Hp ProLiant DL388e Gen8 Server Manual de usuario Pagina 46
- Pagina / 136
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Hardware options installation 46
8.
Connect the common end of the Mini-SAS Y-cable to the controller option.
9. Install the PCI riser cage ("Install the PCI riser cages" on page 25).
10. Route the split ends of the Mini-SAS Y-cable along the side of the system board towards the front chassis,
and then connect the cable to the drive backplane.
The Mini-SAS cable routing from the secondary PCI riser cage is only supported in the 8+8 SFF drive
configuration.
11. Connect the rest of the drive cables required in this drive configuration. For more information, see
"Storage cabling (on page 81)."
12. Install the PCI riser cage ("Install the PCI riser cages" on page 25).
13. If you intend to use an FBWC module and capacitor pack, install these options now ("Installing the
FBWC module and capacitor pack" on page 49).
14. Install the air baffle (on page 23).
15. Install the access panel (on page 23).
16. Install the server into the rack ("Installing the server into the rack" on page 32).
17. Power up the server (on page 19).
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
18. Install the drives ("Installing a hot-plug drive" on page 36).
Mini-SAS Y-cable options
The Mini-SAS Y-cables in these option kits support the following drive configurations.
Drive configuration Mini-SAS Y-cable required
8 LFF
690 mm
8 SFF
540 mm
8+8 SFF*
540 mm and 780 mm
*
This drive configuration requires the installation of two HP Smart Array P430 controller boards in the full-height side of
the primary PCI riser cage.
To connect the cable option:
1. Power down the server (on page 19).
2. Remove all power:
a. Disconnect each power cord from the power source.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Rear panel components 9
- Rear panel LEDs and buttons 11
- System board components 12
- Item Description 13
- DIMM slot locations 14
- System maintenance switch 14
- NMI functionality 14
- Drive numbering 15
- Drive LED definitions 16
- FBWC module LED definitions 16
- Fan locations 18
- Operations 19
- Remove the access panel 22
- Install the access panel 23
- Remove the air baffle 23
- Install the air baffle 23
- Remove the PCI riser cages 24
- Install the PCI riser cages 25
- Optimum environment 27
- Temperature requirements 28
- Power requirements 29
- Server warnings and cautions 30
- Rack warnings 31
- Installing hardware options 32
- Registering the server 34
- Introduction 35
- Security bezel option 35
- Drive options 35
- Installing a hot-plug drive 36
- Rear drive cage options 37
- Drive cable options 44
- Mini-SAS cable option 45
- Mini-SAS Y-cable options 46
- Controller options 47
- Optical drive option 52
- Hot-plug fan module option 53
- • In a redundant fan mode: 54
- Memory options 58
- HP SmartMemory 59
- DIMM identification 60
- Memory protection modes 61
- Memory population guidelines 62
- Installing a DIMM 64
- Processor option 65
- Expansion board options 70
- GPU power cable option 72
- Cabling 81
- 4 SFF SATA cabling 82
- 6 LFF SATA cabling 82
- 6 SFF SATA cabling 83
- 8 LFF cabling 83
- 8 SFF cabling 85
- 8+8 SFF cabling 87
- 2 LFF rear drive cabling 90
- 2 SFF rear drive cabling 91
- Capacitor pack cabling 92
- Cabling 93 93
- Optical drive cabling 94
- GPU power cabling 94
- Dual-rank GPU 95
- Primary GPU power cabling 95
- Secondary GPU power cabling 96
- Server mode 97
- HP product QuickSpecs 97
- HP iLO Management 97
- Active Health System 98
- Intelligent Provisioning 99
- HP Insight Diagnostics 100
- Erase Utility 100
- HP Insight Online 101
- HP Service Pack for ProLiant 102
- HP ROM-Based Setup Utility 102
- Using RBSU 103
- Auto-configuration process 103
- Configuring AMP modes 104
- Boot options 104
- Utilities and features 105
- ROMPaq utility 106
- Automatic Server Recovery 106
- USB support 106
- Redundant ROM support 106
- Keeping the system current 107
- ProLiant servers 108
- Troubleshooting 109
- System battery replacement 110
- Regulatory information 112
- Electrostatic discharge 113
- Specifications 114
- Specification Value 116
- Support and other resources 120
- Customer Self Repair 122
- Reparo feito pelo cliente 124
- Acronyms and abbreviations 128
- Documentation feedback 132
- Index 133 133
- Index 134 134
- Index 135 135
- Index 136 136
Relacionado con productos y manuales para Hardware De La Computadora Hp ProLiant DL388e Gen8 Server
(86 paginas)
(93 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales