HP ProDesk 600 G4 Base Model Small Form Factor PC Manual de usuario Pagina 62
- Pagina / 124
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 5-3 Computer Setup—Advanced (for advanced users) (continued)
Option Heading
UEFI boot sources always have precedence over legacy boot sources.
● Legacy Boot Order
Specify the order in which legacy boot sources (such as a network interface card, internal hard drive,
USB optical drive, or internal optical drive) are checked for a bootable operating system image.
Specify the order of attached hard drives. The rst hard drive in the order will have priority in the boot
sequence and will be recognized as drive C (if any devices are attached).
NOTE: To drag a device to a preferred place, press Enter.
NOTE: MS-DOS drive lettering assignments may not apply after a non-MS-DOS operating system has
started.
Shortcut to Temporarily Override Boot Order
To boot one time from a device other than the default device specied in Boot Order, restart the computer
and press Esc (to access the Startup menu) and then F9 (Boot Menu), or only F9 (skipping the Startup menu)
when the monitor light turns green. After POST is completed, a list of bootable devices is displayed. Use
the arrow keys to select the preferred bootable device and press Enter. The computer then boots from
the selected non-default device for this one time.
Secure Boot Conguration Congure Legacy Support and Secure Boot
Legacy Support – Lets you turn o all legacy support on the computer, including booting to DOS, running
legacy graphics cards, booting to legacy devices, and so on.
Secure Boot – Lets you make sure an operating system is legitimate before booting to it, making Windows
resistant to malicious modication from preboot to full OS booting, preventing rmware attacks. UEFI and
Windows Secure Boot only allow code signed by pre-approved digital certicates to run during the rmware
and OS boot process.
Default is ‘Legacy Support Enable and Secure Boot Disable’ for non-Windows congurations. Default is
‘Legacy Support Disable and Secure Boot Enable’ for Windows 10 congurations.
Secure Boot Key Management
Lets you manage the custom key settings.
Clear Secure Boot Keys
Lets you delete any previously loaded custom boot keys. Clearing keys will disable secure boot. Default is
disabled.
Reset Secure Boot keys to factory defaults
Default is disabled.
Enable MS UEFI CA key
Disabling this setting alters the Secure Boot key list to further restrict the allowed software components. Set
this option to ‘disable’ to support Device Guard.
System Options Congure Storage Controller for RAID (enable/disable)
Lets you enable onboard RAID. Default is disabled.
POST Prompt for RAID Conguration (Intel only)
When disabled, the prompt for ‘RAID option ROM’ in legacy mode is suppressed.
SVM CPU Virtualization (AMD only)
Controls the virtualization features of the processor. Changing this setting requires turning the computer o
and then back on. Default is disabled.
Virtualization Technology (VTx) (Intel only)
54 Chapter 5 Computer Setup (F10) Utility
- Maintenance and Service Guide 1
- About This Book 3
- Table of contents 5
- 1 Product features 9
- Front panel components 10
- Rear panel components 11
- 2 Illustrated parts catalog 12
- Computer major components 5 13
- Miscellaneous parts 14
- Miscellaneous parts 7 15
- Miscellaneous parts 9 17
- Miscellaneous parts 11 19
- Miscellaneous parts 13 21
- Miscellaneous parts 15 23
- Miscellaneous parts 17 25
- Miscellaneous parts 19 27
- Miscellaneous parts 21 29
- Generating static 30
- Grounding the work area 31
- Operating guidelines 32
- Routine care 33
- Service considerations 34
- SMART ATA drives 35
- Preparation for disassembly 36
- Access panel 37
- Optical drive 38
- Front bezel 39
- Hard drives 40
- Drive cage 42
- Memory module 43
- Power supply 45
- Fan shroud 46
- Fan-sink 47
- Processor 48
- Serial connector module 50
- System board 51
- 6. Remove the lower cage (2) 52
- System board 45 53
- Connector board 54
- Computer Setup–Main 57
- Computer Setup—Security 59
- Computer Setup—Advanced 61
- Safety and comfort 67
- Helpful hints 68
- Solving general problems 69
- Solving general problems 63 71
- Solving power problems 72
- Solving hard drive problems 73
- Solving display problems 76
- Solving display problems 69 77
- Solving display problems 71 79
- Solving audio problems 80
- Solving audio problems 73 81
- Solving printer problems 82
- Solving network problems 86
- Solving network problems 79 87
- Solving memory problems 89
- Solving software problems 92
- 10 System backup and recovery 106
- Using Windows tools 108
- Restore and recovery 108
- A Battery replacement 111
- Current BIOS steps 114
- Nonvolatile memory usage 116
- Nonvolatile memory usage 109 117
- Questions and answers 118
- Using HP Sure Start 119
- C Power cord set requirements 120
- Country-specic requirements 121
- D Specications 122
Relacionado con productos y manuales para No HP ProDesk 600 G4 Base Model Small Form Factor PC
No HP AMP 130 Printer Manual de usuario
(132 paginas)
(132 paginas)
(84 paginas)
(89 paginas)
No HP ProDesk 400 G3 Microtower PC Manual de usuario
(48 paginas)
(48 paginas)
(48 paginas)
(40 paginas)
No HP Ink Tank 310 Manual de usuario
(99 paginas)
(99 paginas)
No HP EliteDesk 800 G4 Tower PC Manual de usuario
(76 paginas)
(76 paginas)
No HP Tango Manual de usuario
(106 paginas)
(106 paginas)
No HP OMEN - 15-dc0086nr Manual de usuario
(80 paginas)
(69 paginas)
No HP ZBook 17 G2 Mobile Workstation Manual de usuario
(126 paginas)
No HP ENVY 5534 e-All-in-One Printer Manual de usuario
(110 paginas)
(110 paginas)
No HP OMEN Keyboard 1100 Manual de usuario
(11 paginas)
(11 paginas)
(70 paginas)
No HP ENVY 5010 All-in-One Printer Manual de usuario
(109 paginas)
(109 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 1.171 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales