Hp ProLiant ML370 G5 Server Manual de usuario Pagina 59
- Pagina / 135
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Hardware options installation 59
14.
Install the access panel (on page 26).
15. Do one of the following:
o Close or install the tower bezel, as needed.
o Slide the server back into the rack.
16. Power up the server (on page 20).
Redundant hot-plug fans option
The server supports redundant hot-plug fans to provide proper airflow to the system if a primary fan fails.
In the standard, non-redundant, configuration, fans 1, 2, and 3 cool the server.
For the redundant configuration, fans 4, 5, and 6 are added to back up the primary fans. This
configuration enables the server to continue operation in non-redundant mode, if a fan failure occurs. The
following rules apply:
• If one fan fails in non-redundant mode, the server shuts down.
• If one fan fails in redundant mode, the server converts to non-redundant mode.
• If two fans fail in redundant mode, the server shuts down.
WARNING: To prevent personal injury from hazardous energy:
• Remove watches, rings, or other metal objects.
• Use tools with insulated handles.
• Do not place tools or metal parts on top of batteries.
To install the fans:
1. Do one of the following:
o Open or remove the tower bezel, as needed ("Open or remove the tower bezel" on page 21).
o Extend the server from the rack (on page 22).
2. Remove the access panel. ("Remove the access panel" on page 25)
3. Install three hot-plug fans into the center wall.
- User Guide 1
- Audience assumptions 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Item Description Status 9
- Systems Insight Display LEDs 10
- Rear panel components 11
- Rear panel LEDs 12
- System board components 13
- System maintenance switch 14
- SAS and SATA device numbers 15
- SAS and SATA hard drive LEDs 16
- Online/activity 17
- LED (green) 17
- Fault/UID LED 17
- (amber/blue) 17
- Interpretation 17
- FBDIMM slots 18
- Power supply backplane LED 19
- Fan locations 19
- Operations 20
- Operations 21 21
- Operations 22 22
- Remove the rack bezel 23
- Operations 24 24
- Install the rack bezel 25
- Remove the access panel 25
- Install the access panel 26
- Remove the center wall 27
- Rack planning resources 28
- Optimum environment 29
- Temperature requirements 30
- Power requirements 30
- Rack warnings 31
- Server warnings and cautions 31
- Setup 32 32
- Installing hardware options 33
- Setting up a tower server 33
- Setup 34 34
- Registering the server 35
- Introduction 36
- Processor option 36
- 13. Install the heatsink 41
- 15. Install the PPM 41
- Memory options 42
- Advanced ECC memory 43
- Online spare memory 44
- Mirrored memory 45
- Memory boards and FBDIMMs 46
- Removing FBDIMMs 48
- Installing FBDIMMs 49
- Hot-plug hard drive options 50
- Remove the hard drive blank 51
- Prepare the hard drive 51
- Expansion board options 61
- Performance balancing 62
- Expansion slot cover 62
- Installing expansion boards 63
- Removing expansion boards 64
- • Rack rails 67
- • Cable management arm 67
- • Server rails 67
- • Rack bezel 67
- Remove the CD-ROM drive 69
- Install the center wall 74
- Cabling 75
- SAS cabling 76
- CD-ROM drive cabling 77
- Video cabling 78
- Parallel/serial port cabling 78
- Diskette drive cabling 79
- BBWC option cabling 79
- Internal USB connector 80
- Configuration and utilities 81
- HP ROM-Based Setup Utility 82
- Boot options 83
- BIOS Serial Console 83
- Configuring mirrored memory 83
- Array Configuration Utility 84
- Auto-configuration process 84
- Management tools 86
- Management Agents 88
- HP Systems Insight Manager 88
- Redundant ROM support 88
- USB support 89
- Diagnostic tools 90
- Integrated Management Log 91
- Keeping the system current 92
- Care Pack 93
- Battery replacement 94
- Battery replacement 95 95
- Troubleshooting 96
- Symbols on equipment 97
- Warnings and cautions 97
- Symptom information 98
- Loose connections 99
- Service notifications 100
- Troubleshooting flowcharts 100
- General diagnosis flowchart 101
- Symptoms: 103
- Troubleshooting 105 105
- POST problems flowchart 106
- OS boot problems flowchart 107
- • Redundancy failure 110
- Troubleshooting 111 111
- Electrostatic discharge 112
- FCC rating label 113
- Class A equipment 113
- Class B equipment 113
- Modifications 114
- • EMC Directive 2004/108/EC 115
- Japanese notice 116
- BSMI notice 116
- Korean notice 117
- Laser compliance 117
- Battery replacement notice 117
- Specifications 119
- Specification Value 120
- Technical support 121
- Customer Self Repair 122
- Technical support 124 124
- Reparo feito pelo cliente 126
- Technical support 127 127
- Technical support 128 128
- Acronyms and abbreviations 129
- Index 132 132
- Index 133 133
- Index 134 134
- Index 135 135
Relacionado con productos y manuales para Hardware De La Computadora Hp ProLiant ML370 G5 Server
(78 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales