desktop PC Manual de usuario
(52 paginas)
(52 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales