HP RP7 Retail System Model 7100 Manual de usuario Pagina 239
- Pagina / 244
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming Reference Guide
231
Appendix F
Quick Setup
Use the barcodes in this appendix to perform quick setup procedures for common tasks.
Scan the following barcode to set the scanner
back to the factory defaults:
Scan the following barcode (USB HID Keyboard Emulation) in order to put the HP RPOS
Integrated Scanner into the default mode.
When the scanner is changed between HID and USB-COM mode, allow the Windows
operat
ing system a little time to reload the native drivers for the scanner.
OPOS Driver
The HP RPOS Integrated Scanner by default is shipped in the human interface device (HID)
keyboard emulation mode. In order to use the barcode scanner with OLE for Retail POS
(OPOS) drivers the scanner must be put into USB COM (OPOS) mode.
For your convenience the barcode to put the HP RPOS Integrated Scanner into USB COM
(OPOS) mod
e or into HID keyboard emulation are located in this document.
Scan the following barcode (USB COM OPOS) to put
the HP RPOS Integrated Scanner into
the mode to be used with the OPOS drivers.
Scanning the "Set All Defaults" barcode does not change the interface type.
Restore Custom Default Configuration
$P,HA00,P(CR)
USB HID Keyboard Emulation
USB COM (OPOS)
- Programming Reference Guide 1
- Table of Contents 3
- Contents 4
- Chapter 1 9
- Introduction 9
- References 10
- Technical Support 10
- About the Scanner 11
- Programming the Scanner 11
- Chapter 2 13
- Interface Selection 14
- Configure Interface Settings 15
- Global Interface Features 15
- Configuring Other Features 15
- Software Version Transmission 15
- Restore Custom Defaults 16
- Chapter 3 17
- Configuration Using Barcodes 17
- Enter/Exit Programming Mode 18
- To program features: 18
- GLOBAL INTERFACE FEATURES 19
- USB-COM INTERFACES 21
- Intercharacter Delay 22
- Beep On ASCII BEL 23
- Beep Upon Not on File 23
- ACK NAK Error Handling 27
- Indicate Transmission Failure 27
- USB KEYBOARD SETTINGS 29
- Country Mode 30
- Country Mode (continued) 31
- Send Control Characters 33
- Intercode Delay 34
- Caps Lock State 34
- USB Keyboard Speed 35
- USB Keyboard Numeric Keypad 36
- DATA FORMAT 37
- Global Prefix/Suffix 38
- 31 39
- 33 41
- 35 43
- − 1D Symbologies 43
- 37 45
- Data Format 47
- 39 47
- − 2D Symbologies 47
- Case Conversion 48
- READING PARAMETERS 49
- Double Read Timeout 50
- 43 51
- LED AND BEEPER INDICATORS 52
- Good Read Beep Type 53
- Good Read Beep Frequency 53
- Good Read Beep Length 54
- Good Read Beep Volume 55
- Good Read LED Duration 56
- SCANNING FEATURES 57
- Green Spot Duration 58
- Mobile Phone Mode 58
- Mobile Bias 59
- Illumination Off Time 59
- Illumination On Time 60
- Aiming Pointer 61
- Aiming Duration Timer 61
- Decode Negative Image 62
- Image Capture 62
- MULTIPLE LABEL READING 63
- 1D SYMBOLOGIES 65
- DISABLE ALL SYMBOLOGIES 66
- CODE EAN/UPC 67
- UPC-A Enable/Disable 68
- Expand UPC-A to EAN-13 69
- UPC-A 2D Component 70
- UPC-E Enable/Disable 70
- UPC-E 2D Component 71
- Expand UPC-E to EAN-13 72
- Expand UPC-E to UPC-A 72
- GTIN FORMATTING 73
- EAN 13 (JAN 13) 74
- EAN-13 Flag 1 Character 75
- EAN-13 ISBN Conversion 75
- EAN-13 2D Component 76
- ISSN Enable/Disable 76
- EAN 8 (JAN 8) 77
- Expand EAN 8 to EAN 13 78
- EAN 8 2D Component 78
- UPC/EAN GLOBAL SETTINGS 79
- UPC/EAN Quiet Zones 80
- Optional Add-ons 81
- Optional Add-On Timer 82
- 75 83
- Optional GS1-128 Add-On Timer 85
- 79 87
- Code 39 Enable/Disable 88
- 81 89
- Code 39 Full ASCII 90
- Code 39 Quiet Zones 91
- Code 39 Length Control 91
- Code 39 Set Length 1 92
- Code 39 Set Length 2 93
- Code 32 Enable/Disable 94
- Code 39 CIP Enable/Disable 95
- CODE 39 LAPOSTE 96
- CODE 128 96
- Expand Code 128 to Code 39 97
- Code 128 Quiet Zones 99
- Code 128 Length Control 99
- Code 128 Set Length 1 100
- Code 128 Set Length 2 101
- GS1-128 Enable 102
- GS1-128 2D Component 102
- CODE ISBT 128 103
- ISBT 128 Concatenation Mode 104
- 97 105
- INTERLEAVED 2 OF 5 (I 2 OF 5) 106
- 99 107
- I 2 of 5 Length Control 108
- I 2 of 5 Set Length 1 109
- I 2 of 5 Set Length 2 110
- FOLLETT 2 OF 5 111
- STANDARD 2 OF 5 112
- 105 113
- Standard 2 of 5 Set Length 1 114
- Standard 2 of 5 Set Length 2 115
- INDUSTRIAL 2 OF 5 116
- 109 117
- 111 119
- CODE IATA 120
- Codabar Enable/Disable 121
- 115 123
- Codabar Quiet Zones 124
- Codabar Length Control 124
- Codabar Set Length 1 125
- Codabar Set Length 2 126
- ABC CODABAR 127
- Concatenation Mode 128
- 121 129
- Code 11 Enable/Disable 130
- Code 11 Length Control 131
- Code 11 Set Length 1 132
- Code 11 Set Length 2 133
- GS1 DATABAR™ OMNIDIRECTIONAL 134
- GS1 DATABAR™ EXPANDED 135
- 129 137
- 131 139
- GS1 DATABAR™ LIMITED 140
- Code 93 Enable/Disable 141
- Enable Check C 142
- Code 93 Length Control 143
- Code 93 Set Length 1 144
- Code 93 Set Length 2 145
- Code 93 Quiet Zones 146
- MSI Enable/Disable 146
- 139 147
- MSI Length Control 148
- MSI Set Length 1 149
- MSI Set Length 2 150
- Plessey Enable/Disable 151
- Plessey Length Control 152
- Plessey Set Length 1 153
- Plessey Set Length 2 154
- 2D SYMBOLOGIES 155
- 2D Maximum Decoding Time 156
- 2D Structured Append 157
- Aztec Code 158
- Aztec Code Set Length 1 159
- Aztec Code Set Length 2 160
- China Sensible Code 161
- 155 163
- Data Matrix 164
- Data Matrix Length Control 165
- Data Matrix Set Length 2 166
- Maxicode 167
- Maxicode Length Control 168
- Maxicode Set Length 2 169
- PDF417 Enable / Disable 170
- PDF417 Length Control 170
- PDF417 Set Length 1 171
- PDF417 Set Length 2 172
- Micro PDF417 173
- Micro PDF417 Length Control 174
- Micro PDF417 Set Length 2 175
- QR Code Enable / Disable 176
- QR Code Length Control 176
- Set Length 1 177
- Set Length 2 178
- Micro QR Code 179
- UCC Composite 182
- UCC Optional Composite Timer 183
- Postal Code Selection 184
- Postnet BB Control 185
- 2D Symbologies 186
- Chapter 4 187
- USB-COM Parameters 188
- ACK NAK Options 189
- ACK Character 189
- NAK Character 190
- ACK NAK Timeout Value 191
- ACK NAK Retry Count 192
- Disable Character 193
- Enable Character 194
- USB Keyboard Interface 195
- Symbologies 196
- Data Editing 197
- 00 - 20 Characters (ASCII) 198
- Global AIM ID 199
- Label ID 200
- 193 201
- 195 203
- Character Conversion 205
- Reading Parameters 206
- Scanning Features 207
- Aiming Duration Time 208
- 201 209
- Appendix A 211
- Technical Specifications 211
- 205 213
- LED and Beeper Indications 215
- Error Codes 216
- Appendix B 217
- Standard Defaults 217
- 211 219
- 213 221
- 215 223
- 217 225
- Appendix C 227
- Sample Barcodes 227
- Sample Barcodes — continued 228
- GS1 DataBar™ (RSS) 229
- GS1 DataBar™-14 229
- 2D Barcodes 230
- Appendix D 231
- Appendix E 233
- Scancode Tables 233
- Interface Type USB-Keyboard 234
- Appendix F 239
- Quick Setup 239
- Carriage Return 240
- 233 241
- $P,HA00,P(CR) 242
- ASCII Chart 243
Relacionado con productos y manuales para Lectores De Códigos De Barras HP RP7 Retail System Model 7100
(156 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.153 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales