Hp ProLiant DL120 G7 Server Manual de usuario Pagina 38
- Pagina / 105
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Hardware options installation 38
6.
Install the storage controller.
7. Connect the storage controller cable to the controller and to the drive backplane.
See the server installation sheet and the documentation that ships with the storage controller.
IMPORTANT: The server does not power up if the PCI riser board assembly is not seated
properly.
8. Install the PCIe riser cage (on page 19).
9. Install the access panel (on page 18).
10. Install the server into the rack ("Installing the server into the rack" on page 25).
11. Power up the server ("Powering up and configuring the server" on page 26, on page 17).
BBWC module and battery pack option
CAUTION: To prevent a server malfunction or damage to the equipment, do not add or remove
the battery pack while an array capacity expansion, RAID level migration, or stripe size migration
is in progress.
CAUTION: After the server is powered down, wait 15 seconds and then check the amber LED
before unplugging the cable from the cache module. If the amber LED blinks after 15 seconds, do
not remove the cable from the cache module. The cache module is backing up data, and data is
lost if the cable is detached.
IMPORTANT: The battery pack might have a low charge when installed. In this case, a POST
error message is displayed when the server is powered up, indicating that the battery pack is
temporarily disabled. No action is necessary on your part. The internal circuitry automatically
recharges the batteries and enables the battery pack. This process might take up to four hours.
During this time, the cache module functions properly, but without the performance advantage of
the battery pack.
NOTE: The data protection and the time limit also apply if a power outage occurs. When power
is restored to the system, an initialization process writes the preserved data to the hard drives.
To install the component:
1. Power down the server (on page 17).
2. Remove the server from the rack (on page 17).
3. Remove the access panel (on page 18).
4. Remove the PCIe riser cage (on page 18).
5. Install the storage controller, if not installed ("Storage controller option" on page 37).
- HP ProLiant DL120 G7 Server 1
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs 8
- Rear panel components 8
- Rear panel LEDs 9
- System board components 10
- System maintenance switch 11
- System board LEDs 11
- NMI functionality 12
- DIMM slot locations 12
- SAS and SATA drive LEDs 13
- BBWC module LEDs 14
- Fan locations 15
- T-10/T15 Torx screwdriver 16
- Operations 17
- Remove the access panel 18
- Install the access panel 18
- Remove the PCIe riser cage 18
- Install the PCIe riser cage 19
- Remove the air baffle 19
- Install the air baffle 20
- Operations 21 21
- Rack planning resources 22
- Optimum environment 22
- Temperature requirements 23
- Rack warnings 24
- Installing hardware options 25
- Setup 26 26
- Registering the server 27
- Introduction 28
- Memory options 28
- DIMM identification 29
- Memory configuration 30
- Installing a DIMM 30
- Drive options 31
- Removing a drive 32
- Optical drive option 33
- Expansion board option 36
- Storage controller option 37
- Remove the rear bracket 41
- Remove the ATX power supply 41
- Cabling 48
- Internal USB cabling 49
- BBWC battery cabling 50
- Optical drive cabling 51
- SATA cabling 51
- SAS cabling 52
- • SFF model 53
- Configuration and utilities 54
- Using RBSU 55
- Auto-configuration process 55
- Array Configuration Utility 56
- • Selecting the boot volume 57
- Management tools 58
- Diagnostic tools 59
- Integrated Management Log 60
- Keeping the system current 61
- ProLiant Support Packs 62
- Firmware 62
- HP Smart Update Manager 62
- Care Pack 63
- Troubleshooting 64
- Warnings and cautions 65
- Symptom information 66
- Loose connections 68
- Service notifications 68
- Server health LEDs 68
- Troubleshooting flowcharts 69
- General diagnosis flowchart 70
- Symptoms: 72
- Troubleshooting 74 74
- POST problems flowchart 75
- OS boot problems flowchart 77
- Troubleshooting 78 78
- • Redundancy failure 79
- (http://www.hp.com/support) 80
- Troubleshooting 81 81
- Battery 82
- FCC rating label 83
- Japanese class A notice 85
- BSMI notice 86
- Korean class A notice 86
- Chinese notice 86
- Laser compliance 86
- Battery replacement notice 87
- Electrostatic discharge 88
- Specifications 89
- Specification Value 90
- Support and other resources 91
- Customer Self Repair 93
- Reparo feito pelo cliente 95
- Acronyms and abbreviations 99
- Version Control Agent 101
- Documentation feedback 102
- Index 103 103
- Index 104 104
- Index 105 105
Relacionado con productos y manuales para Hardware De La Computadora Hp ProLiant DL120 G7 Server
Hardware De La Computadora Hp Server Management Packs for Microsoft System Cente Manual de usuario
(86 paginas)
(86 paginas)
Hardware De La Computadora Hp Планшетный ПК HP EliteBook Revolve 810 G1 Manual de usuario
(113 paginas)
(113 paginas)
(88 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales