HP 8800 Router Series Manual de instalación Pagina 45
- Pagina / 121
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Diagnosing transceiver modules
The device provides the alarm function and digital diagnosis function for transceiver modules. When
a transceiver module fails or inappropriately work, you can check for alarms present on the
transceiver module to identify the fault source or examine the key parameters monitored by the digital
diagnosis function, including the temperature, voltage, laser bias current, TX power, and RX power.
To display alarm information or fault detection parameters for a transceiver module:
Task Command Remarks
Display the current alarm information of the
transceiver module in a specified interface
display transceiver alarm
interface [ interface-type
interface-number ]
Available for all
transceiver modules.
Display the currently measured values of the
detection parameters of the transceiver module
in a specified interface
display transceiver diagnosis
interface [ interface-type
interface-number ]
Available for all
transceiver modules.
# Display the alarm information of the transceiver module plugged in GigabitEthernet 3/1/1.
<Sysname> display transceiver alarm interface GigabitEthernet 3/1/1
GigabitEthernet3/1/1 transceiver current alarm information:
RX loss of signal
Table 17 Command output
Field Remarks
SFP
RX loss of signal Receive (RX) signal is lost.
TX fault TX fault.
RX power high RX power is high.
RX power low RX power is low.
TX power high TX power is high.
TX power low TX power is low.
TX bias high TX bias current is high.
TX bias low TX bias current is low.
Temp high Temperature is high.
Temp low Temperature is low.
Voltage high Voltage is high.
Voltage low Voltage is low.
Transceiver info I/O error Transceiver information read and write error.
Transceiver info checksum error Transceiver information checksum error.
Transceiver type and port configuration
mismatch
Transceiver type does not match port configuration.
Transceiver type not supported by port
hardware
Transceiver type is not supported on the port.
40
- HP A8800 Routers 1
- Contents 3
- Preparing for installation 6
- Installation tools 8
- Installing the router 10
- Grounding the router 16
- Installing the power system 17
- Installing a DC power supply 18
- Installing a card 19
- Installing an SPE subcard 20
- Connecting power cables 21
- Connecting DC power cables 22
- Verifying the installation 24
- Logging in to the router 25
- Powering on the router 31
- Configuration Guide 33
- Connecting an optical fiber 35
- Installing an FMT (optional) 36
- Hardware management 38
- Rebooting the router 39
- RX loss of signal 45
- Field Remarks 46
- Table 18 Command output 47
- Field Descri 47
- Troubleshooting 48
- Fan failure 49
- MPU failure 50
- LPU failure 51
- Interface failure 51
- Technical support 52
- Replacement procedures 53
- Replacing an AC power supply 54
- Replacing a card 56
- Replacing a subcard 58
- Replacing a fan tray 59
- Replacing a CF card 62
- <Sysname> umount cfa0: 63
- Hardware specifications 66
- Figure 45 A8805 front view 67
- A8808 chassis views 68
- Figure 47 A8808 front view 69
- Figure 48 A8808 rear view 70
- A8812 chassis views 71
- Figure 50 A8812 rear view 72
- Cooling system 73
- A8805 and A8812 airflow 74
- A8808 airflow 75
- Card specifications 76
- MPU specifications 78
- SPC card specifications 79
- SPE card specifications 79
- Subcard specifications 80
- OAA module specifications 81
- Power supply system 82
- Table 33 AC power supply LEDs 83
- LED Status Description 83
- Power supply LEDs 89
- Fan LEDs 89
- MPU LEDs 90
- SPC card LEDs 91
- LINK/ACT LED 92
- Combo interface LED 92
- LINK and ACT LEDs 92
- SPE card LED 93
- Subcard LEDs 93
- Transceiver modules 94
- Lightning protection 99
- Engineering labels 101
- Generic labels 102
- Labels for devices 103
- Filling in labels 103
- Affixing labels 103
- B02 03 12 104
- Affixing a generic label 105
- Guidelines 106
- Examples 106
- Cable management 113
- Cable management examples 114
- NOTE: 115
- Support and other resources 117
- Conventions 118
- Network topology icons 119
- Port numbering in examples 119
Relacionado con productos y manuales para Redes HP 8800 Router Series
Redes HP Cooktop 10GBE Manual de usuario
(34 paginas)
(34 paginas)
Redes HP -PB 10 Manual de usuario
(112 paginas)
(112 paginas)
Redes HP 3PAR Guía de usuario
(53 paginas)
(53 paginas)
Redes HP U522 Manual de usuario
(44 paginas)
(44 paginas)
Redes HP 9200c Manual de usuario
(218 paginas)
(218 paginas)
Redes HP 480-0005-00-15 Manual de usuario
(185 paginas)
(185 paginas)
Redes HP 100VG-ANYLAN B5426-90001 Manual de usuario
(39 paginas)
(39 paginas)
Redes HP DT-10 Manual de usuario
(20 paginas)
(20 paginas)
Redes HP AD583C Manual de usuario
(132 paginas)
(132 paginas)
Redes HP E5000 Guía de inicio rápido
(2 paginas)
(2 paginas)
Redes HP Cloud OS for Moonshot Guía de usuario
(126 paginas)
(126 paginas)
Redes HP hn220w Manual de inicio rápido
(12 paginas)
(12 paginas)
Redes HP ActivCard Smart Card Manual de usuario
(24 paginas)
(24 paginas)
Redes HP 3070A Manual de usuario
(24 paginas)
(24 paginas)
Redes HP 24SII Manual de usuario
(168 paginas)
(168 paginas)
Redes HP 510x Guía de usuario
(102 paginas)
(102 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales