HP ProDesk 600 G4 Base Model Small Form Factor PC Manual de usuario Pagina 34
- Pagina / 124
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CAUTION: Never remove a wide, level key (like the space bar) from the keyboard. If these keys are
improperly removed or installed, the keyboard may not function properly.
● Cleaning under a key may be done with a swab moistened with isopropyl alcohol and then squeezed out.
Be careful not to wipe away lubricants necessary for proper key functions. Use tweezers to remove any
bers or dirt in conned areas. Allow the parts to air dry before reassembly.
Cleaning the monitor
● Wipe the monitor screen with a towelette designed for cleaning monitors or with a clean cloth moistened
with water. Do not use sprays or aerosols directly on the screen; the liquid may seep into the housing and
damage a component. Never use solvents or
ammable liquids on the monitor.
● To clean the monitor body follow the procedures in Cleaning the computer case on page 25.
Cleaning the mouse
Before cleaning the mouse, ensure that the power to the computer is turned o.
● Clean the mouse ball by rst removing the retaining plate and the ball from the housing. Pull out any debris
from the ball socket and wipe the ball with a clean, dry cloth before reassembly.
● To clean the mouse body, follow the procedures in Cleaning the computer case on page 25.
Service considerations
Listed below are some of the considerations that you should keep in mind during the disassembly and assembly
of the computer.
Tools and software requirements
To service the computer, you need the following:
● Torx-15 screwdriver
● 3/16-in. socket driver
● Flat-bladed screwdriver (may sometimes be used in place of the Torx screwdriver)
● Phillips #2 screwdriver
● Diagnostics software
Screws
The screws used in the computer are not interchangeable. They may have standard or metric threads and may
be of dierent lengths. If an incorrect screw is used during the reassembly process, it can damage the unit. HP
strongly recommends that all screws removed during disassembly be kept with the part that was removed, then
returned to their proper locations.
CAUTION: Metric screws have a black nish. U.S. screws have a silver nish and are used on hard drives only.
CAUTION: As each subassembly is removed from the computer, it should be placed away from the work area to
prevent damage.
26 Chapter 3 Routine care, SATA drive guidelines, and disassembly preparation
- Maintenance and Service Guide 1
- About This Book 3
- Table of contents 5
- 1 Product features 9
- Front panel components 10
- Rear panel components 11
- 2 Illustrated parts catalog 12
- Computer major components 5 13
- Miscellaneous parts 14
- Miscellaneous parts 7 15
- Miscellaneous parts 9 17
- Miscellaneous parts 11 19
- Miscellaneous parts 13 21
- Miscellaneous parts 15 23
- Miscellaneous parts 17 25
- Miscellaneous parts 19 27
- Miscellaneous parts 21 29
- Generating static 30
- Grounding the work area 31
- Operating guidelines 32
- Routine care 33
- Service considerations 34
- SMART ATA drives 35
- Preparation for disassembly 36
- Access panel 37
- Optical drive 38
- Front bezel 39
- Hard drives 40
- Drive cage 42
- Memory module 43
- Power supply 45
- Fan shroud 46
- Fan-sink 47
- Processor 48
- Serial connector module 50
- System board 51
- 6. Remove the lower cage (2) 52
- System board 45 53
- Connector board 54
- Computer Setup–Main 57
- Computer Setup—Security 59
- Computer Setup—Advanced 61
- Safety and comfort 67
- Helpful hints 68
- Solving general problems 69
- Solving general problems 63 71
- Solving power problems 72
- Solving hard drive problems 73
- Solving display problems 76
- Solving display problems 69 77
- Solving display problems 71 79
- Solving audio problems 80
- Solving audio problems 73 81
- Solving printer problems 82
- Solving network problems 86
- Solving network problems 79 87
- Solving memory problems 89
- Solving software problems 92
- 10 System backup and recovery 106
- Using Windows tools 108
- Restore and recovery 108
- A Battery replacement 111
- Current BIOS steps 114
- Nonvolatile memory usage 116
- Nonvolatile memory usage 109 117
- Questions and answers 118
- Using HP Sure Start 119
- C Power cord set requirements 120
- Country-specic requirements 121
- D Specications 122
Relacionado con productos y manuales para No HP ProDesk 600 G4 Base Model Small Form Factor PC
No HP AMP 130 Printer Manual de usuario
(132 paginas)
(132 paginas)
(84 paginas)
(89 paginas)
No HP ProDesk 400 G3 Microtower PC Manual de usuario
(48 paginas)
(48 paginas)
(48 paginas)
(40 paginas)
No HP Ink Tank 310 Manual de usuario
(99 paginas)
(99 paginas)
No HP EliteDesk 800 G4 Tower PC Manual de usuario
(76 paginas)
(76 paginas)
No HP Tango Manual de usuario
(106 paginas)
(106 paginas)
No HP OMEN - 15-dc0086nr Manual de usuario
(80 paginas)
(69 paginas)
No HP ZBook 17 G2 Mobile Workstation Manual de usuario
(126 paginas)
No HP ENVY 5534 e-All-in-One Printer Manual de usuario
(110 paginas)
(110 paginas)
No HP OMEN Keyboard 1100 Manual de usuario
(11 paginas)
(11 paginas)
(70 paginas)
No HP ENVY 5010 All-in-One Printer Manual de usuario
(109 paginas)
(109 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.137 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales